Add support to send larger packet in testmode to meet requirements
of some test cases.
The limit of max packet size is determined based on tx rate mode setting.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Support to set a special tx state in testmode: continuous tx,
which is used for sending tx without time gap.
Note that continuous tx mode doesn't send real packets, instead, it's
pure phy signal, and the waveform can be observed by instrument.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Originally, tx queued limit is set to 1000 to prevent from running out
of tx token. If a new testmode tx is triggered while the previous one
hasn't finished yet, we'll wait a period of time until tx_done equals to
tx_queued. Normally, current queued limit can finish in 10 seconds.
However, if ipg is configured to a larger value, less than 1000 packets
can be done in the default timeout period, which may lead to a crash
when a new testmode tx triggered.
To deal with this, make tx queued limit dynamically adjusted according
to ipg value.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add attributes for setting tx inter-packet gap (ipg), duty cycle, and
transmission time in testmode.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add spatial extension (spe) index as a configurable parameter in testmode.
This is used for specifically configuring TX path, such as different
WF TX priority, number of antennas and spatial streams.
If spe_idx is not set, TX path depends on tx_antenna_mask; otherwise,
both spe_idx and tx_antenna_mask are referenced to decide TX path.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Extend enum mt76_testmode_tx_mode to support various HE rate modes.
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]> [update tools/]
Prepare for setting different LTF (1x, 2x, and 4x) and GI (0.8us,
1.6us, 3.2us) combinations in HE rate mode.
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]> [update tools/]
Add the parameter to control STBC function in testmode.
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]> [update tools/]
Support to display snr value when dumping rx statistics.
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]> [update tools/]
Change ib_rssi and wb_rssi into array type, since they could be reported
by per-antenna.
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]> [update tools/]
This can be used for calibration in the manufacturing process.
It supports sending a configurable number of packets with a specific rate
and configurable tx power levels / antenna settings.
It also supports receiving packets and showing some statistics, including
packet counters and detailed RSSI information.
It will only be compiled in if CONFIG_NL80211_TESTMODE is enabled
Signed-off-by: Felix Fietkau <[email protected]>
