Add support to set SA/DA/BSSID in testmode.
During mass production stage, some test scripts or test equipments need
to set fixed addresses to detect or parse if a test is passed.
Also, MAC setting is necessary for some tx/rx tests with rx filter,
to make sure rx site only receives expected packets.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76_ethtool_worker_info in common code in order to be reused in
mt7921 driver.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to add ethtool stats to mt7921 driver.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Extend mcu_get_nic_capability to obtain tx resource for SDIO device,
MAC address, and PHY capability.
Tested-by: Deren Wu <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add parse_irq to handle that interrupt status structure is
different between mt7663s and mt7921s.
This is a preliminary patch to introduce mt7921s driver
Tested-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move sdio common code in mt76_sdio module.
This is a preliminary patch to support mt7921s devices.
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Export mt76s_alloc_rx_queue and mt76s_alloc_tx utility routines in order
to allow mt7921s driver to configure a different main rx queue.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to create a mt76 debugfs subir for ext-phy.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When received frame is decryped by hardware, CCMP PN is checked by
mt76.
When management frame protection (IEEE 802.11w) is used, we must use
a separate counter for tracking received CCMP packet number for the
management frames. The previously used counter was shared with data
frames and that can cause problems in detecting replays incorrectly
for robust management frames.
Add a new counter just for robust management frames to avoid this
issue.
Signed-off-by: Xing Song <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Each firmware piece with mt7915 and mt7921 do not have the MCU header to
reroute the packet to the internal RAM. So we do not need to consider the
MCU header size in __mt76_mcu_send_firmware.
Move the MCU header overhead calculation to mt76_mcu_send_firmware (for
older chipsets)
Fixes: e57b7901469f ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets")
Fixes: 1c099ab44727 ("mt76: mt7921: add MCU support")
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce __mt76_mcu_send_firmware routine to specify mcu message max
length. This is a preliminary patch to support mt7921s driver.
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Substitute sk_buff_head status_list with spinlock_t status_lock since we
just need it for locking
Tested-by: [email protected]
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove mt76_wcid pointer from mt76_tx_status_check signature since it is
always set to NULL
Tested-by: [email protected]
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce per-wcid idr to manage packet id for txs. This allow fast idr
lookup and skb queueing at the same time.
Tested-by: [email protected]
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Configure 6GHz channels defining mcu channel domain. This is a
preliminary patch to enable 6GHz band on mt7921 devices.
Tested-by: Deren Wu <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add tx-mode (ofdma, ht, vht, HE) histogram,
tx-ru-idx histogram, and tx-bandwidth histogram.
Also add tx attempts and tx success counters.
All of this is per-station.
Signed-off-by: Ben Greear <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Drop MT_DRV_AMSDU_OFFLOAD after introducing IEEE80211_OFFLOAD_ENCAP_ENABLED
flag in mac80211. Driver now checks vif->offload_flags to know encap offload
status of each interface.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt76_register_debugfs_fops routine in order to
define per-driver regs file operations and make sure the
device is up before reading or writing its registers
Fixes: 1d8efc741df8 'mt76: mt7921: introduce Runtime PM support'
Fixes: de5ff3c9d1a2 'mt76: mt7615: introduce pm_power_save delayed work'
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Mesh and ad-hoc interfaces allow users to set mcast rate through
NL80211_ATTR_MCAST_RATE, so rework mt76_default_basic_rate() to
adapt that.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Report tx rate from tx status packets instead of receving periodic mcu
event. This improves flexibility, accuracy and AQL performance, and
simplifies code flow for better readability.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
add .set_sar_specs to allow configuring SAR power limitations on the
frequency ranges from the userland.
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: YN Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
add mt76_default_basic_rate to mt76 core more devices can rely on
to send frames which require the rate in the basic rates.
Suggested-by: Ryder Lee <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
PHY offset in either .hw_value or .hw_value_short for mt7615, mt7663,
mt7915 and mt7921 device all start at bit 6, not 8.
Suggested-by: Ryder Lee <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The iv from RXD is only for TKIP_RSC/CCMP_PN/GCMP_PN, and it needs a
check for CCMP header insertion. Move mt76_cipher_type to mt76.h to
reduce duplicated code.
Signed-off-by: Xing Song <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In order to remove duplicated code, move mt76_get_next_pkt_id routine
in mt76.h
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt76_connac_mcu_get_nic_capability utility routine to poll
device capabilities returned by mcu fw for CE devices (mt7663/mt7921).
This is a preliminary patch to introduce 6GHz support.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use ieee80211_tx_status_ext instead of ieee80211_free_skb and
ieee80211_tx_status. This makes it compatible with 802.3 encap offload
and improves performance by removing a redundant sta lookup
Signed-off-by: Felix Fietkau <[email protected]>
In order to remove duplicated code, move mt76_token_init in
mt76_alloc_device routine
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
since mcu_reset it used only by mt7921, move the reset callback to
mt7921_mcu_parse_response routine and get rid of the function pointer.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move token management in mt76 common module since it is shared between
mt7615, mt7915 and mt7921 drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move token_lock, token and token_count data structures in mt76_dev.
This is a preliminary patch to move token management in mt76 common
module since it is shared by mt7615, mt7915 and mt7921 drivers.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add the capability to define a custom rx napi callback for each driver.
This is a preliminary patch to properly support runtime-pm on rx side
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt7615_tx_worker routine as mt76 tx worker callback for
mt7663.
Rely on mt76_connac_pm_ref/mt76_connac_pm_unref to check PM state and
increment/decrement wake counter
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When the EEPROM data is read from flash, it can contain pre-calibration
data, which can save calibration time.
Note that group_cal can save 30% bootup calibration time, and dpd_cal can
save 75% channel switching time.
Tested-by: Bo Jiao <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add support to send larger packet in testmode to meet requirements
of some test cases.
The limit of max packet size is determined based on tx rate mode setting.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Frame reception timestamp (low 32-bits) that indicates the value of the
local TSF timer value at the time the first bit of the MAC header in the
received frame (PPDU unit) arriving at the MAC.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Export mt76_dma_rx_cleanup routine in mt76_queue_ops data structure.
This is a preliminary patch to introduce mt7921 chip reset support.
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt76_dma_queue_reset utility routine to reset a given hw
queue. This is a preliminary patch to introduce mt7921 chip reset
support.
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mcu_reset function pointer in mt76_mcu_ops structure in order
to run hw related reset function for the mcu running on the chipset.
This is a preliminary patch to introduce chip reset for mt7921 devices.
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
For AP and Client mode, the hardware can pass received packets as 802.3 frames
that can be passed to the network stack as-is.
Signed-off-by: Felix Fietkau <[email protected]>
Enable hw rx-amsdu de-aggregation support available in 7915 devices.
This is a preliminary patch to enable rx checksum offload
Signed-off-by: Lorenzo Bianconi <[email protected]>
