Introduce mt76_mcu data structure to contain common fields between
mt76u_mcu and mt76e_mcu.
Initialize mcu common fields in mt76_alloc_device().
Rely on mt76_mcu in mt76_mcu_rx_event and in mt76_mcu_get_response
in order to reuse them in usb code
Signed-off-by: Lorenzo Bianconi <[email protected]>
Define MT_DRV_RX_DMA_HDR flag in drv_flag in order to not skip rx frame
dma header since new devices (e.g. mt7663u) reports rx frame info in the
usb dma header
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt76u_skb_dma_info utility routine in mt76-usb module in order
to be reused adding mt7663u support
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
7663u devices rely on a different endpoint mapping. Take it into account
in mt76u_alloc_tx routine
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce extended utility routines to read/write data o usb bus. New
devices (e.g. mt7663u) will rely on both upper and lower part of the
register address. Add ext parameter to mt76u_init signature in order to
reuse the code adding mt7663u support.
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add mt76u_alloc_mcu_queue utility routine to allocate mcu hw rx queue.
This is a preliminary patch to support new devices (e.g. mt7663u) that
rely on a hw queue for mcu messages
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Resume all possible rx queues after suspend. This is a preliminary patch
to support mt7663u devices
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add mt76_queue parameter to mt76u_rx_urb_alloc signature since this
routine will be used to allocate urbs for mcu hw queue used by new
chipset generation (e.g. mt7663u). Check sg_max_size in in
mt76u_urb_alloc in order to use linear urb for mcu queue
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt76u_alloc_rx_queue routine to allocate rx hw queue.
This is a preliminary patch to support new devices (e.g. mt7663u) that
rely on a hw queue for mcu messages
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Stop/free all configured rx queues (data/mcu) in
mt76u_stop_rx/mt76u_free_rx. This is a preliminary patch to support new
devices (e.g. mt7663u) that rely on a hw queue for mcu messages
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt76u_free_rx_queue utility routine to free rx hw queue.
This is a preliminary patch to support new devices (e.g. mt7663u) that
rely on a hw queue for mcu messages
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mcu buffer allocation in mt76x2u/mt76x0u drivers since newer
chipsets (e.g. mt7663u) does not rely on synchronous mcu communication
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add queue_id parameter to mt76u_submit_rx_buffers in order to reuse it
adding mt7663u support
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In order to reuse mt76u_complete_rx for both data and mcu rx queue, rely
on mt76_queue as urb context in mt76u_complete_rx. Moreover set usb rx
endoint according to rx queue in mt76u_submit_rx_buf. This is a
preliminary patch to add mt7663u support
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt76_queue parameter to mt76u_refill_rx signature in order to
reuse it for mcu hw rx queue
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rely on mt76_queue pointer in mt76u_get_next_rx_entry in order to add
support for new devices (e.g 7663u) that reports fw events through hw rx
mcu queue
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt76u_process_rx_queue routine to process rx hw queue.
This is a preliminary patch to support new devices (e.g. mt7663u) that
rely on a hw queue for mcu messages
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
New devices (e.g. mt7663u) do not rely on stats workqueue to load tx
statistics but will be reported by the firmware. Check tx_status_data
pointer in mt76u_tx_tasklet in order to reuse tx tasklet for new devices
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
For transferring data over USB the optimal size is endpoint maxpacket.
For my hardware maxpaket for control endpoint is 64 bytes and changing
to this value from 128 bytes further shorten TBTT work time from
3ms to 1ms.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use larger batches for usb copy to speed this operation up. Otherwise it
would be too slow for copying new beacons or broadcast frames over usb.
Assure, that always a multiple of 4 Bytes is copied, as outlined in
850e8f6fbd "mt76: round up length on mt76_wr_copy" from Felix Fietkau.
Signed-off-by: Markus Theil <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is preparation for supporting multiple wiphys per device to support the
concurrent dual-band feature of MT7615D
Signed-off-by: Felix Fietkau <[email protected]>
rate controller and throughput are very sensitive to tx status timing.
In order to improve performances when the system is heavily loaded,
substitute stat_work delayed_work with a regular work_struct and create
a mt76u dedicated workqueue for tx status reporting
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
usb drivers are supposed to communicate using usb_interface instead
mt76x{0,2}u is now registering through usb_device. Fix it by passing
usb_intf device to mt76_alloc_device routine.
