Since mt7925_mac_sta_add publishes wcid, add publish check in mt76_sta_add
to avoid reinitializing the wcid->poll_list.
Found dev->sta_poll_list corruption when using mt7925 and 7.1-rc4.
According to the corruption information, prev->next was changed to itself.
wlan0: disconnect from AP 90:fb:5d:94:8b:e3 for new auth to 90:fb:5d:94:8b:e2
wlan0: authenticate with 90:fb:5d:94:8b:e2 (local address=84:9e:56:9c:7e:6b)
wlan0: send auth to 90:fb:5d:94:8b:e2 (try 1/3)
slab kmalloc-8k start ffff8c80958a6000 pointer offset 4160 size 8192
list_add corruption. prev->next should be next (ffff8c808a7488f8), but was ffff8c80958a7040. (prev=ffff8c80958a7040).
mt76_wcid_add_poll+0x95/0xd0 [mt76]
mt7925_mac_add_txs.part.0+0xa5/0xe0 [mt7925_common]
mt7925_rx_check+0xa7/0xc0 [mt7925_common]
mt76_dma_rx_poll+0x50d/0x790 [mt76]
mt792x_poll_rx+0x52/0xe0 [mt792x_lib]
Signed-off-by: Jiajia Liu <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
When associated with a nontransmitted BSS in an MBSSID set, the beacon
frame's BSSID (addr3) contains the transmitting AP's BSSID, not the
station's associated BSSID. The beacon matching in mt76_rx_beacon_iter()
only compared against link_conf->bssid, so beacons were never matched,
causing false beacon loss reports.
Add a fallback check against link_conf->transmitter_bssid when
link_conf->nontransmitted is set, mirroring mac80211's
ieee80211_rx_our_beacon() logic.
Signed-off-by: Felix Fietkau <[email protected]>
ieee80211_tx_prepare_skb already frees the skb internally when
invoke_tx_handlers fails, so freeing it again in the caller leads to a
double-free / NULL pointer dereference in skb_release_data.
Signed-off-by: Felix Fietkau <[email protected]>
Prevent mt76_scan_rx_beacon() in softirq from requeuing scan_work
after cancel_delayed_work_sync() returns in mt76_abort_scan(). Without
synchronization, the beacon handler can observe beacon_wait as true
and requeue scan_work between the cancel and the memset in
mt76_scan_complete(), leading to a NULL pointer dereference when
scan_work runs against zeroed scan state.
Introduce scan_lock (placed outside the scan struct to survive the
memset) to make the beacon handler's check-and-queue atomic with
respect to abort_scan's clear of beacon_wait. This eliminates the
race with a single cancel_delayed_work_sync() call.
Signed-off-by: Felix Fietkau <[email protected]>
With chanctx drivers using hardware scan or remain-on-channel,
mac80211 does not know when the radio goes off-channel, which breaks
its software beacon loss detection.
Implement per-link beacon monitoring in the driver. Track the last
beacon timestamp per link and check for beacon loss periodically from
the mac_work handler.
Beacon monitoring is initialized on association and on late link
activation, and cleared on disassociation. The beacon_mon_last
timestamp is reset when returning from offchannel and after channel
switches to prevent false beacon loss detection.
Signed-off-by: Felix Fietkau <[email protected]>
After flushing software-pending frames to DMA, mt76_has_tx_pending()
only checks DMA ring q->queued. For token-based drivers, q->queued is
decremented at DMA consumption, but firmware may not have transmitted
the frame yet. Waiting for all tokens is not feasible because data
frames may be stuck in firmware powersave/aggregation queues.
Track PSD queue tokens (firmware ALTX) per phy using an atomic counter.
These frames are sent by firmware immediately without PS buffering, so
the counter reliably reaches zero after transmission.
Increment the counter in mt76_token_consume() and decrement it in
mt76_token_release(), only for PSD queue tokens. Include the counter
in mt76_has_tx_pending() so channel switch waits for firmware TX
completion of management and nullfunc frames.
mt7615 (uses mt76_token_get/put) and non-token drivers are unaffected
as they never call mt76_token_consume/release.
