Use mt7915_mcu_set_txbf() to reduce global functions. This can be
easily extended to support other TxBF commands in further patches.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
If efuse mode is used, read all values from fw during eeprom init,
which makes it more convinient to check if rf values in efuse are
properly burned.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Firmware functions (SCS, MU ...) also require read-clear phy counters,
hence firmware prepares a global task to read shared fields out to a
shared pool to avoid concurrency. Switch to event format accordingly.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Get per-rate txpower with mcu command. This is the preparation of
co-driver for the next chipset, which has different tmac power registers
but can share this same command.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Thermal cooling device support is added to control the temperature by
throttling the data transmission for the given duration. Throttling is
done by adjusting Tx period by given percentage of time. The thermal
device allows user to configure duty cycle.
Throttling can be disabled by setting the duty cycle to 0. The cooling
device can be found under /sys/class/thermal/cooling_deviceX/.
Corresponding soft link to this device can be found under phy folder
To set duty cycle as 80%,
echo 80 > /sys/class/ieee80211/phy*/cooling_device/cur_state
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This provides userspace with a unified interface, hwmon sysfs, to monitor
temperature in the hardware and can be adapted to system monitoring tools.
For reading temperature, cat /sys/class/ieee80211/phy*/hwmon*/temp1_input
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add runtime configuration for bitrate mask. This update firmware rate
control to add a boundary on top of table to limit the rate selection
for each peer, so when user set bitrates vht-mcs-5 1:9, which actually
means nss = 1 mcs = 0~9. This only applies to data frames as for other
mgmt, mcast, bcast still use legacy rates as it is.
Note that driver does not support GI configuration.
Example:
iw dev wlan0 set bitrates vht-mcs-5 1:9 he-mcs-5 2:7
iw dev wlan0 set bitrates legacy-5 6 he-mcs-5 2:0-11
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove obsoleted codes. This is the preparation for .set_bitrate_mask().
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
"idx" needs to be signed for the error handling to work.
Fixes: 495184ac91bb ("mt76: mt7915: add support for applying pre-calibration data")
Signed-off-by: Dan Carpenter <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Instead of attaching the last reported rate to tx packets, use
ieee80211_tx_status_ext to immediately pass the rate to mac80211 after
receiving it from the firmware.
Preparation for implementing full tx status reporting
Signed-off-by: Felix Fietkau <[email protected]>
Precision %.*s was intended instead of width %*s. The original code
will still print unintended data from beyond the end of skb->data.
Fixes: 665b2c780d63 ("mt76: mt7915: limit firmware log message printk to buffer length")
Signed-off-by: Dan Carpenter <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Clean up the flow of per-rate txpower limit setting to get rid of
duplicate work since it has already been handled by firmware, and set
proper max_power based on different channels and regdomains.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Dump mcu command code in hex and related prefix to help debugging
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When the EEPROM data is read from flash, it can contain pre-calibration
data, which can save calibration time.
Note that group_cal can save 30% bootup calibration time, and dpd_cal can
save 75% channel switching time.
Tested-by: Bo Jiao <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add mmio.c in order to use mt76_bus_ops throughout the driver.
It will be also shared with the future APSoC revision.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Reset wifi subsystem when MCU is already running.
Fixes firmware download failure after soft reboot on systems where the PCIe
reset could not be performed properly.
Signed-off-by: Ryder Lee <[email protected]>
Co-developed-by: Felix Fietkau <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
ieee80211_beacon_get_template() returns NULL when beacon state is disabled.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When disassociating and clearing the BSSID of a repeater entry used by a client
mode interface, the corresponding MAC address entry can get lost too, causing
the client interface to not be able to associate anymore.
Fix this by also refreshing the MAC address when setting the BSSID
Signed-off-by: Felix Fietkau <[email protected]>
Avoid directly updating sinfo->rxrate from firmware since rate_info might
be overwritten by wrong results even mt7915_mcu_get_rx_rate() fails check.
Add more error handlings accordingly.
Fixes: 11553d88d0b9 ("mt76: mt7915: query station rx rate from firmware")
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
For AP and Client mode, the hardware can pass received packets as 802.3 frames
that can be passed to the network stack as-is.
