In order to reduce number of received interrupts and power consumption,
enable hw beacon filter if runtime-pm is enabled
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce runtime-pm knob in mt7615 debugfs in order to enable/disable
runtime pm available in offload firmware
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Check MT76_STATE_PM in mt7615_driver_own/mt7615_firmware_own
in order to not requested power ownership if it is already granted
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Double-check if the device is in low-power state before accessing
registermap in mt7615_sta_rate_tbl_update() and in
mt7615_led_set_config()
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Run mt7615_pm_wake()/mt7615_pm_power_save_sched() directly in order to
wake the device from low power state in mt7615_mac_sta_{add,remove}
since they run holding mt76 mutex in common mt76 code
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Queue frames pushed by mac80211 running mt7615_tx if the device is
low-power state. Run wake workqueue in order to swicth to full-power
before transmitting pending frames
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Make sure the device is in full-power before pulling frames from
mac80211 queues
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Make sure to run mt7615_mcu_set_roc() holding mt76 mutex in order to
wake the device from low power state and avoid races
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Make sure to run mt7615_mcu_set_wmm() holding mt76 mutex in order to
wake the device from low power state and avoid races
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Make sure to run mt7615_dfs_init_radar_detector in mt7615_regd_notifier
holding mt76 mutex in order to avoid races and set the device in full
power
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Set device in full power before performing hw scan or hw scheduled scan
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Make sure to wake the device in mt7615_pci_suspend in order to properly
configure device registers before suspend
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt7615_update_survey utility routine in order to compute
survey stats without waking up the device since it runs holding mt76 lock.
Run mt7615_pm_wake directly in mt7615_update_channel since it can run
with mt76.mutex held if called by mac80211
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce runtime-pm power_save delayed work used to enable
low-power after an inactivity period
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Make sure the device is in full-power before uploading keys to the hw
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Make sure the device is in full-power before reading regs in debugfs
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt7615_mutex_{acquire,release} utility routines in order to
switch in full-power/low-power before/after accessing device register-map
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt7615_pm_wake utility routine to wake the device from
runtime low-power state (lower-power state is currently supported by
offload firmware for pcie devices).
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76 workqueue from usb to common code in order to be reused adding
low-power support for mt7663 chipset
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
According to the vendor sdk, mt7663 does not need to poll register after
firmware own. Since just mt7622 polls status register, set proper
timeout value according to the vendor sdk
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Supports sending a configurable number of packets with a specific rate
and configurable tx power levels / antenna settings, as well as displaying
rx statistics.
Signed-off-by: Felix Fietkau <[email protected]>
All drivers use this in pretty much the same way. Moving it to core helps with
some checks for the upcoming testmode support
Signed-off-by: Felix Fietkau <[email protected]>
Now that the bus access functions can use mapping for accessing full
register addresses, use it for WF_PHY registers to keep them constant.
Needed for follow-up work on testmode support
Signed-off-by: Felix Fietkau <[email protected]>
Unlike on earlier chips, DMA completion on MT7615 does not imply actually
having sent out any packets.
Since AQL will prevent filling the hardware queues and will only allow more
packets to be passed to the driver after tx completion, it makes much more
sense to schedule the tx tasklet there.
This is also needed for scheduling tx in testmode support
Signed-off-by: Felix Fietkau <[email protected]>
Avoid adding MT7615_EEPROM_SIZE twice.
Rename MT7615_EEPROM_EXTRA_DATA to MT7615_EEPROM_FULL_SIZE, since it already
includes MT7615_EEPROM_SIZE
Fixes: ad380ad1ebbe ("mt76: mt7615: add support for applying DC offset calibration from EEPROM")
Signed-off-by: Felix Fietkau <[email protected]>
Introduce U-APSD support in mt76 driver for AP interface
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Limits are used to update the channel max_power settings and also passed
to the firmware on channel changes
Signed-off-by: Felix Fietkau <[email protected]>
Fix up typo in Kconfig with indicating MT7663U is an 802.11ac device
Fixes: eb99cc95c3b6 ("mt76: mt7615: introduce mt7663u support")
Signed-off-by: Sean Wang <[email protected]>
Overwrite hw queue id for non-bufferable management frames if the hw
support always txq (altxq) in order to be in sync with mac txwi code
Fixes: cdad4874057d ("mt76: mt7615: add dma and tx queue initialization for MT7622")
Fixes: f40ac0f3d3c0 ("mt76: mt7615: introduce mt7663e support")
Suggested-by: Felix Fietkau <[email protected]>
Tested-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
acs and wmm index are swapped in mt7615_queues_acq respect to the hw
design
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Coverage class callback can potentially run in parallel with other
routines (e.g. mt7615_set_channel) that configures timing registers.
Run coverage class callback holding mt76 mutex
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
MT7611N is basically the same as MT7615N, except it only supports 5GHz
It is used by some TP-Link and Mercury wireless routers
Signed-off-by: DENG Qingfang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix hw_scan with ssid_type for specified SSID only
The definition for ssid_type in current firmware is that
ssid_type BIT(2) set actually for specified SSID + wildcard SSID.
ssid_type BIT(2) and ssid_type_ext BIT(0) both set actually for
specified SSID only;
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt7615_mcu_sched_scan_enable should be taken along with
mt7615_mcu_sched_scan_req to have proper scan plans initialization.
Fixes: bd39bd2f00c3 ("mt76: mt7663: introduce WoW with net detect support")
Co-developed-by: Wan-Feng Jiang <[email protected]>
Signed-off-by: Wan-Feng Jiang <[email protected]>
Co-developed-by: Soul Huang <[email protected]>
Signed-off-by: Soul Huang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
switch to per-vif ps support since mt7615 offload firmware can handle it
properly. This patch allows enabling/disabling power-save support on p2p
interface
Tested-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce remain_on_channel support to mt7615 driver if the device is
running offload firmware
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce essential bss information for multiple vifs hw_scan in
mt7615_mcu_uni_add_dev adding the interface
Signed-off-by: Sean Wang <[email protected]>
Co-developed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Differentiate hw scan channel time between passive and active scan
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
