mt7915_sta_stats is no longer needed after tx rate reworking.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Report tx rate from tx status packets instead of receving periodic mcu
event. This improves flexibility, accuracy and AQL performance, and
simplifies code flow for better readability.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix the following sparse warning in mt7915_mac_add_txs_skb routine:
drivers/net/wireless/mediatek/mt76/mt7915/mac.c:1235:29:
warning: cast to restricted __le32
drivers/net/wireless/mediatek/mt76/mt7915/mac.c:1235:23:
warning: restricted __le32 degrades to integer
Fixes: 3de4cb1756565 ("mt76: mt7915: add support for tx status reporting")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix the current driver mgmt frame is not respecting the basic rates field
provided by the AP and then unconditionally is using the lowest (1 or 6
Mbps) rate.
For example, if the AP only supported basic rate {24, 36, 48, 54} Mbps,
mt7921 cannot send mgmt frame with the rate not in the group. So,
instead, we pick up the lowest basic rate the AP can support to send.
Fixes: e57b7901469f ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets")
Suggested-by: Ryder Lee <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The iv from RXD is only for TKIP_RSC/CCMP_PN/GCMP_PN, and it needs a
check for CCMP header insertion. Move mt76_cipher_type to mt76.h to
reduce duplicated code.
Signed-off-by: Xing Song <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
- Remove no-op code for queue lock/unlock, which is no longer needed
- Set a missing DMA flag
- Wait for full completion of error recovery before restarting tx
- Schedule IRQ tasklet to ensure that IRQ mask gets written
Signed-off-by: Felix Fietkau <[email protected]>
Firmware functions (SCS, MU ...) also require read-clear phy counters,
hence firmware prepares a global task to read shared fields out to a
shared pool to avoid concurrency. Switch to event format accordingly.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add runtime configuration for bitrate mask. This update firmware rate
control to add a boundary on top of table to limit the rate selection
for each peer, so when user set bitrates vht-mcs-5 1:9, which actually
means nss = 1 mcs = 0~9. This only applies to data frames as for other
mgmt, mcast, bcast still use legacy rates as it is.
Note that driver does not support GI configuration.
Example:
iw dev wlan0 set bitrates vht-mcs-5 1:9 he-mcs-5 2:7
iw dev wlan0 set bitrates legacy-5 6 he-mcs-5 2:0-11
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Instead of attaching the last reported rate to tx packets, use
ieee80211_tx_status_ext to immediately pass the rate to mac80211 after
receiving it from the firmware.
Preparation for implementing full tx status reporting
Signed-off-by: Felix Fietkau <[email protected]>
Move token management in mt76 common module since it is shared between
mt7615, mt7915 and mt7921 drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move token_lock, token and token_count data structures in mt76_dev.
This is a preliminary patch to move token management in mt76 common
module since it is shared by mt7615, mt7915 and mt7921 drivers.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
After DMA reset, tx status information for queued frames will never arrive.
Flush the queue to free skbs immediately instead of waiting for a timeout
Signed-off-by: Felix Fietkau <[email protected]>
In mt7915_mac_reset_work(), make sure freeing skbs after mt7915_dma_reset().
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix ofdm rate index and ldpc setting in rate setting field of tx
descriptor.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add mmio.c in order to use mt76_bus_ops throughout the driver.
It will be also shared with the future APSoC revision.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Frame reception timestamp (low 32-bits) that indicates the value of the
local TSF timer value at the time the first bit of the MAC header in the
received frame (PPDU unit) arriving at the MAC.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In order to properly report MIB counters to mac80211, resets stats in
mt7915_get_stats routine() and hold mt76 mutex accessing MIB counters.
Sum up MIB counters in mt7915_mac_update_mib_stats routine.
Fixes: c6b002bcdf ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets")
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
For AP and Client mode, the hardware can pass received packets as 802.3 frames
that can be passed to the network stack as-is.
Signed-off-by: Felix Fietkau <[email protected]>
Enable hw rx-amsdu de-aggregation support available in 7915 devices.
This is a preliminary patch to enable rx checksum offload
Signed-off-by: Lorenzo Bianconi <[email protected]>
The first pointer in the txp needs to be unmapped as well, otherwise it will
leak DMA mapping entries
Fixes: 27d5c528a7ca ("mt76: fix double DMA unmap of the first buffer on 7615/7915")
Signed-off-by: Felix Fietkau <[email protected]>
For performance reasons, mt7915 supports using 2 PCIE gen1 links on
platforms that don't support gen2.
Add support for using this to move traffic for a second DBDC band onto
a dedicated link
Signed-off-by: Felix Fietkau <[email protected]>
LDPC should be set when bw is larger than 20MHz to make
testmode tx work normally.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move chainmask from driver phy to mt76_phy since it is used by all
drivers. This is a preliminary patch to create a common mcu library used
by mt7615 and mt7921 drivers
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mac_work delayed_work and mac_work_count in mt76_phy since it is
used by all drivers. This is a preliminary patch to create a common mcu
library used by mt7615 and mt7921 drivers
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move per-chip testmode data to mt7915_phy, to properly support
reg_backup and rx status of each band in testmode.
Signed-off-by: Shayne Chen <[email protected]>
Acked-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add testmode support for DBDC NICs (both MT7615D and MT7915D work).
Testmode data and parameters are moved from per-dev to per-phy
for maintaining the value of each band.
Signed-off-by: Shayne Chen <[email protected]>
Acked-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Hardware wouldn't add LLC-SNAP when skb->data_len is 0, which causes
Tx hang, so add a check to drop this kind of packet.
Tested-by: Bo Jiao <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Reset buffering token in mt7915_mac_reset_work() to avoid possible leakege,
which leads to Tx stop after mac reset.
Tested-by: Bo Jiao <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt7915 dbdc support. If dbdc is available, mt7915 primary phy
will work on 2.4GHz band, while secondary one on 5GHz band.
Co-developed-by: Shayne Chen <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Co-developed-by: Ryder Lee <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move hw data queues in mt76_phy from mt76_dev since mt7915 supports per
phy hw queues in dbdc mode
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mcu queue to a dedicated array q_mcu in mt76_dev structure.
This is a preliminary patch to move data queues in mt76_phy and properly
support dbdc
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to move data queues in mt76_phy and properly
support dbdc
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Support testmode rx and display rx statistic by parsing RXV packet
type, which is currently only enabled in testmode.
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Support testmode tx for MT7915A, including tx streams and HE rate
settings.
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
