MAC80211 doesn't care any decryption error in 802.3 path, so received
frame will be dropped if HW tell us that the cipher configuration is not
matched as well as the header has been translated to 802.3. This case only
appears when IEEE80211_FCTL_PROTECTED is 0 and cipher suit is not none in
the corresponding HW entry.
The received frame is only reported to monitor interface if HW decryption
block tell us there is ICV error or CCMP/BIP/WPI MIC error. Note in this
case the reported frame is decrypted 802.11 frame and the payload may be
malformed due to mismatched key.
Signed-off-by: Xing Song <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove always false if condition in get_omac_idx for sta type
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The HW can apply header translation to first fragmented frame, and
ramaining fragmented frame can only keep 802.11 format. Check and
reverse the first fragmented frame to 802.11 format to make sure
them can be defragmented by mac80211.
Signed-off-by: Xing Song <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
ieee80211_register_hw() is called with rtnl_lock held, and this could be
caused lockdep from a work item that's on a workqueue that is flushed
with the rtnl held.
Move mt7615_register_ext_phy() outside the init_work().
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Band0 and band1 share the same hardware, so band0 will stop Tx/Rx when
band1 performs Rx calibration. cal_cache is introduced to solve such
corner cases by moving necessary datas from channel_switch to bootup.
Co-developed-by: Peter Chiu <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rely on mcu_get_nic_capability to obtain Tx quota information
for the SDIO device, get PHY capability, MAC address and then we can
totally drop mt7921/eeprom.c and any unnecessary code.
Noting that mt76_connac_mcu_get_nic_capability should be run before set
flag MT76_STATE_MCU_RUNNING being set to setup the proper parameters
like Tx quota control before the device is started to running.
Tested-by: Deren Wu <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add parse_irq to handle that interrupt status structure is
different between mt7663s and mt7921s.
This is a preliminary patch to introduce mt7921s driver
Tested-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move sdio common code in mt76_sdio module.
This is a preliminary patch to support mt7921s devices.
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Export mt76s_alloc_rx_queue and mt76s_alloc_tx utility routines in order
to allow mt7921s driver to configure a different main rx queue.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to create a mt76 debugfs subir for ext-phy.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fixes: d8d59f66d136 ("mt76: mt7615: support 16 interfaces").
commit 7f4b7920318b ("mt76: mt7615: add ibss support") introduced IBSS
and commit f4ec7fdf7f83 ("mt76: mt7615: enable support for mesh")
meshpoint support.
Both used in the "get_omac_idx"-function:
if (~mask & BIT(HW_BSSID_0))
return HW_BSSID_0;
With commit d8d59f66d136 ("mt76: mt7615: support 16 interfaces") the
ibss and meshpoint mode should "prefer hw bssid slot 1-3". However,
with that change the ibss or meshpoint mode will not send any beacon on
the mt7622 wifi anymore. Devices were still able to exchange data but
only if a bssid already existed. Two mt7622 devices will never be able
to communicate.
This commits reverts the preferation of slot 1-3 for ibss and
meshpoint. Only NL80211_IFTYPE_STATION will still prefer slot 1-3.
Tested on Banana Pi R64.
Signed-off-by: Nick Hainke <[email protected]>
Remove mt76_wcid pointer from mt76_tx_status_check signature since it is
always set to NULL
Tested-by: [email protected]
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce per-wcid idr to manage packet id for txs. This allow fast idr
lookup and skb queueing at the same time.
Tested-by: [email protected]
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Without this change, garbage is seen in the hwmon name and sensors output
for mt7615 is garbled.
Fixes: 109e505ad944 ("mt76: mt7615: add thermal sensor device support")
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
napi_schedule() can call __raise_softirq_irqoff(), which can perform softirq
handling, so it must not be called in a pure process context with BH enabled.
