The maximum command quota of the firmware may be exceeded because the
command to retrieve the quota setting has not been taken into account.
This patch considers not only the quota usage of the command retrieving
quota settings but also limits the total quota usage.
Signed-off-by: Leon Yen <[email protected]>
Signed-off-by: Ming Yen Hsieh <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
- initialize and use per-sta wcid entry instead of vif wcid
- set wcid flags for 4addr/offload
- fix 'newly' argument for vif sta entry update
Signed-off-by: Felix Fietkau <[email protected]>
In some cases MCU messages can get lost. Instead of failing completely,
attempt to recover by re-sending them.
Signed-off-by: Felix Fietkau <[email protected]>
Also report auth/disassoc events, in order to give the driver more control over
handling the station state.
Signed-off-by: Felix Fietkau <[email protected]>
This allows the core code to change the channel. Code deduplication and
preparation for adding scanning code to the core.
Signed-off-by: Felix Fietkau <[email protected]>
When queueing packets, only the MT76_RESET flag of the primary PHY
is checked. If the primary PHY is scanning or changing channels, this can
lead to packet loss for tx on the second PHY.
Fix this by passing the phy to the .tx_queue_skb op and using it to check
the correct flag.
Signed-off-by: Felix Fietkau <[email protected]>
Introduce wed.c in order to collect mt76 wed common codebase used by
mt7915 and mt7996 drivers.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Store usb endpoint in mt76_queue structure and rework q2ep routine.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The ieee80211_queue_work function queues work into the mac80211
local->workqueue, which is widely used for mac80211 internal
work processes. In the mt76 driver, both the mt76-sido-status and
mt76-sdio-net threads enqueue workers to the workqueue with this
function. However, in some cases, when two workers are enqueued
to the workqueue almost simultaneously, the second worker may not
be scheduled immediately and may get stuck for a while.
This can cause timing issues. To avoid these timing
conflicts caused by worker scheduling, replace the worker
with an independent thread.
Fixes: 48fab5bbef40 ("mt76: mt7921: introduce mt7921s support")
Signed-off-by: Wang Zhao <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move WED reset code shared between mt7915 and mt7996 in common module.
This is a preliminary patch to introduce WED reset support for mt7996.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Similar to MT7915, enable Wireless Ethernet Ditpatcher for MT7996
to offload traffic received from the WLAN nic and transmitted on the
LAN one
Co-developed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Co-developed-by: Sujuan Chen <[email protected]>
Signed-off-by: Sujuan Chen <[email protected]>
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Similar to MT7915, enable Wireless Ethernet Ditpatcher for MT7996
to offload traffic received from the LAN nic and transmitted on the
WLAN one
Co-developed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sujuan Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to introduce WED support for mt7996
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mtk_wed_device pointer in mt76_queue structure in order to
configure WED chip.
Get rid of dev parameter in Q_READ and Q_WRITE macros.
Introduce wed parameter to the following routine signatures:
- mt76_init_queue
- mt76_init_tx_queue
This is a preliminary patch to introduce WED support for mt7996 since
mt7996 runs two separate WED chips.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to introduce WED support for mt7996
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to introduce WED support for mt7996
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt76_mmio_wed_offload_enable and mt76_mmio_wed_offload_disable routines
will be reused by mt7996 driver for wed support.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76_mmio_wed_init_rx_buf and mt76_mmio_wed_release_rx_buf routines
in common code.
This is a preliminary patch to introduce WED support for mt7996
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Generilize mt76_get_of_eeprom_from_nvmem to use alternative cell name by
passing the cell name as an arg and expose it.
Rename it to mt76_get_of_data_from_nvmem to better reflect the now more
generic usage.
This is to permit driver to load additional cell, like precal cell.
Tested-by: Shiji Yang <[email protected]>
Signed-off-by: Christian Marangi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Since mt76_get_of_eeprom is not used by mt7915 anymore, unexport it and
make it static again.
Also drop offset arg as it's only supported for MTD and was always set
to 0, hardcode the MTD functio instead.
Signed-off-by: Christian Marangi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Limit support for precal loading for mt7915 only to MTD. Passing data
from DT doesn't support offset and NVMEM require a different cell name
and doesn't support offset hence only MTD way is actually supported.
Rename mt76_get_of_eeprom_from_mtd to mt76_get_of_data_from_mtd as it is
now used for a more generic purpose and export it.
Signed-off-by: Christian Marangi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The 5.9/6GHz channel license of a certain platform device has been
regulated in various countries. That may be difference with standard
Liunx regulatory domain settings. In this case, when .reg_notifier()
called for regulatory change, mt792x chipset should update the channel
usage based on clc or dts configurations.
Channel would be disabled by following cases.
* clc report the particular UNII-x is disabled.
* dts enabled and the channel is not configured.
Signed-off-by: Ming Yen Hsieh <[email protected]>
Co-developed-by: Deren Wu <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The variable band should be determined by the ieee80211_chanctx_conf when
the driver is a kind of chanctx one e.g mt7921 and mt7922 driver so we
added the extension to mt76_connac2_mac_tx_rate_val by distinguishing if
it can support chanctx to fix the incorrect rate pickup.
Fixes: 41ac53c899bd ("wifi: mt76: mt7921: introduce chanctx support")
Signed-off-by: Sean Wang <[email protected]>
Reviewed-by: David Ruth <[email protected]>
Tested-by: David Ruth <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move struct ieee80211_chanctx_conf up to struct mt76_vif to allow the
connac2 library can access the struct ieee80211_chanctx_conf * member in
struct mt76_vif.
Signed-off-by: Sean Wang <[email protected]>
Reviewed-by: David Ruth <[email protected]>
Tested-by: David Ruth <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add eht field in struct mt76_power_limits for 802.11be power config.
The function stack size would be too big by eht adding in structure,
we also refactor mt76_connac_mcu_rate_txpower_band() to take dynamic
allocated memory instead.
This is a preliminary patch to support mt7925 driver.
Co-developed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add support to report eht rx rate.
Note that extended fields for eht in mt76_rx_status will make the struct
size exceed the cb size, so make nss and band share the same u8.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When drv_tx calls race against local tx scheduling, the queue fill status checks
can potentially race, leading to dma queue entries being overwritten.
Fix this by deferring packets from drv_tx calls to the tx worker, in order to
ensure that all regular queue tx comes from the same context.
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to introduce mt76_connac3 mac library used
by WiFi7 chipsets (e.g. mt7996).
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
ampdu_state field is used by most of the drivers, so move it in
mt76_wcid structure.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
poll_list field is used by most of the drivers, so move it in mt76_wcid
structure.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
sta_poll_list and sta_poll_lock are used by most of the drivers, so move
them in mt76_dev structure.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The stats are clear-on-read, which makes it very difficult for tools
to adequately deal with wrapped stats and with keeping good totals.
So, accumulate these values when they are read from the firmware/radio
and present totals to user-space.
Signed-off-by: Ben Greear <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mib_stats structure is shared by mostly all chipsets. Move it to shared
code.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
PPDU TxS can only report MPDU count whereas mac80211 requires MSDU scale
(NL80211_STA_INFO_TX_PACKETS), so switch to get MSDU counts from WA
statistic.
Note that mt7915 WA firmware only counts tx_packet for WED path, so driver
needs to take care of host path additionally.
Fixes: 43eaa3689507 ("wifi: mt76: add PPDU based TxS support for WED device")
Co-developed-by: Ryder Lee <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
irq_tasklet struct is used by most of the drivers (e.g. mt7915, mt7921,
mt7615, mt7663 and mt7996) so move it in common code.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
