mt7925_mcu_config_sniffer() hardcodes drop_err = 1, ignoring what
mac80211 actually requested via configure_filter(). FIF_FCSFAIL is
computed there but discarded instead of persisted.
Persist the FCSFAIL bit on the phy in mt7925_configure_filter() and
read it back in mt7925_mcu_config_sniffer() to derive drop_err, so the
firmware sniffer only passes through unfiltered/marginal frames when a
monitor listener actually requested them.
mt7925_mcu_config_sniffer() is only reached from mt7925_change_chanctx(),
which is itself only exercised on a monitor-mode chanctx, so this stays
scoped to monitor mode.
Fixes: c948b5da6bbe ("wifi: mt76: mt7925: add Mediatek Wi-Fi7 driver for mt7925 chips")
Tested-by: Devin Wittmayer <[email protected]>
Signed-off-by: Mark Anthony Agarro <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
The event TLV loops accept a zero-length TLV, which advances neither the
cursor nor the remaining length, so a malformed event hangs the caller.
mt7925_mcu_uni_roc_event() additionally walked past the end of the skb,
since it never checked the declared length against the remainder.
Replace the five open-coded loops with a shared iterator that rejects
lengths below the TLV header and beyond the remaining buffer, and check
the per-tag payload sizes before dereferencing them.
While here, make the RSSI monitor event read from the current TLV rather
than from the start of the list.
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
NAN operates with OFDM and does not support CCK, so the phy, rate
control and BSS rate TLVs must not fall back to 2.4 GHz. Borrow the
5 GHz band lookup to keep the STA records OFDM-only.
Fixes: 9824fb4edbf3 ("wifi: mt76: mt7925: add NAN MCU handling")
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Stella Liu <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
In the final version of 802.11be-2024, Transition Delay and Padding
Delay subfield are for both EMLSR and EMLMR. Depending if the mode is
EMLSR or EMLMR, the interpretation of the encoded value might change.
Define all the constants and helpers to interpret delay subfields both
in EMLSR and EMLMR mode.
Signed-off-by: Pablo Martin-Gomez <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Johannes Berg <[email protected]>
Introduce regulatory wiphy self-managed mode support for MT7925,
allowing the driver to manage its own regulatory domain independently
from the kernel's regulatory framework.
Signed-off-by: Charlie-cy Wu <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
The mt7925_tx_power_limit_tlv struct begins with a 4-byte rsv[] field
that acts as a UNI command header prefix. The firmware dispatcher did
not use the 4-byte rsv[] and will only check the payloads after the
4-byte rsv[] As a result, the total message length minus the 4-byte
prefix. Fix this by setting len to msg_len - 4.
Fixes: ccb1863 ("wifi: mt76: mt7925: add Mediatek Wi-Fi7 driver for mt7925 chips")
Signed-off-by: Jared.Huang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Newer mt7925 firmware uses a shorter WoW pattern TLV with rsv[3]. Select
the v2 layout based on the firmware build date, while keeping the old
layout for older firmware.
This also makes the WoW pattern handling compatible with newer devices
such as MT7928.
Tested-by: Stella Liu <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Use the active channel context to select the SNIFFER command band index on
MT7927, and fall back to the PHY chandef when no channel context is
available.
Also pass the same band index to the sniffer channel configuration. This
keeps monitor setup on the correct band, especially when multiple PHY band
contexts are present.
Fixes: 35a5dcc71735 ("wifi: mt76: mt7925: add MT7927 PCIe support")
Signed-off-by: Sean Wang <[email protected]>
Tested-by: Devin Wittmayer <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
With MLO, traffic for one TID can be sent on any active link. Programming
BA state only on the default link leaves the other active links out of
sync.
Program BA state on all active links instead.
Fixes: 766ea2cf5a39 ("Revert "wifi: mt76: mt7925: Update mt7925_mcu_uni_[tx,rx]_ba for MLO"")
Tested-by: Yao Ting Hsieh <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
mt7925_mcu_sta_ba() currently hides the BA target behind an implicit WCID
lookup.
Pass the WCID explicitly so the caller controls which BA context is being
programmed.
No functional change intended.
Tested-by: Yao Ting Hsieh <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
MT7927 needs DBDC enabled and uses a fixed firmware band assignment for
2.4GHz and 5/6GHz BSS contexts.
