To avoid having the hardware potentially write to memory behind stale
descriptors, set the dma-done flag on all of them before cleaning up
allocated rx buffers
Signed-off-by: Felix Fietkau <[email protected]>
The MT7615 firmware needs to know the association id at creation time,
which is unavailable during the transition from notexist to none in
.sta_state.
This can cause a number of issues, probably also breaking powersave
support.
Signed-off-by: Felix Fietkau <[email protected]>
Loading the mcu firmware and waiting for it to boot takes a long time,
which adds a significant amount to the system boot time.
Fix this by running the mcu init from a workqueue and waiting for it to
complete before starting the phy or issuing mcu commands via debugfs
Signed-off-by: Felix Fietkau <[email protected]>
This is only used for testing for now. In the future it will be possible to
enable the second PHY through an proper API via device tree
Signed-off-by: Felix Fietkau <[email protected]>
Beacons and management frames need to explicitly select the alternate tx
queues in order to be sent out on the right phy
Signed-off-by: Felix Fietkau <[email protected]>
Program the RMAC CHFREQ registers to properly indicate the band that the
frames are received on.
Add some sanity checks to the programmed values, because the firmware
programs these registers differently
Signed-off-by: Felix Fietkau <[email protected]>
Move chainmask to struct mt7615_phy and instead of needlessly making the
format similar to values for older chips, make it refer to the actual chain
bits used for the rx/tx path.
This is important for multiple wiphy support, where for a secondary phy,
antenna_mask will start at 0, and chainmask will start at the chain offset
(bit 2)
Signed-off-by: Felix Fietkau <[email protected]>
There are two DFS detectors on the chip. When using 160 MHz channel bandwidth
(not supported in dual-wiphy mode), both are used. Otherwise, one detector is
used per wiphy.
Rework the code to start/stop them separately per phy and to indicate the
radar event on the right phy based on the detector index
Signed-off-by: Felix Fietkau <[email protected]>
Add support for an extra wiphy in mt76_set_channel and mt76_get_survey
This is preparation for supporting multiple wiphys per device to support the
concurrent dual-band feature of MT7615D
Signed-off-by: Felix Fietkau <[email protected]>
This is preparation for supporting multiple wiphys per device to support the
concurrent dual-band feature of MT7615D
Signed-off-by: Felix Fietkau <[email protected]>
This is preparation for supporting multiple wiphys per device to support the
concurrent dual-band feature of MT7615D
Signed-off-by: Felix Fietkau <[email protected]>
This is preparation for supporting multiple wiphys per device to support the
concurrent dual-band feature of MT7615D
Signed-off-by: Felix Fietkau <[email protected]>
This is preparation for supporting multiple wiphys per device to support the
concurrent dual-band feature of MT7615D
Signed-off-by: Felix Fietkau <[email protected]>
This is preparation for supporting multiple wiphys per device to support the
concurrent dual-band feature of MT7615D
On the first wiphy, hw->priv will point to struct mt76_dev, which contains a
struct mt76_phy at the start. For the secondary wiphy, hw->priv will point
to a mt76_phy encapsulated in a driver specific struct
To simplify access to struct mt76_phy members from drivers, the driver specific
device struct is changed to add a union of struct mt76_dev and struct mt76_phy
as the first element
Signed-off-by: Felix Fietkau <[email protected]>
Parse configured {tx,rx} mask from eeprom data instead of just setting it
to four tx-rx streams
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76_get_antenna in mac80211.c in order to be reused by all
drivers. Initialize .get_antenna function pointer for mt76x0, mt7603,
mt7615 and mt76x2u drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix possible out-of-bound access of status rates array in
mt7615_fill_txs/mt7603_fill_txs routines
Fixes: c5211e997eca ("mt76: mt7603: rework and fix tx status reporting")
Fixes: 4af81f02b49c ("mt76: mt7615: sync with mt7603 rate control changes")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Set switch_reason to CH_SWITCH_SCAN_BYPASS_DPD during frequency scanning
in order to disable radar pattern detector
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move interface modes declaration in common code since now mt76
chipsets support all modes (NL80211_IFTYPE_STATION, NL80211_IFTYPE_AP,
NL80211_IFTYPE_MESH_POINT and NL80211_IFTYPE_ADHOC)
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Enable IFTYPE_ADHOC support on 7615 devices. The feature has been tested
using a mt76x2 device as wireless peer.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move SUPPORTS_REORDERING_BUFFER hw property configuration from chip
specific code to mt76_register_device since it is supported by all mt76
drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Convert mt76_is_mmio and mt76_is_usb to rely on mt76_dev instead of
mt76x02_dev since this is a property not strictly related to hw chipset
and it will be more reusable
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/mediatek/mt76/dma.c: In function mt76_dma_rx_fill:
drivers/net/wireless/mediatek/mt76/dma.c:377:6: warning: variable idx set but not used [-Wunused-but-set-variable]
It is not used since commit 17f1de56df05 ("mt76:
add common code shared between multiple chipsets")
Reported-by: Hulk Robot <[email protected]>
Signed-off-by: zhengbin <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
rate controller and throughput are very sensitive to tx status timing.
In order to improve performances when the system is heavily loaded,
substitute stat_work delayed_work with a regular work_struct and create
a mt76u dedicated workqueue for tx status reporting
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
usb drivers are supposed to communicate using usb_interface instead
mt76x{0,2}u is now registering through usb_device. Fix it by passing
usb_intf device to mt76_alloc_device routine.
Fixes: 112f980ac8926 ("mt76usb: use usb_dev private data")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Tested-By: Zero_Chaos <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt76 dma layer is supposed to unmap skb data buffers while keep txwi
mapped on hw dma ring. At the moment mt76 wrongly unmap txwi or does
not unmap data fragments in even positions for non-linear skbs. This
issue may result in hw hangs with A-MSDU if the system relies on IOMMU
or SWIOTLB. Fix this behaviour properly unmapping data fragments on
non-linear skbs.
Fixes: 17f1de56df05 ("mt76: add common code shared between multiple chipsets")
Signed-off-by: Lorenzo Bianconi <[email protected]>
On same device (e.g. U7612E-H1) PCIE_ASPM causes continuous mcu hangs and
instability. Since mt76x2 series does not manage PCIE PS states, first we
try to disable ASPM using pci_disable_link_state. If it fails, we will
disable PCIE PS configuring PCI registers.
This patch has been successfully tested on U7612E-H1 mini-pice card
Tested-by: Oleksandr Natalenko <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Update ewma packet length in mt76x02u_tx_prepare_skb as it is
done for pci counterpart in order to properly estimate tx time on
current channel
Signed-off-by: Lorenzo Bianconi <[email protected]>
Since mt76x0 does not save the phy calibration data it is not necessary
to wait 350ms in mt76x0_phy_calibrate
Tested-by: Sid Hayn <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Felix Fietkau