Add mmio.c in order to use mt76_bus_ops throughout the driver.
It will be also shared with the future APSoC revision.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Frame reception timestamp (low 32-bits) that indicates the value of the
local TSF timer value at the time the first bit of the MAC header in the
received frame (PPDU unit) arriving at the MAC.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In order to properly report MIB counters to mac80211, resets stats in
mt7915_get_stats routine() and hold mt76 mutex accessing MIB counters.
Sum up MIB counters in mt7915_mac_update_mib_stats routine.
Fixes: c6b002bcdf ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets")
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
For performance reasons, mt7915 supports using 2 PCIE gen1 links on
platforms that don't support gen2.
Add support for using this to move traffic for a second DBDC band onto
a dedicated link
Signed-off-by: Felix Fietkau <[email protected]>
With this patch, TxBF can be run on both bands simultaneously.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add ht/vht implicit Tx beamforming support and enable it via debugfs.
Tested-by: Shayne Chen <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Split parameter settings and mcu command update in mt7915_mcu_set_tx().
This is for reusing edca update function in testmode ipg setting.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move chainmask from driver phy to mt76_phy since it is used by all
drivers. This is a preliminary patch to create a common mcu library used
by mt7615 and mt7921 drivers
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mac_work delayed_work and mac_work_count in mt76_phy since it is
used by all drivers. This is a preliminary patch to create a common mcu
library used by mt7615 and mt7921 drivers
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move per-chip testmode data to mt7915_phy, to properly support
reg_backup and rx status of each band in testmode.
Signed-off-by: Shayne Chen <[email protected]>
Acked-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add support for getting rf values from flash.
This is used for some test purposes and products.
If the mtd partition is configured in dts, driver will read from flash
to init eeprom command; if not, still init it with efuse's values.
An example:
&slot0 {
mt7915@0,0 {
reg = <0x0000 0 0 0 0>;
device_type = "pci";
mediatek,mtd-eeprom = <&factory 0x0000>;
};
};
Acked-by: Ryder Lee <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Reset buffering token in mt7915_mac_reset_work() to avoid possible leakege,
which leads to Tx stop after mac reset.
Tested-by: Bo Jiao <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
MCU expects to set WLAN_CIPHER_SUITE_CCMP and WLAN_CIPHER_SUITE_AES_CMAC
at the same time, so adding an intermediate buffer for batch update.
Tested-by: Sujuan Chen <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt7915 automatically detects dbdc feature so drop debugfs knob.
Move if_comb, mt7915_rates, if_limits structs and mt7915_regd_notifier(),
mt7915_init_wiphy() routines at the begging of init.c in order to make
mt7915_register_ext_phy routine static
Co-developed-by: Shayne Chen <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Co-developed-by: Ryder Lee <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt7915 dbdc support. If dbdc is available, mt7915 primary phy
will work on 2.4GHz band, while secondary one on 5GHz band.
Co-developed-by: Shayne Chen <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Co-developed-by: Ryder Lee <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Make mt7915_eeprom_read routine static since it is used only in eeprom.c
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Support testmode rx and display rx statistic by parsing RXV packet
type, which is currently only enabled in testmode.
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Support testmode tx for MT7915A, including tx streams and HE rate
settings.
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When per-packet rate reporting is enabled, the hardware can get stuck under
some conditions. It self-recovers quickly, but in practice this leads to
reduced performance.
In order to avoid running into this issue, disable per-packet rate reporting
by default and query the rx rate from firmware instead, unless monitor mode
is enabled.
Signed-off-by: Felix Fietkau <[email protected]>
Read per-stream measurements every 100 ms and build a simple moving average.
Tested-by: Shayne Chen <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When looking for a MAC address slot, start by using main BSSID slots 1-3,
afterwards use 16 repeater mode BSSID slots, then start using the slots
usually used for AP mode.
This search order should prevent unnecessary conflicts with AP mode interfaces
on the same PHY
Signed-off-by: Felix Fietkau <[email protected]>
Compared to mac80211 ACs, MT7915 queue numbers are in reverse order
There is no need for the defensive WARN_ON_ONCE, so we can simplify
the function to avoid the array lookup
Signed-off-by: Felix Fietkau <[email protected]>
Since DMA completion does not imply tx completion, it makes more sense to
poll for airtime from mt7915_mac_tx_free.
Reduce the runtime of the function by moving all items from dev->sta_poll_list
to a local list once and process any stations that were added afterwards
on the next run
Signed-off-by: Felix Fietkau <[email protected]>
Use the txwi data as primary source information to avoid touching skb data
Use bitfield instead of state variable + spinlock
Signed-off-by: Felix Fietkau <[email protected]>
Queueing a per-sta work item from the tx free path can become very expensive
under load. This work is only supposed to pull rate control stats every
second and deal with rate control changes.
Additionally, the rate control update code was wrong, because it was
confusing bit masks and bit numbers in test_bit.
Fix this by introducing a dedicated device work item for rate control
updates, and by polling station stats from the phy mac work.
Stations requiring polling or rate control updates are added to lists
protected by dev->sta_poll_lock.
Signed-off-by: Felix Fietkau <[email protected]>
All drivers use this in pretty much the same way. Moving it to core helps with
some checks for the upcoming testmode support
Signed-off-by: Felix Fietkau <[email protected]>
Clean up the flow of per-rate txpower limit setting to get rid of
dulplicate work since it has already been handled by firmware, and set
proper max_power based on different channels and regdomains.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is easy to add MU EDCA parameters in the future. This patch
also fixes a wrong cw_min assignment.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In MT7915, hardware queue map is flexible. However, certain firmware modules
like MU and U-APSD presume a fixed queue order to adapt some devices that have
DMA scheduler with a strict order, so this patch can help in the long run.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Enable or disable OBSS PD when the bss config changes or we
assoc to an AP that broadcasts the IE.
With this patch, we can get ~20% gain in OBSS OTA environment.
Tested-by: Evelyn Tsai <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
make mac_work per phy instead of per device and fix a possible deadlock
in mt7915_stop since mt7915_mac_work runs holding mt76 mutex
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Enable TxBF modules and trigger sounding process to support Tx beamformer.
Signed-off-by: Ryder Lee <[email protected]>
Tested-by: Evelyn Tsai <[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
This allows host driver to get useful information of some important modules.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Chih-Min Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Driver can manually set fixed rate for each peer through debugfs.
May use .set_bitrate_mask callback and iterate stations under the
current vif to achieve the aim once it supports HE rate.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This generation supports much more per-peer statistics than legacy ones,
so add .sta_add_debugfs accordingly.
This is convenient to set/get more settings/counters in the long run.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The capabilities for the HE interfaces are generated from the capabilities
reported by the firmware.
This should move to common file once we got other HE devices support.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add support for the MediaTek latest generation IEEE 802.11ax 4x4
device MT7915E, which supports concurrent dual-band operation at
both 5GHz and 2.4GHz.
Note that this patch just add basic part and will add more HE
capabilities support in the further patches.
The driver supports AP, Station, Mesh and monitor mode.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Chih-Min Chen <[email protected]>
Suggested-by: Shihwei Lin <[email protected]>
Tested-by: Evelyn Tsai <[email protected]>
Acked-by: Yiwei Chung <[email protected]>
Acked-by: YF Luo <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Felix Fietkau