When looking for a MAC address slot, start by using main BSSID slots 1-3,
afterwards use 16 repeater mode BSSID slots, then start using the slots
usually used for AP mode.
This search order should prevent unnecessary conflicts with AP mode interfaces
on the same PHY
Signed-off-by: Felix Fietkau <[email protected]>
Convert cpu_to_le16(le16_to_cpu(E1) + E2) to use le16_add_cpu().
Signed-off-by: Liu Shixin <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Release mcu message memory in case of failure in mt7915_mcu_add_beacon
routine
Fixes: e57b7901469fc ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Avoid firmware falling into spectrum mode since that will set
unexpected PSE/PLE thresholds which lead to Tx hang.
This mode should be cleaned before firmware download stage.
Signed-off-by: Chih-Min Chen <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Since the switch to using AQL by default, mtxq->retry_q is never filled anymore
Remove it to get rid of a few more unnecessary cycles in the tx path
Signed-off-by: Felix Fietkau <[email protected]>
Compared to mac80211 ACs, MT7915 queue numbers are in reverse order
There is no need for the defensive WARN_ON_ONCE, so we can simplify
the function to avoid the array lookup
Signed-off-by: Felix Fietkau <[email protected]>
Now that AQL works well on all mt76 drivers, completely replace the arbitrary
burst sizing and number of bursts logic for tx scheduling.
For the short period of time in which AQL does not work well yet, limit each
stations to 16 in-flight packets that have no estimated tx time.
This should avoid filling the queue if a station connects and queues up a
large number of packets before rate control information is available, especially
with hardware rate control
Signed-off-by: Felix Fietkau <[email protected]>
On 7615 and newer, DMA completion only triggers unmap, but not free of queued
skbs, since pointers to packets are queued internally.
Because of that, there is no need to process the main data queue immediately
on DMA completion.
To improve performance, mask out the DMA data queue completion interrupt and
process the queue only when we receive a txfree event.
This brings the number of interrupts under load down to a small fraction.
Signed-off-by: Felix Fietkau <[email protected]>
The previous scheduling round may have been limited by AQL.
More frames might be available after the tx free run.
Signed-off-by: Felix Fietkau <[email protected]>
Since DMA completion does not imply tx completion, it makes more sense to
poll for airtime from mt7915_mac_tx_free.
Reduce the runtime of the function by moving all items from dev->sta_poll_list
to a local list once and process any stations that were added afterwards
on the next run
Signed-off-by: Felix Fietkau <[email protected]>
- change the WTBL LMAC access function to set the mapping window only once
- use ac * 2 as offset, since each AC has separate words for rx and tx
Signed-off-by: Felix Fietkau <[email protected]>
Using dev_kfree_skb for tx skbs breaks AQL. This worked until now only
by accident, because a mac80211 issue breaks AQL on drivers with firmware
rate control that report the rate via ieee80211_tx_status_ext as struct
rate_info.
Signed-off-by: Felix Fietkau <[email protected]>
Use the txwi data as primary source information to avoid touching skb data
Use bitfield instead of state variable + spinlock
Signed-off-by: Felix Fietkau <[email protected]>
Queueing a per-sta work item from the tx free path can become very expensive
under load. This work is only supposed to pull rate control stats every
second and deal with rate control changes.
Additionally, the rate control update code was wrong, because it was
confusing bit masks and bit numbers in test_bit.
Fix this by introducing a dedicated device work item for rate control
updates, and by polling station stats from the phy mac work.
Stations requiring polling or rate control updates are added to lists
protected by dev->sta_poll_lock.
Signed-off-by: Felix Fietkau <[email protected]>
Only clear unmasked interrupts. If an interrupt is temporarily masked,
its pending events need to be processed later, even if another interrupt
happened in the mean time.
Signed-off-by: Felix Fietkau <[email protected]>
A small part of the first skb buffer is passed to the firmware for parsing
via DMA, while the full buffer is passed as part of the TXP.
Avoid calling DMA unmap on the first part (with a different length than map)
Signed-off-by: Felix Fietkau <[email protected]>
Smatch complains that "wcidx" value comes from the network and thus
cannot be trusted. In this case, it actually seems to come from the
firmware. If your wireless firmware is malicious then probably no
amount of carefulness can protect you.
On the other hand, these days we still try to check the firmware as much
as possible. Verifying that the index is within bounds will silence a
static checker warning. And it's harmless and a good exercise in kernel
hardening. So I suggest that we do add a bounds check.
Fixes: e57b7901469f ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets")
Signed-off-by: Dan Carpenter <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Avoid memcpy in Rx hot path to slightly improve performance.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
All drivers use this in pretty much the same way. Moving it to core helps with
some checks for the upcoming testmode support
Signed-off-by: Felix Fietkau <[email protected]>
Overwrite hw queue id for non-bufferable management frames if the hw/fw
support always txq (altxq) in order to be in sync with mac txwi code
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Felix Fietkau