Fixes: 112f980ac8926 ("mt76usb: use usb_dev private data")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Tested-By: Zero_Chaos <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This fixes the following checkpatch warnings:
CHECK: Alignment should match open parenthesis
CHECK: No space is necessary after a cast
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
No functional change intended.
Add SPDX identifiers to all remaining files in /mt76.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add mt76_mmio_read_copy routine and the related function pointer in
mt76_bus_ops data structure. mt76_mmio_read_copy will be used to add
BIP_CMAC_128 cipher hw support to mt7615 driver
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Compiler give us guarantees on variables alignment, so use
an variable as buffer when read/write registers and remove
unneeded {put,get}_unaligned.
Signed-off-by: Stanislaw Gruszka <[email protected]>
In contrast to mt76_wr() which we use to program registers,
on mt76_wr_copy() we should not change endian of the data.
Fixes: b40b15e1521f ("mt76: add usb support to mt76 layer")
Signed-off-by: Stanislaw Gruszka <[email protected]>
Fix typo setting urb->transfer_buffer_length in mt76u_fill_rx_sg
Fixes: b40b15e1521f ("mt76: add usb support to mt76 layer")
Fixes: f8f527b16db5 ("mt76: usb: use EP max packet aligned buffer sizes for rx")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Instead of use several 4 bytes usb requests, use full 32 bytes buffer
to copy data to device. With the change we use less requests and copy
exact data size to the device regardless size is multiple of 4 or not.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Compiler give us guaranties on variables alignment, so use
an variable as buffer when read/write registers and remove
unneeded {put,get}_unaligned.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In contrast to mt76_wr() which we use to program registers,
on mt76_wr_copy() we should not change endian of the data.
Fixes: b40b15e1521f ("mt76: add usb support to mt76 layer")
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When beacon length is not a multiple of 4, the beacon could be sent with
the last 1-3 bytes corrupted. The skb data is guaranteed to have enough
room for reading beyond the end, because it is always followed by
skb_shared_info, so rounding up is safe.
All other callers of mt76_wr_copy have multiple-of-4 length already.
Cc: [email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Commit f8f527b16db5 ("mt76: usb: use EP max packet aligned buffer sizes
for rx") breaks A-MSDU support. When A-MSDU is enable the device can
receive frames up to q->buf_size but they will be discarded in
mt76u_process_rx_entry since there is no enough room for
skb_shared_info. Fix the issue reallocating the skb and copying in the
linear area the first 128B of the received frames and in the frag_list
the remaining part
Fixes: f8f527b16db5 ("mt76: usb: use EP max packet aligned buffer sizes for rx")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Remove {out,in}_max_packet from mt76_usb data structure since
they just track last usb endpoint and they are not actually used
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Reduce rx memory footprint allocating just one SG buffer since for the
moment we support just 3839B as maximal size of an A-MSDU.
Introduce different SG_MAX_SIZE definitions for TX and RX sides.
Moreover set q->buf_size to PAGE_SIZE even for SG case.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Set usb buffer size taking into account skb_shared_info in order to
not always copy the first part of received frames if A-MSDU is enabled
for SG capable devices
Signed-off-by: Lorenzo Bianconi <[email protected]>
Commit f8f527b16db5 ("mt76: usb: use EP max packet aligned buffer sizes
for rx") breaks A-MSDU support. When A-MSDU is enable the device can
receive frames up to q->buf_size but they will be discarded in
mt76u_process_rx_entry since there is no enough room for
skb_shared_info. Fix the issue reallocating the skb and copying in the
linear area the first 128B of the received frames and in the frag_list
the remaining part.
Fixes: f8f527b16db5 ("mt76: usb: use EP max packet aligned buffer sizes for rx")
Signed-off-by: Lorenzo Bianconi <[email protected]>
If buffer size is not usb_endpoint_maxp (512 or 1024 bytes) multiple,
usb host driver has to use bounce buffer and copy data. For RX we can
avoid that since we alreay allocate q->buf_size (2kB) buffers and
mt76usb hardware will not fill more data as rx packet size is limited
by network protocol. However add error message if this assumption
somehow will be not true.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