Signed-off-by: Felix Fietkau <[email protected]>
./drivers/net/wireless/mediatek/mt76/mt7615/usb_sdio.c:172:8-9:WARNING:
return of 0/1 in function 'mt7663_usb_sdio_tx_status_data' with return
type bool
Return statements in functions returning bool should use true/false
instead of 1/0.
Generated by: scripts/coccinelle/misc/boolreturn.cocci
Reported-by: Zeal Robot <[email protected]>
Signed-off-by: jing yangyang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt7615_mcu_set_p2p_oppps routine in mt76_connac_lib module in order
to be reused in mt7921 driver
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt76_register_debugfs_fops routine in order to
define per-driver regs file operations and make sure the
device is up before reading or writing its registers
Fixes: 1d8efc741df8 'mt76: mt7921: introduce Runtime PM support'
Fixes: de5ff3c9d1a2 'mt76: mt7615: introduce pm_power_save delayed work'
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When clearing all existing pending tx slots, mt76_tx_complete_skb needs to
be used to free the skbs, to ensure that they are cleared from the status
list as well.
Cc: [email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Fix the following sparse warning in mt7615_mac_write_txwi routine:
drivers/net/wireless/mediatek/mt76/mt7615/mac.c:758:17:
warning: incorrect type in assignment
expected restricted __le32 [usertype]
got unsigned long
Fixes: 04b8e65922f63 ("mt76: add mac80211 driver for MT7615 PCIe-based chipsets")
Fixes: d4bf77bd74930 ("mt76: mt7615: introduce mt7663u support to mt7615_write_txwi")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Set macwork timeout value according to runtime-pm in order to reduce
power consumption
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Allow the user to enable runtime-pm for mt7663s driver
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Similar to mt7663e, rely on mt76_connac_pm_ref/mt76_connac_pm_unref to
check PM state and increment/decrement wake counter
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
As already done for mt7921 and mt7663e, rely on pm reference counting in
drv/fw_own
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The iv from RXD is only for TKIP_RSC/CCMP_PN/GCMP_PN, and it needs a
check for CCMP header insertion. Move mt76_cipher_type to mt76.h to
reduce duplicated code.
Signed-off-by: Xing Song <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When .sta_state is implemented, mac80211 assumes that the station entry is
usable after the NOTEXIST->NONE transition.
So we should create the sta entry as early as possible in order that
mac80211 pass assoc/auth frames to mt76 with the newly created sta entry,
and add .sta_assoc to mt76 core to refresh the sta entry again when sta is
being associated.
Fixes: 8aa5a9b7361c ("mt76: mt7921: enable deep sleep at runtime")
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
header files should use '/* SPDX ... */
Change from c file comment syle to header style
Signed-off-by: Tom Rix <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Reduce rx buffer size to 2048 for mt7921/mt7915/mt7615 since we
now support rx amsdu offload
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Maximum interval (in seconds) for schedule scan plan supported by
the offload firmware can be U16_MAX.
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Schedule power_save work running mt76_connac_pm_unref in order to reduce
power consumption
Tested-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Patch radar parameters to match the SDK to avoid possible false alarms.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Get rid of unnecessary if condition in mt7615_add_interface routine
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
It's much more accurate than .get_tsf + .set_tsf and switch to use
mt76_rmw to operate tsf registers.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Similar to mt7915, switching to use standard hwmon sysfs.
For reading temperature, cat /sys/class/ieee80211/phy*/hwmon*/temp1_input
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
As already done for mt7615 and mt7915, enable rx header translation
offload for mt7663 in order to reduce cpu load in the rx path.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
As already done for mt7915 and mt7921, free registered irq line if
mt7615_mmio_probe routine fails
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix theoretical NULL pointer dereference in mt7615_tx_prepare_skb and
mt7663_usb_sdio_tx_prepare_skb routines. This issue has been identified
by code analysis.
Fixes: 6aa4ed7927f11 ("mt76: mt7615: implement DMA support for MT7622")
Fixes: 4bb586bc33b98 ("mt76: mt7663u: sync probe sampling with rate configuration")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