Reprogram the STA dev context when the channel context is assigned so the
firmware sees the updated band_idx before the BSS is used. This avoids
stale band programming after band changes.
Co-developed-by: Javier Tia <[email protected]>
Signed-off-by: Javier Tia <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Firmware may return wlan_failure when deactivating a BSS that is already
inactive. This is a valid teardown case and should not fail the remove
path.
Keep activation failures unchanged since they still indicate that firmware
failed to create or activate the BSS state.
Signed-off-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
The sta_rec_eht structure has a mcs_map_bw320 field, and the channel
width mapping includes NL80211_CHAN_WIDTH_320, but the 320MHz MCS/NSS
map was never copied from the station's EHT capabilities to the MCU TLV.
This prevents negotiation of 320MHz channel width even when both the
hardware and firmware advertise support for it.
Add the missing memcpy for the 320MHz MCS map, matching the existing
pattern for BW20, BW80, and BW160.
Tested-by: Marcin FM <[email protected]>
Tested-by: Cristian-Florin Radoi <[email protected]>
Tested-by: George Salukvadze <[email protected]>
Tested-by: Evgeny Kapusta <[email protected]>
Tested-by: Samu Toljamo <[email protected]>
Tested-by: Ariel Rosenfeld <[email protected]>
Tested-by: Chapuis Dario <[email protected]>
Tested-by: Thibaut François <[email protected]>
Tested-by: 张旭涵 <[email protected]>
Reviewed-by: Sean Wang <[email protected]>
Signed-off-by: Javier Tia <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
bss_rlm_tlv() in mt7925_mcu_bss_rlm_tlv() has no case for
NL80211_CHAN_WIDTH_320. When associated to a 320MHz BSS, the switch
falls through to default and sends bw=0 (CMD_CBW_20MHZ) to firmware
via BSS_RLM TLV. Firmware then configures the RX radio for 20MHz
and cannot decode the AP's 320MHz frames, resulting in complete data
path failure at 320MHz.
Add the missing NL80211_CHAN_WIDTH_320 case with CMD_CBW_320MHZ and
center_chan2.
Tested on ASUS RT-BE92U: 320MHz throughput goes from 0 Mbps to
841 Mbps (iperf3 -t30 -P8), PHY 4803 Mbps EHT-MCS11.
Reported-by: 张旭涵 <[email protected]>
Closes: https://github.com/openwrt/mt76/issues/927
Tested-by: 张旭涵 <[email protected]>
Tested-by: Marcin FM <[email protected]>
Tested-by: Cristian-Florin Radoi <[email protected]>
Tested-by: George Salukvadze <[email protected]>
Tested-by: Evgeny Kapusta <[email protected]>
Tested-by: Samu Toljamo <[email protected]>
Tested-by: Ariel Rosenfeld <[email protected]>
Tested-by: Chapuis Dario <[email protected]>
Tested-by: Thibaut François <[email protected]>
Reviewed-by: Sean Wang <[email protected]>
Signed-off-by: Javier Tia <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
With HW TX encap offload enabled, the mt76 firmware builds the 802.11
header for the 802.3 frame using the per-WCID context. For a STATION
vif the HDR_TRANS TLV currently sets ToDS=1, which makes the firmware
default to the BSSID as A1 and emit STA->AP-formatted frames
regardless of which peer the WCID points to.
For TDLS-paired peers this is wrong. Data frames go on air addressed
to the AP, the AP MAC-ACKs and silently drops them per IEEE 802.11z
(an AP must not forward to a TDLS-paired peer). Management and
control frames bypass the HW encap path and still reach the peer;
only user data fails.
Add MT_WCID_FLAG_TDLS_PEER, set it in mt7915, mt7921, mt7925 and
mt7996 sta-add paths when sta->tdls is true, and override the
HDR_TRANS TLV in mt76_connac_mcu_wtbl_hdr_trans_tlv() (Connac2 -
mt7915 / mt7921 / mt7922), mt7925_mcu_sta_hdr_trans_tlv() (mt7925)
and mt7996_mcu_sta_hdr_trans_tlv() (mt7996) to set ToDS=0, FromDS=0
when the flag is set. The 3-addr non-DS form matches what 802.11z
uses for direct links; the firmware then constructs the frame with
A1=peer rather than A1=BSSID. HW encap offload remains enabled for
AP and any non-TDLS traffic.