Signed-off-by: Felix Fietkau <[email protected]>
mt76_tx() queues frames on wcid->tx_pending for async processing by
tx_worker. In __mt76_set_channel(), the worker gets disabled before it
may have run, and the subsequent wait only checks DMA ring queues, not
the software pending list. This means frames like nullfunc PS frames
from mt76_offchannel_notify() may never be transmitted on the correct
channel.
Fix this by running mt76_txq_schedule_pending() synchronously after
disabling the tx_worker but before setting MT76_RESET, which would
otherwise cause mt76_txq_schedule_pending_wcid() to bail out.
Signed-off-by: Felix Fietkau <[email protected]>
Since mt76 uses chanctx, mac80211 does not send nullfunc power save
notifications when the driver goes offchannel for scan or ROC.
Add mt76_offchannel_notify() to send nullfunc PM=1 before going
offchannel and PM=0 after returning, so that the AP can buffer
frames during the absence.
For MLO, iterate all vif links on the phy and set
IEEE80211_TX_CTRL_MLO_LINK so that the driver's tx_prepare_skb
resolves the correct per-link wcid.
Signed-off-by: Felix Fietkau <[email protected]>
Having this unset breaks remain-on-channel and mgmt TX.
Move setting it to mt76 core to keep it in one place.
Fixes: 69d54ce7491d0 ("wifi: mt76: mt7996: switch to single multi-radio wiphy")
Signed-off-by: Felix Fietkau <[email protected]>
In order to recycle skbs in the page_pool "hot" cache in
napi_pp_put_page routine, set napi pointer for MMIO devices in
mt76_create_page_pool().
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt76_wcid_cleanup() was not removing wcid entries from sta_poll_list
before mt76_reset_device() reinitializes the master list. This leaves
stale pointers in wcid->poll_list, causing list corruption when
mt76_wcid_add_poll() later checks list_empty() and tries to add the
entry back.
The fix adds proper cleanup of poll_list in mt76_wcid_cleanup(),
matching how tx_list is already handled. This is similar to what
mt7996_mac_sta_deinit_link() already does correctly.
Fixes list corruption warnings like:
list_add corruption. prev->next should be next (ffffffff...)
Signed-off-by: Zac Bowling <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Currently, per-radio attributes are set on per-phy basis, i.e., all the
radios present in a wiphy will take attributes values sent from user. But
each radio in a wiphy can get different values from userspace based on
its requirement.
To extend support to set per-radio attributes, add support to get radio
index from userspace. Add an NL attribute - NL80211_ATTR_WIPHY_RADIO_INDEX,
to get user specified radio index for which attributes should be changed.
Pass this to individual drivers, so that the drivers can use this radio
index to change per-radio attributes when necessary. Currently, per-radio
attributes identified are:
NL80211_ATTR_WIPHY_TX_POWER_LEVEL
NL80211_ATTR_WIPHY_ANTENNA_TX
NL80211_ATTR_WIPHY_ANTENNA_RX
NL80211_ATTR_WIPHY_RETRY_SHORT
NL80211_ATTR_WIPHY_RETRY_LONG
NL80211_ATTR_WIPHY_FRAG_THRESHOLD
NL80211_ATTR_WIPHY_RTS_THRESHOLD
NL80211_ATTR_WIPHY_COVERAGE_CLASS
NL80211_ATTR_TXQ_LIMIT
NL80211_ATTR_TXQ_MEMORY_LIMIT
NL80211_ATTR_TXQ_QUANTUM
By default, the radio index is set to -1. This means the attribute should
be treated as a global configuration. If the user has not specified any
index, then the radio index passed to individual drivers would be -1. This
would indicate that the attribute applies to all radios in that wiphy.
Signed-off-by: Roopni Devanathan <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Johannes Berg <[email protected]>
Move mt76_abort_scan routine out of mt76_reset_device() in order to
avoid a possible deadlock since mt76_reset_device routine is running
with mt76 mutex help and mt76_abort_scan_complete() can grab mt76 mutex
in some cases.
Fixes: b36d55610215a ("wifi: mt76: abort scan/roc on hw restart")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Tested-by: Ben Greear <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Add the NPU generic layer in mt76 module. NPU will be used to enable
traffic forward offloading between the MT76 NIC and the Airoha ethernet one
available on the Airoha EN7581 SoC using Netfilter Flowtable APIs.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
MediaTek has asked to switch from the ISC license to BSD-3-Clause-Clear,
in order to improve clarity and the legal integrity of the code.
