Implement NAN_UNI_CMD_UPDATE_PHY_SETTING (tag=18) to configure the
BSS-level PHY parameters that the FW NAN scheduler uses when it
switches channels.
The command carries separate 2G and 5G PHY settings, each with its
own phy type, rate sets and protection modes.
Fixes: 0f3605e4f8de ("wifi: mt76: mt7925: wire up NAN operations")
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Stella Liu <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
mt7925_start_nan() called mt7925_nan_set_nmi_addr(), which makes NAN
start fail. The NMI address is not managed here, so drop the call.
Also track dev->nan_vif only in add/remove_interface and fold the
single BSS rollback into an inline error check.
Fixes: 0f3605e4f8de ("wifi: mt76: mt7925: wire up NAN operations")
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Stella Liu <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Per IEEE 802.11be, the Beamformee SS <= 80/160/320 MHz 3-bit subfields
in the EHT PHY Capabilities are encoded as (Nss - 1) and are required
to be >= 3 (i.e. at least 4 SS receive capability) whenever SU
Beamformee is advertised.
MT7925 is a 2x2 STA (sts = 2), so directly filling (sts - 1) = 1
violates the spec minimum. Clamp the encoded value to 3 when sts <= 3,
otherwise use (sts - 1). This is applied consistently to the
BEAMFORMEE_SS <= 80 MHz (split across phy_cap_info[0]/[1]), <= 160 MHz
and <= 320 MHz (6 GHz only) subfields.
Fixes: c948b5da6bbe ("wifi: mt76: mt7925: add Mediatek Wi-Fi7 driver for mt7925 chips")
Signed-off-by: shengwei.lu <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Fix the power table update sequence to ensure CLC is loaded before
setting SAR power table.
The firmware requires CLC baseline to be established first
to properly calculate the final power limit as min(clc_limit, rate_limit,sar_limit).
Fixes: 9557b6fe0c8b ("wifi: mt76: mt7925: refine the txpower initialization flow")
Signed-off-by: Jared.Huang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
mt7925 queues mlo_pm_work with a 5 second delay during multi-link
power-save setup and never cancels it on the stop path. If the device is
torn down inside that window, the work outlives the teardown and its timer
fires afterwards, trying to queue onto the workqueue that is already gone:
workqueue: cannot queue mt7925_mlo_pm_work [mt7925_common] on wq phy0
WARNING: kernel/workqueue.c:2283 at __queue_work+0x59/0xa0, CPU#1: swapper/1/0
call_timer_fn+0x2a/0x140
__run_timers+0x203/0x330
run_timer_softirq+0x86/0xf0
mt7921 already has its own stop callback, so add one for mt7925 that
cancels the work before calling mt792x_stop(). mt7925_ops backs both the
PCIe and USB drivers, so this covers both.
Fixes: 276a56883257 ("wifi: mt76: mt7925: update the power-saving flow")
Cc: [email protected]
Tested-by: Traockl <[email protected]>
Signed-off-by: Devin Wittmayer <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
If the device is reset, suspended or unregistered within that window,
the pending work can still run and access vif/bss data that may already
be freed, or send MCU commands while the firmware is not available.
Add cancel_delayed_work_sync(&dev->mlo_pm_work) in all relevant teardown
and suspend paths:
- mt7925_mac_reset_work() (chip reset recovery)
- mt7925e_unregister_device() (PCIe unbind)
- mt7925_pci_suspend() (PCIe bus suspend)
- mt7925_suspend() (mac80211 suspend)
- mt7925u_suspend() (USB bus / runtime suspend)
This ensures the work is stopped before the device state becomes
invalid.
Assisted-by: kimi-cli:kimi-k2.7 code
Assisted-by: atomcode:glm-5.2 #Reported-by
Fixes: 276a568832577 ("wifi: mt76: mt7925: update the power-saving flow")
Cc: [email protected]
Signed-off-by: Wentao Guan <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
A use-after-free issue occurs in mt76_rx_poll_complete due to a race
condition. The STA has already been removed, but the rx_status still
had a pointer to the wcid in the STA.
