This reports signal strength of ACK packets from the peer as measured
at each interface.
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fixed coverity issue with resource leaks at variable "fw" going out of
scope leaks the storage it points to mt7921_check_offload_capability().
Reported-by: coverity-bot <[email protected]>
Addresses-Coverity-ID: 1527806 ("Resource leaks")
Fixes: 034ae28b56f1 ("wifi: mt76: mt7921: introduce remain_on_channel support")
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The firmware can have the capability to manage the channel context
scheduling on multiple roles running on the device including Station,
AP and P2P GC/GO mode (will be extended based on the future patchset)
to help users sharing the network with others on a single device.
The firmware is able to support the channel chanctx up to 2 interface
simultaneously running on the different channels.
Another thing to be noted is that before the driver is going sent out the
management frames, the driver has to get the privilege from the firmware
to occupy the current channel context until the frame handshake is
completed and then get the privilege back to the firmware.
Co-developed-by: Deren Wu <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
We should update CLC config before SAR set to synchronize all
related settings.
Fixes: 23bdc5d8cadf ("wifi: mt76: mt7921: introduce Country Location Control support")
Signed-off-by: YN Chen <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce remain_on_channel support. Additionally, we add
mt7921_check_offload_capability to disable .remain_on_channel and
.cancel_remain_on_channel and related configuration because those
operations would rely on the fundamental MCU commands that will be only
supported with newer firmware.
Co-developed-by: Deren Wu <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Country Location Control (CLC) is an additional control for country rules
in firmware. We introduce this new feature to make sure mt7921 series
working properly in all region.
The addtional policies would be put into firmware based on differnt
regions. mt76 driver should be in charge of submitting per region policy.
Reviewed-by: Sean Wang <[email protected]>
Tested-by: YN Chen <[email protected]>
Co-developed-by: Deren Wu <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Ming Yen Hsieh <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The current driver has worked with HW beacon filter and connection
monitor all the way, here we move the enablement into the initialization
stage like other HW features being done to get rid of others are
confused why these configurations would be changed at runtime.
We still leave a way to turn off these offload features in debugfs knobs
but that is just for debugging purposes.
Tested-by: Deren Wu <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Enlarge maximum MPDU length to 11454 that both mt7921/mt7922 can support.
After this fixing, we can get better performance.
Fixes: 5c14a5f944b9 ("mt76: mt7921: introduce mt7921e support")
Tested-by: Ming Yen Hsieh <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt7921/mt7922 support HE max aggregation subframes 256 for both tx/rx.
Get better throughput then before.
Fixes: 94bb18b03d43 ("mt76: mt7921: fix max aggregation subframes setting")
Tested-by: Ming Yen Hsieh <[email protected]>
Reviewed-by: Sean Wang <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
According IEEE Std 802.11-2020, its definition is:
Indicates whether the STA is capable of interpreting the Extended NSS BW
Support subfield of the VHT Capabilities Information field.
Some APs, such as Xiaomi AX6000, would check this one for BW settings.
mt76 driver can get max BW capability only if the this field is confgured
properly.
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Ming Yen Hsieh <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add new function mt7921_set_tx_sar_pwr() to update SAR power from
.set_sar_specs and ACPI setting. Both settings would be merged into
mt76_freq_range_power for final tx power value.
Reviewed-by: Sean Wang <[email protected]>
Co-developed-by: Ming Yen Hsieh <[email protected]>
Signed-off-by: Ming Yen Hsieh <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In ACPI SAR enabled device, mt7921 should read power limit in ACPI config.
The limit value would be applied to regular tx power settings in mt76.
Two major functionalities added:
1. Get SAR power table through ACPI.
2. Read power in Dynamic/Geo SAR table for tx power limit.
Table note
MTDS: Dynamic SAR table
MTGS: Geo SAR table
MTCL: Country List table (for 6GHz support)
Reviewed-by: Sean Wang <[email protected]>
Co-developed-by: Quan Zhou <[email protected]>
Signed-off-by: Quan Zhou <[email protected]>
Co-developed-by: Ming Yen Hsieh <[email protected]>
Signed-off-by: Ming Yen Hsieh <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add ipv6 NS offload for WoWLAN state.
Tested in this way:
1. Put device-A into WoW state.
2. ping6 from device-B to device-A.
