This helps with locally generated TCP traffic to avoid unnecessary data
copying. Also bump the maximum number of fragments to the limit imposed
by the firmware txp struct.
Signed-off-by: Felix Fietkau <[email protected]>
The hardware simply does not support this in DBDC mode. Remove it from
the HE capabilities.
Signed-off-by: Nicolas Cavallari <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Do not hardcode beamformee 4 space-time streams support, because
DBDC can only support up to 2.
Fixes: 00b2e16e0063 ("mt76: mt7915: add TxBF capabilities")
Signed-off-by: Nicolas Cavallari <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt7915 does not have a per-band number of chains unlike the other chips,
it only has a total number of chains. Yet the current code would
consider the total number as a per-band number.
For example, it would report that a 2x2 + 2x2 DBDC card have 4 chains on
each band and set chainmask to 0b1111 for the first interface and
0b11110000 for the second.
Fixes: 99ad32a4ca3a ("mt76: mt7915: add support for MT7986")
Signed-off-by: Nicolas Cavallari <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
If the nss value is zero in the eeprom, set it to the max.
This eeprom fragment from a mt7915 DBDC shows the problem:
00000190: 24 24 08 00 28 00 00 15 00 00 00 00 00 00 00 00
Fixes: 51a87540232c ("wifi: mt76: mt7915: rework eeprom tx paths and streams init")
Signed-off-by: Nicolas Cavallari <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
For a variant of mt7916, it supports up to 3 tx/rx paths but only 2
spatial streams. This implies that it has one more path to support
beamform. The correct tx/rx path number shall be configured to make sure
beamform works properly.
Fixes: bdaddc92f6b0 ("wifi: mt76: mt7915: deal with special variant of mt7916")
Reviewed-by: Shayne Chen <[email protected]>
Signed-off-by: Howard Hsu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Host triggered and catastrophic event triggered firmware core dumping
for basic firmware issues triage, including state reporting, task/irq
info, function calltrace and MCU memory dump.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Trigger firmware crash and enable full system recovery through debugfs.
This also renames knob "fw_ser" to a clear-cut name "sys_recovery".
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add mt7915_reset() and refactor mt7915_mac_reset_work() to support
full system recovery.
Co-developed-by: Ryder Lee <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Reuse mt7915_dma_disable() to reduce duplicated code.
This is a preliminary patch to enable full system reset.
Co-developed-by: Ryder Lee <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move aggregation stats array per-phy instead of share it between multiple
interfaces. This is a preliminary patch to add mt7996 driver support.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This adds selectable RTC/CTS enablement for each interface.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This reports signal strength of ACK packets from the peer as measured
at each interface.
Tested-by: Shurong Wen <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The MIB INFO command is fetching MIB_BUSY_TIME, MIB_TX_TIME, MIB_RX_TIME and
MIB_OBSS_AIRTIME from the radio and filling out cc_busy, cc_tx, cc_bss_rx
and cc_rx respectively.
busy should be >= tx + rx >= tx + bss_rx but we don’t always quite see this.
Sometimes tx + rx is a bit higher than busy due to inaccurate accounting,
so this patch recalculates numbers to make them more reasonable.
Reported-By: Kevin Schneider <[email protected]>
Tested-by: Kevin Schneider <[email protected]>
Tested-by: Chad Monroe <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Checking the relevant rxd bits for the checksum information only indicates
if the checksum verification was performed by the hardware and doesn't show
actual checksum errors. Checksum errors are indicated in the info field of
the DMA descriptor. Fix packets erroneously marked as CHECKSUM_UNNECESSARY
by checking the extra bits as well.
Those bits are only passed to the driver for MMIO devices at the moment, so
limit checksum offload to those.
Fixes: 2122dfbfd0bd ("mt76: mt7615: add rx checksum offload support")
Fixes: 94244d2ea503 ("mt76: mt7915: add rx checksum offload support")
Fixes: 0e75732764e8 ("mt76: mt7921: enable rx csum offload")
Signed-off-by: Felix Fietkau <[email protected]>
When 802.3 decap offload is enabled, the hardware indicates header translation
failure, whenever either the LLC-SNAP header was not found, or a VLAN header
with an unregcognized tag is present.
In that case, the hardware inserts a 2-byte length fields after the MAC
addresses. For VLAN packets, this tag needs to be removed. However,
for 802.3 LLC packets, the length bytes should be preserved, since there
is no separate ethertype field in the data.
This fixes an issue where the length field was omitted for LLC frames, causing
them to be malformed after hardware decap.
Fixes: 1eeff0b4c1a6 ("mt76: mt7915: fix decap offload corner case with 4-addr VLAN frames")
Reported-by: Chad Monroe <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This reverts commit f17f4864504d754bcbf31e4c89412cdf9946c409.
