Report phy_indx in tx_info->hw_queue. This is a preliminary patch to add
newer chipset support
Co-developed-by: Bo Jiao <[email protected]>
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Introduce phy_idx to mt76_wcid structure instead of ext_phy.
This is a preliminary patch to add newer chipset support.
Co-developed-by: Bo Jiao <[email protected]>
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Introduce phys array in mt76_dev structure to reference mt76_phy
supported by the chipset. This is a preliminary patch to introduce
newer chipset support.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Introduce phy_idx mt76_rx_status instead of ext_idx. This is a
preliminary patch to add newer chipset support
Co-developed-by: Bo Jiao <[email protected]>
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Introduce len to __mt76_mcu_msg_alloc signature in order to add the
capability to specify two different value for allocation and copy length.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Introduce __mt76_mcu_msg_alloc utility routine in order to specify gfp
flags for mcu message allocation.
Acked-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
WED support requires using non-coherent DMA, whereas the PCI device might
be configured for coherent DMA.
The WED driver will take care of changing the PCI HIF coherent IO setting
on attach.
Signed-off-by: Felix Fietkau <[email protected]>
MT7915_MAX_INTERFACES is per-band declaration in MT7915/MT7986/MT7916.
Enlarge vif_mask to 64 bits wide, including the bit operation.
Reviewed-by: Shayne Chen <[email protected]>
Signed-off-by: Evelyn Tsai <[email protected]>
Signed-off-by: Bo Jiao <[email protected]>
Introduce __mt76u_init unitility routine and move mt7615 usb bus ops
into mt7615 module in order to allow specifying driver specific
parameter.
This is a preliminary patch to add usb support to mt7921 driver.
Tested-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt7921s driver may receive frames with fragment buffers. If there is a
CTS packet received in monitor mode, the payload is 10 bytes only and
need 6 bytes header padding after RXD buffer. However, only RXD in the
first linear buffer, if we pull buffer size RXD-size+6 bytes with
skb_pull(), that would trigger "BUG_ON(skb->len < skb->data_len)" in
__skb_pull().
To avoid the nonlinear buffer issue, enlarge the RXD size from 128 to
256 to make sure all MCU operation in linear buffer.
[ 52.007562] kernel BUG at include/linux/skbuff.h:2313!
[ 52.007578] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
[ 52.007987] pc : skb_pull+0x48/0x4c
[ 52.008015] lr : mt7921_queue_rx_skb+0x494/0x890 [mt7921_common]
[ 52.008361] Call trace:
[ 52.008377] skb_pull+0x48/0x4c
[ 52.008400] mt76s_net_worker+0x134/0x1b0 [mt76_sdio 35339a92c6eb7d4bbcc806a1d22f56365565135c]
[ 52.008431] __mt76_worker_fn+0xe8/0x170 [mt76 ef716597d11a77150bc07e3fdd68eeb0f9b56917]
[ 52.008449] kthread+0x148/0x3ac
[ 52.008466] ret_from_fork+0x10/0x30
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Check ndesc of q_rx to avoid potential hole in iteration.
This is an intermediate patch to add mt7986 support.
Signed-off-by: Sujuan Chen <[email protected]>
Signed-off-by: Bo Jiao <[email protected]>
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Client mode on DFS channels was broken, because the old code was activating
the DFS detector on radar channels while leaving it in CAC state.
This was caused by making the decision based on the channel radar flag,
instead of hw->conf.radar_enabled.
In order to properly deal with the various corner cases, rip out the state
handling code and replace it with something that's much easier to reason
about.
Signed-off-by: Felix Fietkau <[email protected]>
We don't have to create a separate sdio.xmit_buf buffer for each queue.
Instead, we just need to create one, reuse it across all queues to reduce
memory consumption further.
And then we should take it into account the actual the host and the device
MMC capability to determine what the appropriate xmit_buf_size can be.
Both MT7921S and MT7663 can support up to Tx FIFO size of 0x3fe00 which
means the device can receive 511 blocks of block size 512 in a row from
the host. So if the driver aggregates the frames as many as possible the
the device can support, we can merge multiple MMC requests into a single
one to get rid of the overhead of the handling and synchronizing in those
unnecessary MMC requests and reduce the SDIO lock contention with the
Bluetooth concurrent traffic and finally to have the higher bus
utilization with less idle cycle.