3. In sniffer, see Neighbour advertisement from device-A.
Reviewed-by: Sean Wang <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Ming Yen Hsieh <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Firmware initialization can take a while. Move mt7921_init_hw routine in
a dedicated work in order to not slow down bootstrap process.
Tested-by: Deren Wu <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Apply sleep mode by default to reduce power consumption as possible.
Signed-off-by: Sean Wang <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Toggle runtime-pm and deep-sleep configuration adding/removing
a montior vif in order to forward all tx/rx frames to mac80211.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Tested-by: Sven Eckelmann <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move wiphy SAR capability configuration in mt76 module and remove
duplicated code.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce the basic configuration for BW160 capability in 7922
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rely on mcu_get_nic_capability to obtain Tx quota information
for the SDIO device, get PHY capability, MAC address and then we can
totally drop mt7921/eeprom.c and any unnecessary code.
Noting that mt76_connac_mcu_get_nic_capability should be run before set
flag MT76_STATE_MCU_RUNNING being set to setup the proper parameters
like Tx quota control before the device is started to running.
Tested-by: Deren Wu <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to introduce mt7921s support.
MT7921_COMMON module grouping bus independent objects the both mt7921e and
mt7921s can share with and have to rely on.
Tested-by: Deren Wu <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to introduce mt7921s support.
Make init.c reusable between mt7921s and mt7921e
Tested-by: Deren Wu <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to introduce mt7921s support.
Make mcu.c reusable between mt7921s and mt7921e
Tested-by: Deren Wu <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Robustify hardware initialization in the current driver probing flow
to get rid of the device is possibly lost after the machine boot due
to possible firmware abnormal state by trying to recover the failure
with more chances.
Tested-by: Leon Yen <[email protected]>
Tested-by: YN Chen <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove unused tx rate reporting through mcu tx done event since
now tx status is fully supported
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
We shouldn't put back the device into fw own state after wifi reset at
driver unbind stage to fix the following error because that is not the
consistent state the current driver bind stage expects.
localhost ~ # echo 0000:01:00.0 > /sys/bus/pci/drivers/mt7921e/unbind
localhost ~ # echo 0000:01:00.0 > /sys/bus/pci/drivers/mt7921e/bind
...
[ 481.172969] mt7921e 0000:01:00.0: ASIC revision: feed0000
[ 482.133547] mt7921e: probe of 0000:01:00.0 failed with error -110
-bash: echo: write error: No such device
Fixes: c1af184ba830 ("mt76: mt7921: fix dma hang in rmmod")
Co-developed-by: YN Chen <[email protected]>
Signed-off-by: YN Chen <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Tested-by: Chen-Yu Tsai <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The dma would be broken after rmmod flow. There are two different
cases causing this issue.
1. dma access without privilege.
2. hw access sequence borken by another context.
This patch handle both cases to avoid hw crash.
Fixes: 2b9ea5a8cf1bd ("mt76: mt7921: add mt7921_dma_cleanup in mt7921_unregister_device")
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
add .set_sar_specs to allow configuring SAR power limitations on the
frequency ranges from the userland.
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: YN Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Disable chip full reset just during device probing but allow
it during hw restart.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce ds_enable switch to fully control fw deep_sleep capability
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Maximum interval (in seconds) for schedule scan plan supported by
the offload firmware can be U16_MAX.
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move wiphy interface_modes configuration in mt76_alloc_device and
mt76_alloc_phy in order to be overwritten by hw specific code
since some drivers do not support all operating modes (mt7921
supports sta only in the current codebase)
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Return possible error values in mt7921_mac_init routine
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt7921 is mainly used in CE/IoT market so enable runtime-pm by default
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Hw beacon cmd to the mt7921 firmware doesn't only filter out the beacon,
but also performs its own connection monitoring, including periodic
keep-alives to the AP and probing the AP on beacon loss. Will indicate
the host with the event when the firmware detects the connection is lost.
Fixes: 1d8efc741df8 ("mt76: mt7921: introduce Runtime PM support")
Reviewed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: YN Chen <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Enable the deep sleep mode with that firmware is able to trap into
the doze state at runtime to reduce the power consumption further.
The deep sleep mode is not allowed in the STA state transition with
the firmware to have the fast connection experience as we've done in
the full power mode
Reviewed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
As already done for mt7615 and mt7915, enable rx header translation
offload for mt7921 in order to reduce cpu load in the rx path.
Signed-off-by: Lorenzo Bianconi <[email protected]>