Verified on mt7925e + Samsung S938B over a 5 GHz HE 80 MHz channel
with iperf3 -t 30 to the TDLS peer:
before fix: over the TDLS direct link, 7 TDLS Setup action
frames and 3 RTS frames reach the peer; 0 QoS
Data frames make it through (mgmt/control paths
bypass HW encap, the data path does not). iperf3
stalls.
after fix: 2.90 GBytes transferred at 830 Mbit/s sustained,
0 TCP retransmits.
mt7915, mt7921, mt7922 and mt7996 are not regression-tested in this
change for lack of hardware. Their HDR_TRANS handling mirrors the
verified mt7925 change; the firmware behavior is shared across these
chips.
Signed-off-by: ElXreno <[email protected]>
Assisted-by: Claude:claude-opus-4-7 bpftrace tcpdump
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Drop the mt792x_vif_to_link() lookup in mt7925_mcu_wtbl_update_hdr_trans()
and pass the resolved mconf and mlink from the caller instead. The link
context is already known at the call site, making the lookup redundant.
This keeps the helper lookup-free and makes link ownership explicit.
No functional change intended.
Signed-off-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Drop the mt792x_sta_to_link() lookup in mt7925_mcu_wtbl_update_hdr_trans()
and pass the resolved mlink from the caller instead. The link context is
already known at the call site, making the lookup redundant.
This keeps the helper lookup-free and makes link ownership explicit.
No functional change intended.
Signed-off-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Replace the dead wcid NULL check in mt7925_mcu_sta_hdr_trans_tlv() with
a WARN_ON_ONCE() guard on mlink before dereferencing mlink->wcid.
wcid is always derived from mlink, so mlink is the only meaningful
object to validate here.
Signed-off-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Drop the mt792x_sta_to_link() lookup in mt7925_mcu_sta_hdr_trans_tlv()
and pass the resolved mlink from the caller instead. The link is
already known at the call site, making the lookup redundant.
This keeps the helper lookup-free and makes WCID selection explicit.
No functional change intended.
Signed-off-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Drop the mt792x_sta_to_link() lookup in mt7925_mcu_sta_update() and
pass the resolved mlink from the caller instead. The link context is
already known at the call site, making the lookup redundant.
This keeps the helper lookup-free and makes WCID selection explicit.
No functional change intended.
Signed-off-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Drop the mt792x_sta_to_link() lookup in mt7925_mcu_sta_mld_tlv() and
pass mlink and mconf from the caller instead. The link context is
already known at the call site, making the lookup redundant.
This keeps the helper lookup-free and makes MLD link selection
explicit.
No functional change intended.
Signed-off-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Drop the mt792x_sta_to_link() lookup in mt7925_mcu_bss_basic_tlv() and
pass the resolved WCID indices from the caller instead. The link
context is already known, so the lookup is redundant.
This makes link ownership explicit and keeps the helper lookup-free.
No functional change intended.
Signed-off-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Drop the mt792x_sta_to_link() lookup in mt7925_mcu_sta_amsdu_tlv() and
pass mlink from the caller instead. The link context is already known
so the lookup is redundant.
This makes link ownership explicit and keeps the helper lookup-free.
No functional change intended.
Signed-off-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
The previous implementation of __mt7925_mcu_set_clc() set the TLV length
field (.len) incorrectly during CLC command construction. The length was
initialized as sizeof(req) - 4, regardless of the actual segment length.
This could cause the WiFi firmware to misinterpret the command payload,
resulting in command execution errors.
This patch moves the TLV length assignment to after the segment is
selected, and sets .len to sizeof(req) + seg->len - 4, matching the
actual command content. This ensures the firmware receives the
correct TLV length and parses the command properly.
Fixes: c948b5da6bbe ("wifi: mt76: mt7925: add Mediatek Wi-Fi7 driver for mt7925 chips")
Cc: [email protected]
Signed-off-by: Quan Zhou <[email protected]>
Acked-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/f56ae0e705774dfa8aab3b99e5bbdc92cd93523e.1772011204.git.quan.zhou@mediatek.com
Signed-off-by: Felix Fietkau <[email protected]>
mt76_connac_mcu_alloc_sta_req() allocates an skb which is expected to
be freed eventually by mt76_mcu_skb_send_msg(). However, currently if
an intermediate function fails before sending, the allocated skb is
leaked.
