MAC80211 doesn't care any decryption error in 802.3 path, so received
frame will be dropped if HW tell us that the cipher configuration is not
matched as well as the header has been translated to 802.3. This case only
appears when IEEE80211_FCTL_PROTECTED is 0 and cipher suit is not none in
the corresponding HW entry.
The received frame is only reported to monitor interface if HW decryption
block tell us there is ICV error or CCMP/BIP/WPI MIC error. Note in this
case the reported frame is decrypted 802.11 frame and the payload may be
malformed due to mismatched key.
Signed-off-by: Xing Song <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix a possible NULL pointer deference issue in mt7921_mac_write_txwi
routine if vif is NULL.
Fixes: 33920b2bf0483 ("mt76: add support for setting mcast rate")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce the basic configuration for BW160 capability in 7922
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Only set RX_FLAG_RADIOTAP_HE and RX_FLAG_RADIOTAP_HE_MU from with their
own decoder functions to prevent header calculation error.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The HW can apply header translation to first fragmented frame, and
ramaining fragmented frame can only keep 802.11 format. Check and
reverse the first fragmented frame to 802.11 format to make sure
them can be defragmented by mac80211.
Signed-off-by: Xing Song <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
There is a missing mt7921e_driver_own in the MT7921E reset procedure
since the mt7921 mcu.c has been refactored for MT7921S, that will
result in MT7921E reset failure, so add it back now.
Fixes: dfc7743de1eb ("mt76: mt7921: refactor mcu.c to be bus independent")
Reported-by: YN Chen <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
offload_flags have to be dropped for mt7921 because mt76.omac_idx 0 would
always run as station mode that would cause Tx encapsulation setting
is not applied to mac80211.
Also, drop IEEE80211_OFFLOAD_ENCAP_4ADDR too because it is not really
being supported.
Fixes: e0f9fdda81bd ("mt76: mt7921: add ieee80211_ops")
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
ARRAY_SIZE() is of type size_t, so the format specfier should
be %zu instead of %lu.
Fixes this build warning:
../drivers/net/wireless/mediatek/mt76/mt7921/main.c: In function ‘mt7921_get_et_stats’:
../drivers/net/wireless/mediatek/mt76/mt7921/main.c:1024:26: warning: format ‘%lu’ expects argument of type ‘long unsigned int’, but argument 4 has type ‘unsigned int’ [-Wformat=]
dev_err(dev->mt76.dev, "ei: %d SSTATS_LEN: %lu",
Signed-off-by: Randy Dunlap <[email protected]>
Cc: Sean Wang <[email protected]>
Cc: [email protected]
Cc: Felix Fietkau <[email protected]>
Cc: Lorenzo Bianconi <[email protected]>
Cc: Ryder Lee <[email protected]>
Cc: Kalle Valo <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Similar to mt7915 driver, add per-vif tx counters in ethtool.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move tx_amsdu histogram stats in mib_stats structure since registers are
clear-on-read
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to add ethtool stats to mt7921 driver.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Similar to mt7915 driver, add tx/rx statistics reporting through ethtool.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to introduce ethtool stats support to mt7921
driver.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to introduce mt7921s support.
Refactor mt7921_mcu_send_message to be sharable between mt7921s and
mt7921e.
Tested-by: Deren Wu <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rely on mcu_get_nic_capability to obtain Tx quota information
for the SDIO device, get PHY capability, MAC address and then we can
totally drop mt7921/eeprom.c and any unnecessary code.
Noting that mt76_connac_mcu_get_nic_capability should be run before set
flag MT76_STATE_MCU_RUNNING being set to setup the proper parameters
like Tx quota control before the device is started to running.
Tested-by: Deren Wu <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use physical address to unify the register access and reorder the
entries in fixed_map table to accelerate the address lookup for
MT7921e. Cosmetics the patch with adding an extra space to make all
entries in the array style consistent.
Tested-by: Deren Wu <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The longer event such as the event for mcu_get_nic_capability would hold
the data in paged fragment skb for the SDIO device so we turn the skb to
be linearized skb before accessing it to reuse the same event parser
betweem mt7921s and mt7921e.
Tested-by: Deren Wu <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to introduce mt7921s support.
MT7921_COMMON module grouping bus independent objects the both mt7921e and
mt7921s can share with and have to rely on.
Tested-by: Deren Wu <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to introduce mt7921s support.
Make init.c reusable between mt7921s and mt7921e
Tested-by: Deren Wu <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to introduce mt7921s support.
Make mcu.c reusable between mt7921s and mt7921e
Tested-by: Deren Wu <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to introduce mt7921s support.
make dma.c be used dedicately for mt7921e.
by moving out mt7921_tx_cleanup from dma.c to mcu.c and then renaming
mt7921_tx_cleanup to refect the exact thing the function actually does.
Finally, dma.c totally become pcie specific one, only needed to
be compiled only when CONFIG_MT7921E is enabled.
Tested-by: Deren Wu <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to introduce mt7921s support.
Split out a new pci_mac.c from mac.c to make mac.c reusable between
mt7921s and mt7921e.
Tested-by: Deren Wu <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to create a mt76 debugfs subir for ext-phy.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce __mt76_mcu_send_firmware routine to specify mcu message max
length. This is a preliminary patch to support mt7921s driver.
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove mt76_wcid pointer from mt76_tx_status_check signature since it is
always set to NULL
Tested-by: [email protected]
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce per-wcid idr to manage packet id for txs. This allow fast idr
lookup and skb queueing at the same time.
Tested-by: [email protected]
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Unlock 6GHz band if supported by the device. Configure HE 6G
capabilities.
Tested-by: Deren Wu <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
We should pass the error code to the caller immediately
to avoid the possible infinite retry to release the semaphore.
Fixes: 1c099ab44727 ("mt76: mt7921: add MCU support")
Co-developed-by: YN Chen <[email protected]>
Signed-off-by: YN Chen <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Robustify hardware initialization in the current driver probing flow
to get rid of the device is possibly lost after the machine boot due
to possible firmware abnormal state by trying to recover the failure
with more chances.
Tested-by: Leon Yen <[email protected]>
Tested-by: YN Chen <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove unused tx rate reporting through mcu tx done event since
now tx status is fully supported
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Report tx rate from tx status packets instead of receiving periodic mcu
event. This improves flexibility, accuracy and AQL performance, and
simplifies code flow for better readability.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce infrastructure support for tx status reporting
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Similar to mt7915, introduce mt7921_txwi_free to report tx rate to
mac80211. This is a preliminary patch to add proper tx status report.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
napi_schedule() can call __raise_softirq_irqoff(), which can perform softirq
handling, so it must not be called in a pure process context with BH enabled.
Signed-off-by: Felix Fietkau <[email protected]>
We shouldn't put back the device into fw own state after wifi reset at
driver unbind stage to fix the following error because that is not the
consistent state the current driver bind stage expects.
localhost ~ # echo 0000:01:00.0 > /sys/bus/pci/drivers/mt7921e/unbind
localhost ~ # echo 0000:01:00.0 > /sys/bus/pci/drivers/mt7921e/bind
...
[ 481.172969] mt7921e 0000:01:00.0: ASIC revision: feed0000
[ 482.133547] mt7921e: probe of 0000:01:00.0 failed with error -110
-bash: echo: write error: No such device
Fixes: c1af184ba830 ("mt76: mt7921: fix dma hang in rmmod")
Co-developed-by: YN Chen <[email protected]>
Signed-off-by: YN Chen <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Tested-by: Chen-Yu Tsai <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt7921 mac work can be idle for a long time due to runtime-pm so
update mib counters dumping phy stats
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
