Add missing register definitions in order to enable sensitivity tuning
for mt7663 driver
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce support for mt7663u 802.11ac 2x2:2 chipset to mt7615 driver.
Main difference respect to pcie code base is the usb code needs to
configure wtbl from non-atomic context
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Create mt7615-common module in order to collect shared code between usb
and mmio code. Move the following source files in mt7615-common module:
- main.c
- init.c
- mcu.c
- mac.c
- debugfs.c
- eeprom.c
- trace.c
Create the following source files for mmio only source code and move them
in mt7615e module:
- pci_init.c
- dma.c
- pci_mac.c
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
make mac_work per phy instead of per device and fix a possible deadlock
in mt7615_stop since mt7615_mac_work runs holding mt76 mutex
Fixes: fdd2e570764c2 ("mt76: mt7615: add dual-phy support for mac80211 ops")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix DMA unmap length estimation in mt7615_txp_skb_unmap_hw for mt7622
chipset
Fixes: 6aa4ed7927f1 ("mt76: mt7615: implement DMA support for MT7622")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Check that val is not zero before aggr_per estimation in order to avoid a
possible division by 0
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Generalize mt7615_rate_desc introducing mt7615_wtbl_desc and
mt7615_key_desc data structures in order to configure the hw wtbl
in a non-atomic context for usb devices
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove key dependency from mt7615_mac_wtbl_update_key and export
mt7615_mac_wtbl_update_key, mt7615_mac_wtbl_update_pk and
mt7615_mac_wtbl_update_cipher in order to reuse them in usb code.
Move mt7615_mac_get_cipher in mac.h
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt7615_mac_wtbl_addr in mac.h and add inline qualifier in order to
be reused adding usb support to mt7615 driver
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move register configuration out of mt7615_mac_set_rates since usb
driver can't access device register in interrupt context. Introduce
mt7615_mac_update_rate_desc routine to report rate info to
mt7615_mac_set_rates
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Disable dfs RDD mcu commands for mt7663 driver since they are not
currently supported by the 7663 firmware
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Make scs configurable per phy since most of the chipsets do not
support dbdc
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Simplify mib macros and use proper type for related counters.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In order to reuse mt7615 code adding support for mt7663e driver,
introduce mt7615e_reg_map since mt7663e and mt7615 rely on a
different base registers definitions.
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Co-developed-by: Ryder Lee <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt7615_mcu_set_beacon_offload, mt7615_mcu_set_dev and
mt7615_mcu_set_bss routine in mt7615_mcu_ops data structure.
This is a preliminary patch to support mt7663 firmware
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This if statement was supposed to be deleted, but it wasn't. It means
that we sometimes don't set the sensitivity correctly.
Fixes: 2cad515ece8a ("mt76: mt7615: add missing settings for simultaneous dual-band support")
Signed-off-by: Dan Carpenter <[email protected]>
When injecting beacon frames via monitor interface, they must not be sent to
the beacon hardware queue, because they don't follow normal hardware beacon tx
rules.
Fix sending them by adding a flag to mt7615_mac_write_txwi that selects the
beacon queue for tx, and use it only from mt7615_mcu_set_bcn.
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt76_mcu data structure to contain common fields between
mt76u_mcu and mt76e_mcu.
Initialize mcu common fields in mt76_alloc_device().
Rely on mt76_mcu in mt76_mcu_rx_event and in mt76_mcu_get_response
in order to reuse them in usb code
Signed-off-by: Lorenzo Bianconi <[email protected]>
Overwriting the RMAC_CHFREQ register is not reliable enough, as the firmware
could potentially write it again.
Since there is no PHY index indication in the rx info, we need to use another
way:
If both PHYs are using different channels, find the PHY where chfreq matches
the register value.
The only corner case remaining is when both PHYs are using the same channel.
In that case, the per-packet noise value on the primary PHY will have
information belonging to the chains of the secondary PHY from the previous
received packet of that PHY. The secondary PHY will set noise to 0 for extra
chains.
Signed-off-by: Felix Fietkau <[email protected]>
Fix the following sparse warning in mt7615_write_hw_txp:
warning: incorrect type in assignment (different base types)
expected restricted __le16
got unsigned long
Signed-off-by: Lorenzo Bianconi <[email protected]>
When the firmware detects a problem, it needs the host to stop/reset DMA and
resume it again when the hardware state has been reset.
Signed-off-by: Felix Fietkau <[email protected]>
MT7622 does not have the CR4 microcontroller sitting in the data path.
Because of that, it uses the chip's native tx descriptor format instead of
something parsed and converted by the firmware.
Co-developed-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce dfs radar pattern specs in mt7615 driver in order to make
dfs debugging easier. Radar pulse/pattern thresholds are taken from
vendor SDK.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce token tracing support in mt7615_mac_tx_free routine
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mac_txdone tracepoint in common code in order to
be reused by mt7603 and mt7615 drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
MT7615 supports dual-wiphy which means that it can run on 2.4G and 5GHz
channels simultaneously, and driver should configure each band.
Add missing register settings, and refine band related definitions to
avoid duplicate codes.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add the capability to configure acktimeout for mt7615 driver. Moreover
configure slottime according to the value provided by mac80211
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Some compilers (tested with 4.8.5 from CentOS 7) fail properly process
FIELD_GET inside an inline function, which ends up in a BUILD_BUG_ON.
Convert inline function to a macro.
Fixes commit bf92e7685100 ("mt76: mt7615: add support for per-chain
signal strength reporting")
Reported in https://lkml.org/lkml/2019/9/21/146
Reported-by: kbuild test robot <[email protected]>
Signed-off-by: Pablo Greco <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Beacons and management frames need to explicitly select the alternate tx
queues in order to be sent out on the right phy
Signed-off-by: Felix Fietkau <[email protected]>
Program the RMAC CHFREQ registers to properly indicate the band that the
frames are received on.
Add some sanity checks to the programmed values, because the firmware
programs these registers differently
Signed-off-by: Felix Fietkau <[email protected]>
There are two DFS detectors on the chip. When using 160 MHz channel bandwidth
(not supported in dual-wiphy mode), both are used. Otherwise, one detector is
used per wiphy.
Rework the code to start/stop them separately per phy and to indicate the
radar event on the right phy based on the detector index
Signed-off-by: Felix Fietkau <[email protected]>