With the patch, it is helpful for WiFi to have steady throughput
performance especially while running Bluetooth concurrently.
Co-developed-by: Deren Wu <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
During heavy loading throughtput test, the RX buffer (128)
would be exhausted and some RX pkts dropped randomly. Increase
buffer size from 128 to 512 (a safer length) to avoid tput degrade
or cmd-timeout problem.
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move wiphy SAR capability configuration in mt76 module and remove
duplicated code.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76_get_sar_power and mt76_init_sar_power in the common code.
This is a preliminary patch to add sar support to mt76x02 drivers.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add support to set SA/DA/BSSID in testmode.
During mass production stage, some test scripts or test equipments need
to set fixed addresses to detect or parse if a test is passed.
Also, MAC setting is necessary for some tx/rx tests with rx filter,
to make sure rx site only receives expected packets.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76_ethtool_worker_info in common code in order to be reused in
mt7921 driver.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to add ethtool stats to mt7921 driver.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Extend mcu_get_nic_capability to obtain tx resource for SDIO device,
MAC address, and PHY capability.
Tested-by: Deren Wu <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add parse_irq to handle that interrupt status structure is
different between mt7663s and mt7921s.
This is a preliminary patch to introduce mt7921s driver
Tested-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move sdio common code in mt76_sdio module.
This is a preliminary patch to support mt7921s devices.
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Export mt76s_alloc_rx_queue and mt76s_alloc_tx utility routines in order
to allow mt7921s driver to configure a different main rx queue.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to create a mt76 debugfs subir for ext-phy.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When received frame is decryped by hardware, CCMP PN is checked by
mt76.
When management frame protection (IEEE 802.11w) is used, we must use
a separate counter for tracking received CCMP packet number for the
management frames. The previously used counter was shared with data
frames and that can cause problems in detecting replays incorrectly
for robust management frames.
Add a new counter just for robust management frames to avoid this
issue.
Signed-off-by: Xing Song <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Each firmware piece with mt7915 and mt7921 do not have the MCU header to
reroute the packet to the internal RAM. So we do not need to consider the
MCU header size in __mt76_mcu_send_firmware.
Move the MCU header overhead calculation to mt76_mcu_send_firmware (for
older chipsets)
Fixes: e57b7901469f ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets")
Fixes: 1c099ab44727 ("mt76: mt7921: add MCU support")
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce __mt76_mcu_send_firmware routine to specify mcu message max
length. This is a preliminary patch to support mt7921s driver.
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Substitute sk_buff_head status_list with spinlock_t status_lock since we
just need it for locking
Tested-by: [email protected]
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove mt76_wcid pointer from mt76_tx_status_check signature since it is
always set to NULL
Tested-by: [email protected]
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce per-wcid idr to manage packet id for txs. This allow fast idr
lookup and skb queueing at the same time.
Tested-by: [email protected]
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Configure 6GHz channels defining mcu channel domain. This is a
preliminary patch to enable 6GHz band on mt7921 devices.
Tested-by: Deren Wu <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add tx-mode (ofdma, ht, vht, HE) histogram,
tx-ru-idx histogram, and tx-bandwidth histogram.
Also add tx attempts and tx success counters.
All of this is per-station.
Signed-off-by: Ben Greear <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Drop MT_DRV_AMSDU_OFFLOAD after introducing IEEE80211_OFFLOAD_ENCAP_ENABLED
flag in mac80211. Driver now checks vif->offload_flags to know encap offload
status of each interface.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt76_register_debugfs_fops routine in order to
define per-driver regs file operations and make sure the
device is up before reading or writing its registers
Fixes: 1d8efc741df8 'mt76: mt7921: introduce Runtime PM support'
Fixes: de5ff3c9d1a2 'mt76: mt7615: introduce pm_power_save delayed work'
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Mesh and ad-hoc interfaces allow users to set mcast rate through
NL80211_ATTR_MCAST_RATE, so rework mt76_default_basic_rate() to
adapt that.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