Signed-off-by: Felix Fietkau <[email protected]>
As done for mt76_connac_mcu_alloc_wtbl_req, even if this is not a real
bug since mt7915_mcu_alloc_wtbl_req routine can fails just if nskb is NULL,
always check return value from mt7915_mcu_alloc_wtbl_req in order to avoid
possible future mistake.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
With this patch, TxBF can be run on both bands simultaneously.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
It causes high CPU load on the WA core, which can lead to extra latency when
using many stations. Dropping packets for long queues is managed by mac80211
fq_codel instead
Signed-off-by: Felix Fietkau <[email protected]>
Add support for passing flags for selecting the MCU target and query type
instead of trying to detect it based on the command id
Signed-off-by: Felix Fietkau <[email protected]>
Add ht/vht implicit Tx beamforming support and enable it via debugfs.
Tested-by: Shayne Chen <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch for implicit beamforming support.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Split parameter settings and mcu command update in mt7915_mcu_set_tx().
This is for reusing edca update function in testmode ipg setting.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move chainmask from driver phy to mt76_phy since it is used by all
drivers. This is a preliminary patch to create a common mcu library used
by mt7615 and mt7921 drivers
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The mcs value of HT mode reported by mt7915_mcu_get_rx_rate()
has already been converted to the expected format.
Tested-by: Yiwei Chung <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add testmode support for DBDC NICs (both MT7615D and MT7915D work).
Testmode data and parameters are moved from per-dev to per-phy
for maintaining the value of each band.
Signed-off-by: Shayne Chen <[email protected]>
Acked-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch for DBDC and ipg config support
in testmode.
The wmm_idx of band1 should be configured by this command to
make band1 Tx work normally. Also, for setting ipg, FW needs a
non-empty bss_info structure to do edca parameters update.
Signed-off-by: Shayne Chen <[email protected]>
Acked-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Clang warns in both mt7615 and mt7915:
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:271:9: warning: implicit
conversion from enumeration type 'enum mt76_mcuq_id' to different
enumeration type 'enum mt76_txq_id' [-Wenum-conversion]
txq = MT_MCUQ_FWDL;
~ ^~~~~~~~~~~~
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:278:9: warning: implicit
conversion from enumeration type 'enum mt76_mcuq_id' to different
enumeration type 'enum mt76_txq_id' [-Wenum-conversion]
txq = MT_MCUQ_WA;
~ ^~~~~~~~~~
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:282:9: warning: implicit
conversion from enumeration type 'enum mt76_mcuq_id' to different
enumeration type 'enum mt76_txq_id' [-Wenum-conversion]
txq = MT_MCUQ_WM;
~ ^~~~~~~~~~
3 warnings generated.
drivers/net/wireless/mediatek/mt76/mt7615/mcu.c:238:9: warning: implicit
conversion from enumeration type 'enum mt76_mcuq_id' to different
enumeration type 'enum mt76_txq_id' [-Wenum-conversion]
qid = MT_MCUQ_WM;
~ ^~~~~~~~~~
drivers/net/wireless/mediatek/mt76/mt7615/mcu.c:240:9: warning: implicit
conversion from enumeration type 'enum mt76_mcuq_id' to different
enumeration type 'enum mt76_txq_id' [-Wenum-conversion]
qid = MT_MCUQ_FWDL;
~ ^~~~~~~~~~~~
2 warnings generated.
Use the proper type for the queue ID variables to fix these warnings.
Additionally, rename the txq variable in mt7915_mcu_send_message to be
more neutral like mt7615_mcu_send_message.
Fixes: e637763b606b ("mt76: move mcu queues to mt76_dev q_mcu array")
Link: https://github.com/ClangBuiltLinux/linux/issues/1229
Signed-off-by: Nathan Chancellor <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix the following sparse warning in mt7915_mcu_set_radar_th routine:
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:3154:17: warning: incorrect type in initializer (different base types)
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:3154:17: expected unsigned int [usertype] min_pri
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:3154:17: got restricted __le32 [usertype]
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:3155:17: warning: incorrect type in initializer (different base types)
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:3155:17: expected unsigned int [usertype] max_pri
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:3155:17: got restricted __le32 [usertype]
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:3162:17: warning: incorrect type in initializer (different base types)
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:3162:17: expected unsigned int [usertype] min_stgpr_diff
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:3162:17: got restricted __le32 [usertype]
Fixes: cee236e1489ec ("mt76: mt7915: fix endian issues")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add support for getting rf values from flash.
This is used for some test purposes and products.
If the mtd partition is configured in dts, driver will read from flash
to init eeprom command; if not, still init it with efuse's values.
An example:
&slot0 {
mt7915@0,0 {
reg = <0x0000 0 0 0 0>;
device_type = "pci";
mediatek,mtd-eeprom = <&factory 0x0000>;
};
};
Acked-by: Ryder Lee <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