Set the links' wcid pointers to be NULL for a MLD in
mt7925_sta_pre_rcu_remove()
BUG: KASAN: invalid-access in mt76_rx_poll_complete+0x280/0x470
Call trace:
dump_backtrace+0xec/0x128
show_stack+0x18/0x28
dump_stack_lvl+0x40/0xc8
print_report+0x1b8/0x710
kasan_report+0xe0/0x144
do_bad_area+0x120/0x260
do_tag_check_fault+0x20/0x34
do_mem_abort+0x54/0xa8
el1_abort+0x3c/0x5c
el1h_64_sync_handler+0x40/0xcc
el1h_64_sync+0x7c/0x80
mt76_rx_poll_complete+0x280/0x470
mt76_dma_rx_poll+0x114/0x51c
mt792x_poll_rx+0x60/0xf8
napi_threaded_poll_loop+0xe0/0x450
napi_threaded_poll+0x80/0x9c
kthread+0x11c/0x158
ret_from_fork+0x10/0x20
Fixes: c948b5da6bbe ("wifi: mt76: mt7925: add Mediatek Wi-Fi7 driver for mt7925 chips")
Signed-off-by: Eason Lai <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
mt7925_sta_set_decap_offload() iterates over the vif valid_links mask
when updating decap offload state for an MLO station. The station may not
have a link STA for every valid link of the vif, so mt792x_sta_to_link()
can return NULL for a link that belongs to the vif but not to the station.
The function currently dereferences mlink before checking whether the
link WCID is ready. If mlink is NULL, setting or clearing
MT_WCID_FLAG_HDR_TRANS dereferences a NULL pointer.
Skip links without a station link before touching mlink->wcid.
Fixes: b859ad65309a ("wifi: mt76: mt7925: add link handling in mt7925_sta_set_decap_offload")
Signed-off-by: Guangshuo Li <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
In mt7925_mac_link_bss_add(), the MT7927 branch added an else-if that
checked mvif->phy->mt76->chandef.chan before assigning it to the local
chan pointer. If that check failed, chan stayed NULL and chan->band was
dereferenced unconditionally a line later.
phy->chandef.chan is set during phy registration in mt76_check_sband()
and is never cleared, so the check is a no-op. Drop it and use the
chandef channel as an unconditional fallback, matching the assumption
made elsewhere in the driver (e.g. the existing basic_rates_idx
selection right below this block and mt7925/mac.c).
Reported-by: kernel test robot <[email protected]>
Reported-by: Dan Carpenter <[email protected]>
Closes: https://lore.kernel.org/r/[email protected]/
Signed-off-by: Felix Fietkau <[email protected]>
With MLO, traffic for one TID can be sent on any active link. Programming
BA state only on the default link leaves the other active links out of
sync.
Program BA state on all active links instead.
Fixes: 766ea2cf5a39 ("Revert "wifi: mt76: mt7925: Update mt7925_mcu_uni_[tx,rx]_ba for MLO"")
Tested-by: Yao Ting Hsieh <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
MT7927 needs DBDC enabled and uses a fixed firmware band assignment for
2.4GHz and 5/6GHz BSS contexts.
Reprogram the STA dev context when the channel context is assigned so the
firmware sees the updated band_idx before the BSS is used. This avoids
stale band programming after band changes.
Co-developed-by: Javier Tia <[email protected]>
Signed-off-by: Javier Tia <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
mt7925_init_eht_caps() only populates EHT MCS/NSS maps for BW <= 80
and BW = 160, but never sets BW = 320. This means iw phy shows no
320MHz MCS map entries even though the hardware supports 320MHz
operation in the 6GHz band.
Add the missing 320MHz capability bits for 6GHz:
- PHY_CAP0: IEEE80211_EHT_PHY_CAP0_320MHZ_IN_6GHZ
- PHY_CAP1: beamformee SS for 320MHz
- PHY_CAP2: sounding dimensions for 320MHz
- PHY_CAP6: MCS15 support for 320MHz width
- MCS/NSS: populate bw._320 maps for 6GHz band
Introduce is_320mhz_supported() to gate 320MHz on MT7927 only, since
MT7925 does not support 320MHz operation.
