The error handling code was added in order to allow tx enqueue to fail after
calling .tx_prepare_skb. Since this can no longer happen, the error handling
code is unused.
Signed-off-by: Felix Fietkau <[email protected]>
Enable receiving other-unicast packets
Disable RX header translation in order to proprerly receive data packets
Signed-off-by: Felix Fietkau <[email protected]>
If user changes the channel without completely disabling the interface the
txpower_sku values reported track the old channel the device was operating on.
If user bounces the interface the correct power tables are applied.
mt7915_sku_group_len array gets updated before the channel switch happens so it
uses data from the old channel.
Fixes: ecb187a74e18 ("mt76: mt7915: rework the flow of txpower setting")
Fixes: f1d962369d56 ("mt76: mt7915: implement HE per-rate tx power support")
Reported-By: Chad Monroe <[email protected]>
Tested-by: Chad Monroe <[email protected]>
Signed-off-by: Allen Ye <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Correct per-device TLV lengths to avoid invalid operation in firmware.
( 64.040375:28:STATS-E)statsGetSingleHWCounter: MIB counter index = 65472 not supported.
This happens on mt7916/mt7986.
Fixes: b0bfa00595be ("wifi: mt76: mt7915: improve accuracy of time_busy calculation")
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The IEEE80211_VHT_CAP_EXT_NSS_BW value already indicates support for half-NSS
160 MHz support, so it is wrong to also advertise full 160 MHz support.
Fixes: c2f73eacee3b ("wifi: mt76: mt7915: add back 160MHz channel width support for MT7915")
Signed-off-by: Felix Fietkau <[email protected]>
Capabilities in vif->bss_conf are only initialized in AP mode.
For other modes, they should be enabled by default, in order to avoid a
mismatch.
Fixes: 885f7af7e544 ("wifi: mt76: mt7915: remove mt7915_mcu_beacon_check_caps()")
Signed-off-by: Felix Fietkau <[email protected]>
Move the following routines in mt76-connac lib since they are shared
between mt7915 and mt7921:
- mt76_connac2_tx_check_aggr
- mt76_connac2_txwi_free
- mt76_connac2_tx_token_put
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
ampdu_state field is used by most of the drivers, so move it in
mt76_wcid structure.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
poll_list field is used by most of the drivers, so move it in mt76_wcid
structure.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
sta_poll_list and sta_poll_lock are used by most of the drivers, so move
them in mt76_dev structure.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Due to AP stop improperly, mt7915 driver would face random command timeout
by chip fw problem. Migrate AP start/stop process to .start_ap/.stop_ap and
congiure BSS network settings in both hooks.
The new flow is shown below.
* AP start
.start_ap()
configure BSS network resource
set BSS to connected state
.bss_info_changed()
enable fw beacon offload
* AP stop
.bss_info_changed()
disable fw beacon offload (skip this command)
.stop_ap()
set BSS to disconnected state (beacon offload disabled automatically)
destroy BSS network resource
Based on "mt76: mt7921: fix command timeout in AP stop period"
Signed-off-by: Rany Hany <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Stop WFDMA transaction to avoid potential unexpected issue while doing
system recovery.
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The stats are clear-on-read, which makes it very difficult for tools
to adequately deal with wrapped stats and with keeping good totals.
So, accumulate these values when they are read from the firmware/radio
and present totals to user-space.
Signed-off-by: Ben Greear <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add support for the MediaTek MT7981 SoC which is similar to the MT7986
but with a newer IP cores and only 2x ARM Cortex-A53 instead of 4x.
Unlike MT7986 the MT7981 can only connect a single wireless frontend,
usually MT7976 is used for DBDC.
Signed-off-by: Alexander Couzens <[email protected]>
Signed-off-by: Daniel Golle <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mib_stats structure is shared by mostly all chipsets. Move it to shared
code.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Avoid blocking other statistics sinfo->filled when txrate is
unavailable.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Concurrent binding/non-binding skbs could be handled anywhere which leads
to mixed byte counting, so switch to use PPDU TxS reporting regardless Tx
paths when WED is active.
Fixes: 43eaa3689507 ("wifi: mt76: add PPDU based TxS support for WED device")
Co-developed-by: Ryder Lee <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
PPDU TxS can only report MPDU count whereas mac80211 requires MSDU scale
(NL80211_STA_INFO_TX_PACKETS), so switch to get MSDU counts from WA
statistic.
Note that mt7915 WA firmware only counts tx_packet for WED path, so driver
needs to take care of host path additionally.
