Correct mac timiing settings for different hardware generations.
This improves 40-60Mbps performance.
Fixes: 9aac2969fe5f ("mt76: mt7915: update mac timing settings")
Reported-By: Carson Vandegriffe <[email protected]>
Tested-by: Chad Monroe <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
For MT7915D, correct antenna index should be set to let DFS radar
detection work on the 5 GHz band.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In previous, we only allow user to configure tx antenna mask
contiguously (e.g. 0x3, 0xf).
This patch allows user to configure tx antenna mask interleavingly
(e.g. 0x5, 0x8). By setting proper antenna mask and nss, user can
prioritized the signal of different antennas, which helps to test
their performance in normal mode.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Let the configuration of testmode antenna mask on both band0 and band1
become antenna_mask rather than chainmask. This could simplify the
settings for user and get rid of the conversion when sending fw command.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
A variant of mt7916 supports up to 3 tx/rx paths but with only
2 spatial streams. An example usage of the 3rd path is to server as
an auxiliary for beamforming.
In order to deal with this case, this patch reworks some parts to
correctly use paths or streams.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rework tx paths and streams init part to improve readability, and make
sure that the available tx streams should be smaller than or equal to
the available tx paths.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The value of regidx of rf registers is combined with WF selection and
offset. Extend the WF selection field from 4 to 8 bits since the
adie index should also be specified.
Signed-off-by: Evelyn Tsai <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
According to the tx-free-done documentation, the DW4 can be repeated,
so have to be more careful about how we test for walking off the
end of the array.
Signed-off-by: Ben Greear <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Do not need to check running state before configuring implicit Tx
beamform. It is okay to configure implicit Tx beamform in run time.
Noted that the existing connected stations will be applied for new
configuration only if they reconnected to the interface.
Fixes: 6377b7f330 ("mt76: mt7915: add implicit Tx beamforming support")
Signed-off-by: Howard Hsu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix the error that mcs will be reduced to a range of 0 to 7 in ht mode.
Fixes: 70fd1333cd32 ("mt76: mt7915: rework .set_bitrate_mask() to support more options")
Signed-off-by: Howard Hsu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Given that there's no data coming from network stack for binding flows,
hence driver counts and reports station's statistics directly through
NL80211_STA_INFO_* based on active PPDU based TxS for offloading data.
Apart from that, WA firmware and its offloading engine (SDO) have hardcoded
"2" as PID, so we introduce MT_PACKET_ID_WED to differentiate WED reporting.
Note that PPDU format TxS is mutually exclusive with MT_TXD5_TX_STATUS_HOST.
Co-developed-by: Yi-Chia Hsieh <[email protected]>
Signed-off-by: Yi-Chia Hsieh <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Smatch complains that:
drivers/net/wireless/mediatek/mt76/mt7915/mac.c:428 mt7915_mac_fill_rx()
error: uninitialized symbol 'msta'.
It looks like this was supposed to be initialized to NULL.
Fixes: 0880d40871d1 ("mt76: connac: move mt76_connac2_reverse_frag0_hdr_trans in mt76-connac module")
Signed-off-by: Dan Carpenter <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt76_connac_reg_map structure in mt76-connac module since it
is used by all connac2 chipset. Align structure definitions.
This is a preliminary patch to add mt7990 chipset support.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Report phy_indx in tx_info->hw_queue. This is a preliminary patch to add
newer chipset support
Co-developed-by: Bo Jiao <[email protected]>
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Introduce phy_idx to mt76_wcid structure instead of ext_phy.
This is a preliminary patch to add newer chipset support.
Co-developed-by: Bo Jiao <[email protected]>
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Introduce phys array in mt76_dev structure to reference mt76_phy
supported by the chipset. This is a preliminary patch to introduce
newer chipset support.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Introduce phy_idx mt76_rx_status instead of ext_idx. This is a
preliminary patch to add newer chipset support
Co-developed-by: Bo Jiao <[email protected]>
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Move mt76_connac_init_tx_queues and mt76_connac_tx_cleanup routines
in mt76_connac module. This is a preliminary patch to add mt7990
chipset support.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Previously the code used skb_set_queue_mapping for management or non-bufferable
powersave frames that need to be sent to a different hardware queue.
This can confuse AQL, which expects the value to remain the same until the tx
status report.
The only place that currently uses the altered skb queue mapping is the txwi
write function. Change the code to pass the hardware queue id as a function
parameter instead.
Signed-off-by: Felix Fietkau <[email protected]>
Since an in-band discovery frame is offloaded by MCU,
here we enlarge the command size to accommodate the additional content.
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Money Wang <[email protected]>
Signed-off-by: MeiChia Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Set EXTRA_INFO_NEW for the first time only to prevent adding the same
starec entry, otherwise the entry might be removed in fw.
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
We do not modify ieee80211_ops pointers so we do not need to copy them.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix the issue that the measured inter packet gap didn't fit its
setting value.
Fixes: c2d3b1926f30 ("mt76: mt7915: add support for ipg in testmode")
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76_connac2_mcu_fill_message routine in shared module in order to
reuse it for mt7921 and mt7915e drivers. This is a preliminary patch to
add mt7990 driver support.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to add mt7990 chipset support.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
As for mt7921 and mt7615 drivers, rely on mt76_connac_tx_free data
structure in mt7915e driver.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt7615_txp_skb_unmap in shared code and reuse it in mt7915e and
mt7921e driver.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Since now txp structures are in common code we can reuse
mt76_connac_tx_complete_skb routine in mt7921e, mt7915e and mt7615e
drivers.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Since mt76_connac_fw_txp struct is shared between mt7615e, mt7915e and
mt7921e, move it in mt76_connac module.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove unnecessary new line in mt7915_mac_write_txwi routine.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
After initially establishing a connection, it can produce multi-second latency
spikes and tx hangs when pushing traffic.
It should work better for MT7916 and MT7986, so leave it enabled there
Signed-off-by: Felix Fietkau <[email protected]>
Rely on mt76_connac2_mac_fill_rx_rate routine in mt7921 driver.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt76_connac2_reverse_frag0_hdr_trans routine is shared between mt7921
and mt7915e drivers.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
HE radiotap parsing code is shared between connac2 devices.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76_connac2_mac_add_txs_skb in mt76-connac module since it is
shared between connac2 devices (mt7921 and mt7915)
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mac_write_txwi code is shared between connac2 devices (mt7915 and
mt7921). Move it in connac module.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to share connac2 mac txwi code.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to share txwi configuration code.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
According IEEE Std 802.11-2020, its definition is:
Indicates whether the STA is capable of interpreting the Extended NSS BW
Support subfield of the VHT Capabilities Information field.
Some APs, such as Xiaomi AX6000, would check this one for BW settings.
mt76 driver can get max BW capability only if the this field is confgured
properly.
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Ming Yen Hsieh <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76_connac2_load_patch utility routine in mt76_connac module since
it is shared between mt7921 and mt7915. This is a preliminary patch to
support mt7902e driver.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76_connac2_load_ram utility routine in mt76_connac module since
it is shared between mt7921 and mt7915. This is a preliminary patch to
support mt7902e driver.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76_connac2 fw structures in connac module since they are shared
between mt7921 and mt7915 drivers. This is a preliminary patch to add
mt7902e support.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
napi_schedule() can call __raise_softirq_irqoff(), which can perform softirq
handling, so it must not be called in a pure process context with BH enabled.
Signed-off-by: Felix Fietkau <[email protected]>