The reverted commit significantly decreases performance when running
a test where two MT7915 radios have 16 station vdevs each, configured
for AC mode, and transmitting UDP traffic to AP.
Reported-by: Carson Vandegriffe <[email protected]>
Signed-off-by: Ben Greear <[email protected]>
Correct mac timiing settings for different hardware generations.
This improves 40-60Mbps performance.
Fixes: 9aac2969fe5f ("mt76: mt7915: update mac timing settings")
Reported-By: Carson Vandegriffe <[email protected]>
Tested-by: Chad Monroe <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
For MT7915D, correct antenna index should be set to let DFS radar
detection work on the 5 GHz band.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In previous, we only allow user to configure tx antenna mask
contiguously (e.g. 0x3, 0xf).
This patch allows user to configure tx antenna mask interleavingly
(e.g. 0x5, 0x8). By setting proper antenna mask and nss, user can
prioritized the signal of different antennas, which helps to test
their performance in normal mode.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Let the configuration of testmode antenna mask on both band0 and band1
become antenna_mask rather than chainmask. This could simplify the
settings for user and get rid of the conversion when sending fw command.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
A variant of mt7916 supports up to 3 tx/rx paths but with only
2 spatial streams. An example usage of the 3rd path is to server as
an auxiliary for beamforming.
In order to deal with this case, this patch reworks some parts to
correctly use paths or streams.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rework tx paths and streams init part to improve readability, and make
sure that the available tx streams should be smaller than or equal to
the available tx paths.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The value of regidx of rf registers is combined with WF selection and
offset. Extend the WF selection field from 4 to 8 bits since the
adie index should also be specified.
Signed-off-by: Evelyn Tsai <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
According to the tx-free-done documentation, the DW4 can be repeated,
so have to be more careful about how we test for walking off the
end of the array.
Signed-off-by: Ben Greear <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Do not need to check running state before configuring implicit Tx
beamform. It is okay to configure implicit Tx beamform in run time.
Noted that the existing connected stations will be applied for new
configuration only if they reconnected to the interface.
Fixes: 6377b7f330 ("mt76: mt7915: add implicit Tx beamforming support")
Signed-off-by: Howard Hsu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix the error that mcs will be reduced to a range of 0 to 7 in ht mode.
Fixes: 70fd1333cd32 ("mt76: mt7915: rework .set_bitrate_mask() to support more options")
Signed-off-by: Howard Hsu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Given that there's no data coming from network stack for binding flows,
hence driver counts and reports station's statistics directly through
NL80211_STA_INFO_* based on active PPDU based TxS for offloading data.
Apart from that, WA firmware and its offloading engine (SDO) have hardcoded
"2" as PID, so we introduce MT_PACKET_ID_WED to differentiate WED reporting.
Note that PPDU format TxS is mutually exclusive with MT_TXD5_TX_STATUS_HOST.
Co-developed-by: Yi-Chia Hsieh <[email protected]>
Signed-off-by: Yi-Chia Hsieh <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Smatch complains that:
drivers/net/wireless/mediatek/mt76/mt7915/mac.c:428 mt7915_mac_fill_rx()
error: uninitialized symbol 'msta'.
It looks like this was supposed to be initialized to NULL.
Fixes: 0880d40871d1 ("mt76: connac: move mt76_connac2_reverse_frag0_hdr_trans in mt76-connac module")
Signed-off-by: Dan Carpenter <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt76_connac_reg_map structure in mt76-connac module since it
is used by all connac2 chipset. Align structure definitions.
This is a preliminary patch to add mt7990 chipset support.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Report phy_indx in tx_info->hw_queue. This is a preliminary patch to add
newer chipset support
Co-developed-by: Bo Jiao <[email protected]>
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Introduce phy_idx to mt76_wcid structure instead of ext_phy.
This is a preliminary patch to add newer chipset support.
Co-developed-by: Bo Jiao <[email protected]>
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Introduce phys array in mt76_dev structure to reference mt76_phy
supported by the chipset. This is a preliminary patch to introduce
newer chipset support.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Introduce phy_idx mt76_rx_status instead of ext_idx. This is a
preliminary patch to add newer chipset support
Co-developed-by: Bo Jiao <[email protected]>
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Move mt76_connac_init_tx_queues and mt76_connac_tx_cleanup routines
in mt76_connac module. This is a preliminary patch to add mt7990
chipset support.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Previously the code used skb_set_queue_mapping for management or non-bufferable
powersave frames that need to be sent to a different hardware queue.
This can confuse AQL, which expects the value to remain the same until the tx
status report.
The only place that currently uses the altered skb queue mapping is the txwi
write function. Change the code to pass the hardware queue id as a function
parameter instead.
Signed-off-by: Felix Fietkau <[email protected]>