Specifically, mt76_connac_mcu_sta_wed_update() and
mt76_connac_mcu_sta_key_tlv() may fail, leading to an immediate memory
leak in the error path.
Fix this by explicitly freeing the skb in these error paths.
Commit 7c0f63fe37a5 ("wifi: mt76: mt7996: fix memory leak on
mt7996_mcu_sta_key_tlv error") made a similar change.
Compile tested only. Issue found using a prototype static analysis tool
and code review.
Fixes: d1369e515efe ("wifi: mt76: connac: introduce mt76_connac_mcu_sta_wed_update utility routine")
Fixes: 6683d988089c ("mt76: connac: move mt76_connac_mcu_add_key in connac module")
Fixes: 4f831d18d12d ("wifi: mt76: mt7915: enable WED RX support")
Fixes: c948b5da6bbe ("wifi: mt76: mt7925: add Mediatek Wi-Fi7 driver for mt7925 chips")
Signed-off-by: Zilin Guan <[email protected]>
Link: https://patch.msgid.link/[email protected]
Set the MT76_STATE_MCU_RUNNING bit only after mt7921_load_clc()
has successfully completed. Previously, the MCU_RUNNING state
was set before loading CLC, which could cause conflict between
chip mcu_init retry and mac_reset flow, result in chip init fail
and chip abnormal status. By moving the state set after CLC load,
firmware initialization becomes robust and resolves init fail issue.
Signed-off-by: Quan Zhou <[email protected]>
Reviewed-by: [email protected]
Link: https://patch.msgid.link/19ec8e4465142e774f17801025accd0ae2214092.1763465933.git.quan.zhou@mediatek.com
Signed-off-by: Felix Fietkau <[email protected]>
The selection of MLO mode should depend on the capabilities of the STA
rather than those of the peer AP to avoid compatibility issues with
certain APs, such as Xiaomi BE5000 WiFi7 router.
Fixes: 69acd6d910b0c ("wifi: mt76: mt7925: add mt7925_change_vif_links")
Signed-off-by: Leon Yen <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
The implementation amounts to setting the driver flag
IEEE80211_VIF_SUPPORTS_CQM_RSSI, and then providing
mechanisms for continuously updating enough information
to be able to provide notifications to userspace when
RSSI drops below a certain threshold
Signed-off-by: Jack Kao <[email protected]>
Signed-off-by: Ming Yen Hsieh <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
MediaTek has asked to switch from the ISC license to BSD-3-Clause-Clear,
in order to improve clarity and the legal integrity of the code.
The BSD-3-Clause license includes the "no endorsement" clause, which is
important for protecting the reputation of the original authors and
contributors by preventing unauthorized use of their names for endorsement
purposes.
This clause is absent in the BSD-2-Clause license, which is more permissive
but lacks this specific protection.
This change also cleans up the license of some Kconfig/Makefile files,
which were accidentally marked as GPL.
The GPL 2.0 remains in use on mt76x0, as well as two source files in mt7615
for which the license situation still needs to be clarified.
Signed-off-by: Felix Fietkau <[email protected]>
Set `tx_power_tlv->len` to `msg_len` instead of `sizeof(*tx_power_tlv)`
to ensure the correct message length is sent to firmware.
Cc: [email protected]
Fixes: c948b5da6bbe ("wifi: mt76: mt7925: add Mediatek Wi-Fi7 driver for mt7925 chips")
Signed-off-by: Ming Yen Hsieh <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
The ssid->ssids[] and sreq->ssids[] arrays have MT7925_RNR_SCAN_MAX_BSSIDS
elements so this >= needs to be > to prevent an out of bounds access.
Fixes: 8284815ca161 ("wifi: mt76: mt7925: add RNR scan support for 6GHz")
Signed-off-by: Dan Carpenter <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Update the destination index to use 'n_ssids', which is incremented only
when a valid SSID is present. Previously, both mt76_connac_mcu_hw_scan()
and mt7925_mcu_hw_scan() used the loop index 'i' for the destination
array, potentially leaving gaps if any source SSIDs had zero length.
Cc: [email protected]
Fixes: c948b5da6bbe ("wifi: mt76: mt7925: add Mediatek Wi-Fi7 driver for mt7925 chips")
Signed-off-by: Michael Lo <[email protected]>
Signed-off-by: Ming Yen Hsieh <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