Fixes: 43eaa3689507 ("wifi: mt76: add PPDU based TxS support for WED device")
Co-developed-by: Ryder Lee <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Get missing tx retries/failed counts from txfree done events and report
them via mt7915_sta_statistics().
Co-developed-by: Peter Chiu <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The background radar uses MT_RX_SEL2 as its band indication, so fix it.
Fixes: 7a53eecd5c87 (wifi: mt76: mt7915: check the correctness of event data)
Signed-off-by: StanleyYP Wang <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add support for the MediaTek MT7981 SoC which is similar to the MT7986
but with a newer IP cores and only 2x ARM Cortex-A53 instead of 4x.
Unlike MT7986 the MT7981 can only connect a single wireless frontend,
usually MT7976 is used for DBDC.
Signed-off-by: Alexander Couzens <[email protected]>
Signed-off-by: Daniel Golle <[email protected]>
Just a cosmetic patch to drop redundant prefix for txpower ouput text.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move some mac shared definitions between mt7996, mt7921 and mt7915 in
mt76_connac2_mac.h.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
gen_ppe_thresh routine is shared between mt7615, mt7915, mt7921 and
mt7996 so move it in mt76_connac module.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
sta_ps callback is just an empty stub for most of the drivers,
so get rid of them.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
irq_tasklet struct is used by most of the drivers (e.g. mt7915, mt7921,
mt7615, mt7663 and mt7996) so move it in common code.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce p2p-go/p2p-client support to mt7921 driver
CONNECTION_P2P_GC/GO is not supported with the current firmware
so we added mt76_dev to mt76_connac_mcu_sta_basic_tlv signature to
use CONNECTION_INFRA_STA/AP instead for p2p-client and p2p-go
respectively to make it work.
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Those capabilities have been added into ieee80211_bss_conf.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This helps avoid cleartext leakage of already queued or powersave buffered
packets, when a reassoc triggers the key deletion.
Cc: [email protected]
Signed-off-by: Felix Fietkau <[email protected]>
A number of users reported that this support was working fine before
it got removed. Add it back, but leave out the unsupported 80+80 mode.
Fixes: ac922bd60ace ("wifi: mt76: mt7915: remove BW160 and BW80+80 support")
Signed-off-by: Felix Fietkau <[email protected]>
If kernel do not enable CONFIG_HWMON, it may cause thermal
initialization to be done with temperature value 0 and then can not
transmit. This commit fixes it by setting trigger/restore temperature
before checking CONFIG_HWMON.
Fixes: 7d12b38ab6f6 ("wifi: mt76: mt7915: call mt7915_mcu_set_thermal_throttling() only after init_work")
Signed-off-by: Howard Hsu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Enable two PCIe interfaces (dev->hif2) support for mt7916 when WED is enabled.
Signed-off-by: Sujuan Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
On MT7986 the WiFi driver currently does not get automatically loaded,
requiring manual modprobing because the device tree compatibles are not
exported into metadata.
Add the missing MODULE_DEVICE_TABLE macro to fix this.
Fixes: 99ad32a4ca3a2 ("mt76: mt7915: add support for MT7986")
Signed-off-by: Lorenz Brun <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Drop the lock before returning -EINVAL.
Fixes: ecaccdae7a7e ("wifi: mt76: mt7915: rework mt7915_thermal_temp_store()")
Signed-off-by: Dan Carpenter <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add support to get EHT rate stats from ethtool.
This is the preliminary patch to add EHT support for mt7996.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt7915_mmio_wed_reset_complete and
mt7915_mmio_wed_reset_complete callbacks and the related wait
queues in order to wait for wed reset completion during wlan reset.
Tested-by: Daniel Golle <[email protected]>
Co-developed-by: Sujuan Chen <[email protected]>
Signed-off-by: Sujuan Chen <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In order to reduce possible memory allocation failures due to memory
fragmentation caused by page_frag_cache allocator, switch to page_pool
allocator for dma and usb mt76 drivers.
Remove per rx-queue page_frag_cache
Co-developed-by: Felix Fietkau <[email protected]>
Tested-by: Deren Wu <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Free mt76_txwi_cache pointer in mt7915_mmio_wed_init_rx_buf routine in
case of failure.
Fixes: 4f831d18d12d ("wifi: mt76: mt7915: enable WED RX support")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The previous commit forgot to remove a leftover check.
Fixes: 43eaa3689507 ("wifi: mt76: add PPDU based TxS support for WED device")
Reported-By: Sujuan Chen <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Enable RED to limit the number of token used by each band. If single band
uses too many tokens, it would hurt the throughput of the other bands.The
software path can solve this problem by AQL so enable RED for HW path only.
Reviewed-by: Shayne Chen <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
