Host time is used to calculate the channel active time on mt7603 and mt7615.
Use the same on mt76x02 and move the lock to core code to get rid of some
duplicated code.
Signed-off-by: Felix Fietkau <[email protected]>
Report total rx airtime for valid stations as BSS rx time in survey
mt7615 is left out for now, it will be supported later by reading
hardware counters instead of calculating airtime in software
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76_channel_state() from mt76.h to mac80211.c
Preparation for updating channel state from more places in the drivers/core
Signed-off-by: Felix Fietkau <[email protected]>
Introduce ampdu_stat entry in mt7615 debugfs in order to dump 802.11
aggr cumulative statistics
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt7615_txwi_to_txp utility routine to convert mt76_txwi_cache
into mt7615_txp and remove duplicated code
Signed-off-by: Lorenzo Bianconi <[email protected]>
This fixes the following checkpatch warnings:
CHECK: Alignment should match open parenthesis
CHECK: No space is necessary after a cast
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Refactor mt7615_mac_wtbl_set_key and introduce
the following routines in order to configure wtbl entries
and properly add hw support to BIP_CMAC_128 cipher:
- mt7615_mac_wtbl_update_cipher
- mt7615_mac_wtbl_update_pk
- mt7615_mac_wtbl_update_key
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce channel survey support for mt7615 driver
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce Smart Carrier Sense support in order to tune device
sensitivity according to RTS error rate and False CCA reported by the
radio
Tested-by: Ryder Lee <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This fixes the following checkpatch warnings:
WARNING: Improper SPDX comment style
Fix blank lines.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Hardware supports 4 sets of WMM that should be put to good use.
And fix incorrect queue mapping in mt7615_conf_tx().
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce set_key_cmd and mt76_wcid pointer to mt7615_mac_wtbl_set_key
signature and do not set key to NULL if cmd is DISABLE_KEY.
This is a preliminary patch to add BIP_CMAC_128 hw support to mt7615
driver
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add mt7615_mac_wtbl_set_key routine to configure wtbl key parameter
directly from host cpu. This is a preliminary patch to add BIP_CMAC_128
hw support. Moreover add static qualifier to mt7615_mac_get_key_info
routine
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt7615_mac_wtbl_addr rouinte to compute sta wtbl address.
This is a preliminary patch to update wtbl key directly from host
processor
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to update wtbl key directly from host
processor
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Bufferable management frames need to be put in the data queue, otherwise
they will not be buffered when the receiver is asleep.
Signed-off-by: Felix Fietkau <[email protected]>
The hardware expects MT_TX_RATE_NSS to be filled with the number of
space/time streams. For non-STBC rates, this is equal to nss.
For 1-stream STBC, this needs to be set to 2.
This is relevant for VHT rates only, on HT, the value is derived from MCS
internally.
Signed-off-by: Felix Fietkau <[email protected]>
- Store the previous and current rate set in the driver + the TSF value
at the time of the switch.
- Use the tx status TSF value to determine which rate set needs to be used
as reference.
- Report only short or long GI rates for a single status event, not a mix.
- The hardware reports the last used rate index. Use it along with the
retry count to figure out what rate was used for the first attempt.
- Use the same retry count value for all rate slots to make this calculation
work.
- Derive the probe rate from the current rateset instead of the skb cb
- Do not wait for a status report for the probe frame before removing the
probe rate from the rate table. Do it immediately after it was referenced
in a tx status report.
- Use the first half of the first rate retry budget for the probe rate
in order to avoid using too many retries on that rate
- Switch from lower rates to higher rates more conservatively
- enable hardware rate up/down selection
Signed-off-by: Felix Fietkau <[email protected]>
These values must be initialized to zero, otherwise the hardware could
reuse previous values, especially the rate index
Signed-off-by: Felix Fietkau <[email protected]>
Add hw radar detection support to mt7615 driver in order to
unlock dfs channels on 5GHz band
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fixes gcc '-Wunused-but-set-variable' warnings:
drivers/net/wireless/mediatek/mt76/mt7603/mac.c: In function mt7603_fill_txs:
drivers/net/wireless/mediatek/mt76/mt7603/mac.c:969:5: warning: variable pid set but not used [-Wunused-but-set-variable]
drivers/net/wireless/mediatek/mt76/mt7603/mac.c:961:7: warning: variable final_mpdu set but not used [-Wunused-but-set-variable]
drivers/net/wireless/mediatek/mt76/mt7615/mac.c: In function mt7615_fill_txs:
drivers/net/wireless/mediatek/mt76/mt7615/mac.c:555:5: warning: variable pid set but not used [-Wunused-but-set-variable]
drivers/net/wireless/mediatek/mt76/mt7615/mac.c:552:19: warning: variable final_mpdu set but not used [-Wunused-but-set-variable]
They are never used, so can be removed.
Signed-off-by: YueHaibing <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt7603_get_rate in mac80211.c and rename it to mt76_get_rate
since it is shared between mt7603 and mt7615 drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt7615_insert_ccmp_hdr in mac80211.c and rename it in
mt76_insert_ccmp_hdr since it is shared between mt7603 and mt7615
drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This driver is for a newer generation of MediaTek MT7615 4x4 802.11ac
PCIe-based chipsets, which support wave2 MU-MIMO up to 4 users/group
and also support up to 160MHz bandwidth.
The driver fully supports AP, station and monitor mode.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Roy Luo <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
