This allows tx scheduling and tx cleanup to run concurrently
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move pre_tbtt_tasklet tasklet in mt76_dev data structure since
it is used by all drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move beacon_int in mt76_dev data structure since it is used by
all drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Pass skb pointer to tx_prepare_skb through mt76_tx_info data structure.
This is a preliminary patch to properly support dma error path for
new chipsets (e.g. 7615)
Signed-off-by: Lorenzo Bianconi <[email protected]>
Move mac_work delayed work in mt76_dev data structure since
it is used by all drivers and it will be reused adding mac work to
mt7615
Signed-off-by: Lorenzo Bianconi <[email protected]>
If the MT_TXD3_SN_VALID flag is not set in the tx descriptor, the hardware
assigns the sequence number. However, the rest of the code assumes that the
sequence number specified in the 802.11 header gets transmitted.
This was causing issues with the aggregation setup, which worked for the
initial one (where the sequence numbers were still close), but not for
further teardown/re-establishing of sessions.
Additionally, the overwrite of the TID sequence number in WTBL2 was resetting
the hardware assigned sequence numbers, causing them to drift further apart.
Fix this by using the software assigned sequence numbers
Signed-off-by: Felix Fietkau <[email protected]>
Add mt76_tx_info as auxiliary data structure to pass values
to tx_prepare_skb pointer. This is a preliminary patch to add
support for new chipsets (e.g. mt7615)
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt76_sw_queue data structure in order to support new
chipsets (e.g. mt7615) that have a shared hardware queue for all traffic
identifiers. mt76_sw_queue will be used to track outstanding packets
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove mt76_queue dependency from tx_complete_skb function pointer and
rely on mt76_tx_qid instead. Remove flush from tx_complete_skb
signature. This is a preliminary patch to introduce mt76_sw_queue
support
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove mt76_queue dependency from tx_prepare_skb function pointer and
rely on mt76_tx_qid instead. This is a preliminary patch to introduce
mt76_sw_queue support
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use the correct variable in the check. Fixes an uninitialized variable warning
Reported-by: Gustavo A. R. Silva <[email protected]>
Fixes: c8846e1015022 ("mt76: add driver for MT7603E and MT7628/7688")
Signed-off-by: Felix Fietkau <[email protected]>
The vendor driver also does not enable it, and it has been shown to cause
some issues. It can be re-enabled for testing through debugfs
Signed-off-by: Felix Fietkau <[email protected]>
The tx ba window size which is set to HW should not
exceed the actual window size of the ba session,
otherwise the HW might aggregate more packets than
what's negotiated.
Signed-off-by: Felix Fietkau <[email protected]>
Sync CCK values with reference driver.
Use OFDM values obtained from the hardware reset value
Stop tx/rx on change only using the ARB_SCR register
Signed-off-by: Felix Fietkau <[email protected]>
The hardware needs to be notified of peers using dynamic SMPS mode
Fixes using dual-stream rates on some clients (e.g. Intel)
Signed-off-by: Felix Fietkau <[email protected]>
Clear pending PSE request bit in order to avoid having it trigger by the
firmware at a bad point in time.
Only clear AC queue stuck bits if the PSE reset succeeded
Signed-off-by: Felix Fietkau <[email protected]>
Reporting A-MPDU length from txs does not work, because only completed
subframes are reported. Trying to aggregate tx status report for one
completed A-MPDU does not work, because individual subframe retries can
be different.
Do not report A-MPDU length > 1 and pass individual subframe tx status
information to mac80211 to fix rate control errors
Signed-off-by: Felix Fietkau <[email protected]>
On MT76x2, the hardware does not report tx status in the FIFO register,
if the packet id is 0.
Change the allocation of packet IDs to use 0 for no-ack packets, 1 for
non-probing packets and 2-255 for packets with tx status requested.
Fixes rate control issues
Signed-off-by: Felix Fietkau <[email protected]>
Each rate retry slot takes up MT7603_RATE_RETRY tries, and cannot be altered
based on mac80211 provided rate retry counts.
Signed-off-by: Felix Fietkau <[email protected]>
The second chain value is 0 if the second chain is disabled, which
would make the reported signal strength 0 as well.
Signed-off-by: Felix Fietkau <[email protected]>
Ported from the reference driver.
Should fix compliance with ETSI rules on preventing transmission while
energy detect values are above the threshold.
Relax rules for non-ETSI regdomains
Signed-off-by: Felix Fietkau <[email protected]>
