Overwrite hw queue id for non-bufferable management frames if the hw
support always txq (altxq) in order to be in sync with mac txwi code
Fixes: cdad4874057d ("mt76: mt7615: add dma and tx queue initialization for MT7622")
Fixes: f40ac0f3d3c0 ("mt76: mt7615: introduce mt7663e support")
Suggested-by: Felix Fietkau <[email protected]>
Tested-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
acs and wmm index are swapped in mt7615_queues_acq respect to the hw
design
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Coverage class callback can potentially run in parallel with other
routines (e.g. mt7615_set_channel) that configures timing registers.
Run coverage class callback holding mt76 mutex
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
MT7611N is basically the same as MT7615N, except it only supports 5GHz
It is used by some TP-Link and Mercury wireless routers
Signed-off-by: DENG Qingfang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix hw_scan with ssid_type for specified SSID only
The definition for ssid_type in current firmware is that
ssid_type BIT(2) set actually for specified SSID + wildcard SSID.
ssid_type BIT(2) and ssid_type_ext BIT(0) both set actually for
specified SSID only;
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt7615_mcu_sched_scan_enable should be taken along with
mt7615_mcu_sched_scan_req to have proper scan plans initialization.
Fixes: bd39bd2f00c3 ("mt76: mt7663: introduce WoW with net detect support")
Co-developed-by: Wan-Feng Jiang <[email protected]>
Signed-off-by: Wan-Feng Jiang <[email protected]>
Co-developed-by: Soul Huang <[email protected]>
Signed-off-by: Soul Huang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
switch to per-vif ps support since mt7615 offload firmware can handle it
properly. This patch allows enabling/disabling power-save support on p2p
interface
Tested-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce remain_on_channel support to mt7615 driver if the device is
running offload firmware
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce essential bss information for multiple vifs hw_scan in
mt7615_mcu_uni_add_dev adding the interface
Signed-off-by: Sean Wang <[email protected]>
Co-developed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Differentiate hw scan channel time between passive and active scan
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
All drivers before MT7915 have a limit of 128 WCID entries. Stop relying
on ARRAY_SIZE(dev->mt76.wcid), since it no longer reflects that limit.
Fixes: 49e649c3e0a6 ("mt76: adjust wcid size to support new 802.11ax generation")
Reported-by: kbuild test robot <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix typo defining ps_work in mt7615_register_ext_phy(). This is not a
real issue since 802.11 power save is not yet support by the external phy
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Cancel possible power_save work before stopping the mt7663u interface
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add missing PLE/PSE base register definitions for mt7663u
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Copy key pointer value before running mt76_tx_status_skb_add() in
mt7663u_mac_write_txwi since it will be overwritten setting
mt76_tx_cb for probing frames
Co-developed-by: Johannes Berg <[email protected]>
Signed-off-by: Johannes Berg <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Configure the mcu to scan all available channels if mac80211 does not
provide any frequency list
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix mt7663 eeprom definitions for delta tx power parsing
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt7615_eeprom_get_power_index can return negative error value.
Check mt7615_eeprom_get_power_index return value before using it
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
If device has enabled beacon hw filter rx beacons are not reported to
the host. Introduce beacon_loss mcu event to trigger mac80211 mlme
connection state machine in this configuration.
IEEE80211_VIF_BEACON_FILTER has not set in vif flags since hw beacon
filter is not enabled yet
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Tested on Chromebok by "echo mem to /sys/power/state" to suspend and
then waked up by keyboard keystrokes to resume system.
Signed-off-by: Sean Wang <[email protected]>
Co-developed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce the mt7615_mcu_set_hif_suspend mcu command, which is usually
used to configure the interface including PCIe, USB or SDIO to the right
state during operation suspend / resume.
Signed-off-by: Sean Wang <[email protected]>
Co-developed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce support for passive frequency scanning to mt7615_mcu_hw_scan
Tested-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
For the moment offload firmware supports just one entry in the scheduled
scan plan and so it runs till it is disabled by the userspace.
Do not mark the hw scheduled scan as disabled in mt7615_scan_work
after receiving a scan result
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt7615_check_offload_capability routine to set hw/wiphy
offload capabilities according to the running firmware
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
On top of the EEPROM target power, each rate can also has a power offset.
On many devices, this power offset is used to boost the tx power of lower
rates. Take this into account when parsing rate power.
The assumption here is, that the first rate (OFDM 6M or CCK 1M) has the
highest tx power
Signed-off-by: Felix Fietkau <[email protected]>
Get rid of useless check in mt7663_load_n9 since it is used only for
mt7663 devices
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt7663 firmware v2 is used for embedded devices since it has more completed
features in AP mode.
Add the capability to specify in mt7615 Kconfig which firmware load first
(v3 or v2) and fallback to the other one if the selected firmware fails
to load
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Currently mt7663 devices do not support DBDC so fw events have no info
about it. Fix mt7615_mcu_bss_event that wrongly use bss_idx as DBDC
band_idx while it is vif index.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce sta pointer to mt7615_mcu_add_bss_info signature in order to
avoid sta lookup in mt7615_mcu_bss_basic_tlv routine
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
BMC entry for MT7663 unicmd firmware should be a broadcast/multicast entry,
not a unicast entry, that is GTK rekey offload would rely on.
Fixes: 138860679b2a ("mt76: mt7615: add more uni mcu commands")
Cc: Soul Huang <[email protected]>
Suggested-by: YF Luo <[email protected]>
Co-developed-by: Ryder Lee <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Co-developed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