The BSD-3-Clause license includes the "no endorsement" clause, which is
important for protecting the reputation of the original authors and
contributors by preventing unauthorized use of their names for endorsement
purposes.
This clause is absent in the BSD-2-Clause license, which is more permissive
but lacks this specific protection.
This change also cleans up the license of some Kconfig/Makefile files,
which were accidentally marked as GPL.
The GPL 2.0 remains in use on mt76x0, as well as two source files in mt7615
for which the license situation still needs to be clarified.
Signed-off-by: Felix Fietkau <[email protected]>
Set UP in skb->priority to allow DSCP Learning at upper layers
Signed-off-by: Howard Hsu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Avoid leaking them or keeping the wcid on the tx list
Fixes: 0b3be9d1d34e ("wifi: mt76: add separate tx scheduling queue for off-channel tx")
Signed-off-by: Felix Fietkau <[email protected]>
Since stations are recreated from scratch, all lists that wcids are added
to must be cleared before calling ieee80211_restart_hw.
Set wcid->sta = 0 for each wcid entry in order to ensure that they are
not added again before they are ready.
Signed-off-by: Felix Fietkau <[email protected]>
ML interfaces can have multiple affiliated links to it and
hence there is a need to report tx power of specified link
rather deflink.
Add changes to report tx power of requested link from mac80211,
also pass link id as an argument in get_tx_power op so that supported
drivers can use it to report link's tx power.
Co-developed-by: Aaradhana Sahu <[email protected]>
Signed-off-by: Aaradhana Sahu <[email protected]>
Signed-off-by: Rameshkumar Sundaram <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Johannes Berg <[email protected]>
One variant of MT7992 has 5 TX paths, so extend the power delta function
to support it. Also, rename nss_delta to path_delta since the value is
based on the number of TX paths rather tha the number of spatial streams.
(path delta [0.5 dBm] = 10 * log(path number) [dBm] * 2)
Co-developed-by: StanleyYP Wang <[email protected]>
Signed-off-by: StanleyYP Wang <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Check if available_antennas_tx and available_antennas_rx are already set
during the per-chip initialization phase; otherwise, they could be
overwritten with incorrect values.
Fixes: 69d54ce7491d ("wifi: mt76: mt7996: switch to single multi-radio wiphy")
Signed-off-by: Shayne Chen <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt7996_sta_state routine in order to initialize wcid structure
in mt7996 codebase. This is a preliminary patch to enable MLO support in
MT7996 driver.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Fixes linked list management issues during restart, where sta entries
can be recreated and reinitialized while still in the poll list, triggering
kernel warnings.
Signed-off-by: Felix Fietkau <[email protected]>
Avoids sending packets too early
Fixes: 0b3be9d1d34e ("wifi: mt76: add separate tx scheduling queue for off-channel tx")
Signed-off-by: Felix Fietkau <[email protected]>
This allows a driver using the generic channel context functions to
temporarily switch to another channel for off-channel rx/tx.
Signed-off-by: Felix Fietkau <[email protected]>
This adds an implementation for the chanctx functions, which can be used
by multi-channel capable drivers. Preparation for adding MLO support.
Signed-off-by: Felix Fietkau <[email protected]>
Preparation for supporting multiple radios on a single wiphy on devices
where firmware does not support actual hardware scanning.
This is also a prerequisite for full MLO support
Co-developed-by: Peter Chiu <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Co-developed-by: Michael-CY Lee <[email protected]>
Signed-off-by: Michael-CY Lee <[email protected]>
Co-developed-by: Shayne Chen <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
- initialize and use per-sta wcid entry instead of vif wcid
- set wcid flags for 4addr/offload
- fix 'newly' argument for vif sta entry update
Signed-off-by: Felix Fietkau <[email protected]>
Also report auth/disassoc events, in order to give the driver more control over
handling the station state.
Signed-off-by: Felix Fietkau <[email protected]>
This allows the core code to change the channel. Code deduplication and
preparation for adding scanning code to the core.
Signed-off-by: Felix Fietkau <[email protected]>
Do not assume that the first phy has 2 GHz support.
Check sband->band instead of accessing dev->phy.sband_2g.
Signed-off-by: Felix Fietkau <[email protected]>
