Create mt7615-common module in order to collect shared code between usb
and mmio code. Move the following source files in mt7615-common module:
- main.c
- init.c
- mcu.c
- mac.c
- debugfs.c
- eeprom.c
- trace.c
Create the following source files for mmio only source code and move them
in mt7615e module:
- pci_init.c
- dma.c
- pci_mac.c
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
make mac_work per phy instead of per device and fix a possible deadlock
in mt7615_stop since mt7615_mac_work runs holding mt76 mutex
Fixes: fdd2e570764c2 ("mt76: mt7615: add dual-phy support for mac80211 ops")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
With MSI interrupts, IRQs must not be enabled from within the IRQ handler,
because that can lead to lost events.
Defer IRQ processing to a tasklet, which is also responsible for enabling
IRQs (to avoid race conditions against the handler)
Co-developed-by: Soul Huang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Avoid having to attempt hw scan and fall back to software for every scan
on devices/firmware without hw scan support
Signed-off-by: Felix Fietkau <[email protected]>
Introduce address parameter to mt7615_eeprom_init routine in order to be
reused adding usb support to mt7615 driver
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove mt76_wr(dev, MT_CSR(0x010), 0x8208) that would cause
MT_PCIE_IRQ_ENABLE to be disabled; MT_PCIE_IRQ_ENABLE should always keep
on enabled when the driver is running.
0x44064 is a not existing address
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Keep Rx filters default value if the firmware supports offload and
low power features.
Signed-off-by: Sean Wang <[email protected]>
Co-developed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Make scs configurable per phy since most of the chipsets do not
support dbdc
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt7615_init_mac_chain routine to configure per band mac
register since new devices (e.g. mt7663e) do not support dbdc
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add mt7615_init_device routine in order to be reused adding support for
mt7663 in mt7615 driver
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Unify code converting between the different txpower values. Always add/remove
the combined txpower delta before dividing half-dB values.
Also fix the combined txpower delta values. The correct half-dB delta for
3 chains is 9, not 8.
Signed-off-by: Felix Fietkau <[email protected]>
The second PHY receives no packets unless there is an active vif present.
Set the WANT_MONITOR_VIF flag to deal with that
Signed-off-by: Felix Fietkau <[email protected]>
When the firmware detects a problem, it needs the host to stop/reset DMA and
resume it again when the hardware state has been reset.
Signed-off-by: Felix Fietkau <[email protected]>
MT7622 does not have the CR4 microcontroller sitting in the data path.
Because of that, it uses the chip's native tx descriptor format instead of
something parsed and converted by the firmware.
Co-developed-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
MT7622 does not have a CR4 microcontroller, so it only uses its own N9
firmware.
Co-developed-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move WIPHY_FLAG_HAS_CHANNEL_SWITCH in mt76-core module since now all
drivers support Channel Switch Announcement
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The hardware does not support using the same MAC address for interfaces,
even if they are on different bands.
In the future this will be made configurable via device tree
Signed-off-by: Felix Fietkau <[email protected]>
MT7615 supports dual-wiphy which means that it can run on 2.4G and 5GHz
channels simultaneously, and driver should configure each band.
Add missing register settings, and refine band related definitions to
avoid duplicate codes.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Initialize brightness_set and blink_set callbacks to
mt7615_led_set_brightness and mt7615_led_set_blink in order to enable
LED support in mt7615 driver
Tested-by: Deng Qingfang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add the capability to configure acktimeout for mt7615 driver. Moreover
configure slottime according to the value provided by mac80211
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Loading the mcu firmware and waiting for it to boot takes a long time,
which adds a significant amount to the system boot time.
Fix this by running the mcu init from a workqueue and waiting for it to
complete before starting the phy or issuing mcu commands via debugfs
Signed-off-by: Felix Fietkau <[email protected]>
This is only used for testing for now. In the future it will be possible to
enable the second PHY through an proper API via device tree
Signed-off-by: Felix Fietkau <[email protected]>
There are two DFS detectors on the chip. When using 160 MHz channel bandwidth
(not supported in dual-wiphy mode), both are used. Otherwise, one detector is
used per wiphy.
Rework the code to start/stop them separately per phy and to indicate the
radar event on the right phy based on the detector index
Signed-off-by: Felix Fietkau <[email protected]>
Add support for an extra wiphy in mt76_set_channel and mt76_get_survey
This is preparation for supporting multiple wiphys per device to support the
concurrent dual-band feature of MT7615D
Signed-off-by: Felix Fietkau <[email protected]>
Parse configured {tx,rx} mask from eeprom data instead of just setting it
to four tx-rx streams
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move interface modes declaration in common code since now mt76
chipsets support all modes (NL80211_IFTYPE_STATION, NL80211_IFTYPE_AP,
NL80211_IFTYPE_MESH_POINT and NL80211_IFTYPE_ADHOC)
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Enable IFTYPE_ADHOC support on 7615 devices. The feature has been tested
using a mt76x2 device as wireless peer.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move SUPPORTS_REORDERING_BUFFER hw property configuration from chip
specific code to mt76_register_device since it is supported by all mt76
drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Poll per-station hardware counters available in WTBL after tx/rx
status events in order to report tx/rx airtime to mac80211 layer
Co-developed-by: Felix Fietkau <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Report tx time/rx time and obss time from hw mib counters to fill survey
info requested by mac80211
Co-developed-by: Felix Fietkau <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Enable Smart Carrier Sense algorithm by default in order to improve
performances in a noisy environment
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce Smart Carrier Sense support in order to tune device
sensitivity according to RTS error rate and False CCA reported by the
radio
Tested-by: Ryder Lee <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
