According to the firmware usage, OFDM rates should fill out bit 6 - 13
while CCK rates should fill out bit 0 - 3 in legacy field of RA info to
make the rate adaption runs propertly. Otherwise, a unicast frame might be
picking up the unsupported rate to send out.
Fixes: 1c099ab44727 ("mt76: mt7921: add MCU support")
Reported-by: Joshua Emele <[email protected]>
Co-developed-by: YN Chen <[email protected]>
Signed-off-by: YN Chen <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt7615_mcu_set_p2p_oppps routine in mt76_connac_lib module in order
to be reused in mt7921 driver
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Consider .max_reg_power in struct ieee80211_channel to limit the
maximum power the wireless device allowed to transmit on the
corresponding channel according to the regulatory domain.
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: YN Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Update the proper firmware programming sequence to fix GTK rekey
offload failure on WPA mixed mode.
In the mt76_connac_mcu_key_iter,
gtk_tlv->proto should be only set up on pairwise key
and gtk_tlk->group_cipher should be only set up on the group key.
Otherwise, those parameters required by firmware would be set
incorrectly to cause GTK rekey offload failure on WPA mixed mode
and then disconnection follows.
Fixes: b47e21e75c80 ("mt76: mt7615: add gtk rekey offload support")
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Leon Yen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
add .set_sar_specs to allow configuring SAR power limitations on the
frequency ranges from the userland.
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: YN Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Limit tx power for single-sku according to userlevel power.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When .sta_state is implemented, mac80211 assumes that the station entry is
usable after the NOTEXIST->NONE transition.
So we should create the sta entry as early as possible in order that
mac80211 pass assoc/auth frames to mt76 with the newly created sta entry,
and add .sta_assoc to mt76 core to refresh the sta entry again when sta is
being associated.
Fixes: 8aa5a9b7361c ("mt76: mt7921: enable deep sleep at runtime")
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Check device band capabilities before configuring single-sku
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt76_connac_mcu_get_nic_capability utility routine to poll
device capabilities returned by mcu fw for CE devices (mt7663/mt7921).
This is a preliminary patch to introduce 6GHz support.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Update MCU command usage to fix WoW configuration with disconnection
and bitmap pattern and to avoid magic number.
Fixes: ffa1bf97425 ("mt76: mt7921: introduce PM support")
Reviewed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: YN Chen <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Enable the deep sleep mode with that firmware is able to trap into
the doze state at runtime to reduce the power consumption further.
The deep sleep mode is not allowed in the STA state transition with
the firmware to have the fast connection experience as we've done in
the full power mode
Reviewed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
As already done for mt7615 and mt7915, enable rx header translation
offload for mt7921 in order to reduce cpu load in the rx path.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Introduce mt76_connac_mcu_set_deep_sleep to enable deep sleep mode
and will be activated immediately when the host returns the ownership
to the device.
Co-developed-by: Leon Yen <[email protected]>
Signed-off-by: Leon Yen <[email protected]>
Co-developed-by: YN Chen <[email protected]>
Signed-off-by: YN Chen <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76_connac_mcu_update_arp_filter in mt76_connac module since the
code is shared between mt7615 and mt7921
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Ensures that header translation is disabled for interfaces that do not support
it.
Fixes: bb1262e7199b ("mt76: mt7615: add support for rx decapsulation offload")
Signed-off-by: Felix Fietkau <[email protected]>
Reduce the data latency during hw_scan by the split scan which would switch
back to operational channel right after scanning each channel done.
Suggested-by: Asda Wen <[email protected]>
Suggested-by: Soul Huang <[email protected]>
Co-developed-by: YN Chen <[email protected]>
Signed-off-by: YN Chen <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
dwell time for the scan is not configurable according to the current
firmware submitted into linux-firmware.git, so leave the dwell time 0 to
indicate the dwell time always determined by the firmware.
Fixes: 399090ef9605 ("mt76: mt76_connac: move hw_scan and sched_scan routine in mt76_connac_mcu module")
Suggested-by: Soul Huang <[email protected]>
Co-developed-by: YN Chen <[email protected]>
Signed-off-by: YN Chen <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt76_sta_cmd_info data structure to contain parameters passed
to mt76_sta_cmd_info routine. This is preliminary patch to properly
configure rcpi for mt7921 devices.
Signed-off-by: Lorenzo Bianconi <[email protected]>
For AP and Client mode, the hardware can pass received packets
as 802.3 frames that can be passed to the network stack as-is.
Tested-by: Frank Wunderlich <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Update sched_scan command usage according to the current firmware
submitted into linux-firmware.git.
Fixes: 80fc1e37c0eb ("mt76: mt7921: rely on mt76_connac_mcu module for sched_scan and hw_scan")
Co-developed-by: Soul Huang <[email protected]>
Signed-off-by: Soul Huang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use proper value for ht40 mode configuration in mt76_connac_mcu_uni_add_bss
routine and not ht20 one
Fixes: d0e274af2f2e4 ("mt76: mt76_connac: create mcu library")
Co-developed-by: Soul Huang <[email protected]>
Signed-off-by: Soul Huang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Even if this is not a real bug since mt76_connac_mcu_alloc_wtbl_req routine
can fails just if nskb is NULL , always check return value from
mt76_connac_mcu_alloc_wtbl_req in order to avoid possible future
mistake.
Reported-by: Dan Carpenter <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce coredump support to mt7921 driver.
The coredump would be produced when MCU met the fatal error or driver
sent out the specific cmd to force trigger it.
Co-developed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rely on mt76_connac_mcu common library and remove duplicated code
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move WoW and suspend code in mt76_connac_mcu module in order to be reused in
mt7615 and mt7921 drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move hw_scan/sched_scan in mt76_connac_mcu module in order to be reused in
mt7615 and mt7921 drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt76_connac common mcu library for code sharing between mt7615 and
mt7921 devices
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