Tested-by: Marcin FM <[email protected]>
Tested-by: Cristian-Florin Radoi <[email protected]>
Tested-by: George Salukvadze <[email protected]>
Tested-by: Evgeny Kapusta <[email protected]>
Tested-by: Samu Toljamo <[email protected]>
Tested-by: Ariel Rosenfeld <[email protected]>
Tested-by: Chapuis Dario <[email protected]>
Tested-by: Thibaut François <[email protected]>
Tested-by: 张旭涵 <[email protected]>
Reviewed-by: Sean Wang <[email protected]>
Signed-off-by: Javier Tia <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
In the error path of mt7925_change_vif_links(), the free: label iterates
over link_ids to clean up, but compares against `mconf` and `mlink`
which hold stale values from the last loop iteration rather than the
current link_id being freed.
Use array-indexed access (mconfs[link_id] / mlinks[link_id]) to compare
against the correct per-link pointers.
Fixes: 69acd6d910b0 ("wifi: mt76: mt7925: add mt7925_change_vif_links")
Tested-by: Marcin FM <[email protected]>
Tested-by: Cristian-Florin Radoi <[email protected]>
Tested-by: George Salukvadze <[email protected]>
Tested-by: Evgeny Kapusta <[email protected]>
Tested-by: Samu Toljamo <[email protected]>
Tested-by: Ariel Rosenfeld <[email protected]>
Tested-by: Chapuis Dario <[email protected]>
Tested-by: Thibaut François <[email protected]>
Tested-by: 张旭涵 <[email protected]>
Reviewed-by: Sean Wang <[email protected]>
Signed-off-by: Javier Tia <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
On a STATION vif, removing a TDLS peer takes the mt7925_mac_sta_remove
-> mt7925_mac_sta_remove_links path. The first loop in that function
calls mt7925_mcu_add_bss_info(..., enable=false) for every link of the
station being removed. For a non-MLO STATION vif there is exactly one
link, link 0, whose bss_conf is the AP's. TDLS peers do not have their
own bss_conf - they share the AP's BSS.
The result is that every TDLS peer teardown sends a BSS_INFO_UPDATE
with enable=0 for the AP's BSS to the firmware, which wipes the AP-side
rate-control context. The connection stays associated and TX from the
host still works at the negotiated rate, but the AP's downlink to us
collapses to the lowest mandatory OFDM rate (HE-MCS 0 / 6 Mbit/s OFDM)
and only slowly recovers as rate adaptation re-learns under sustained
traffic. With brief or bursty traffic the link can stay at 6-72 Mbit/s
indefinitely, requiring a manual reconnect.
mt7925_mac_link_sta_remove() already guards its own
mt7925_mcu_add_bss_info(..., false) call with
"vif->type == NL80211_IFTYPE_STATION && !link_sta->sta->tdls".
Add the equivalent guard at the top of the cleanup loop in
mt7925_mac_sta_remove_links(), above the link_sta / link_conf /
mlink / mconf lookups, so TDLS peer teardown skips the loop body
entirely without doing the per-link work that would just be thrown
away.
Verified on mt7925e by triggering Samsung-S938B auto-TDLS via iperf3
and watching iw rx bitrate after teardown:
Before: rx bitrate collapses to 6.0-72.0 Mbit/s, oscillates 17/72/
137/288/432 Mbit/s for 30+ seconds, no full recovery without
a manual reassoc.
After: rx bitrate stays at 1200.9 Mbit/s HE-MCS 11 NSS 2 80 MHz
across the entire TDLS lifecycle.
bpftrace confirms a single mt7925_mcu_add_bss_info(enable=0) call per
teardown before the fix; zero such calls after.
Fixes: 3878b4333602 ("wifi: mt76: mt7925: update mt7925_mac_link_sta_[add, assoc, remove] for MLO")
Cc: [email protected]
Signed-off-by: ElXreno <[email protected]>
Assisted-by: Claude:claude-opus-4-7 bpftrace
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
With HW TX encap offload enabled, the mt76 firmware builds the 802.11
header for the 802.3 frame using the per-WCID context. For a STATION
vif the HDR_TRANS TLV currently sets ToDS=1, which makes the firmware
default to the BSSID as A1 and emit STA->AP-formatted frames
regardless of which peer the WCID points to.
For TDLS-paired peers this is wrong. Data frames go on air addressed
to the AP, the AP MAC-ACKs and silently drops them per IEEE 802.11z
(an AP must not forward to a TDLS-paired peer). Management and
control frames bypass the HW encap path and still reach the peer;
only user data fails.
Add MT_WCID_FLAG_TDLS_PEER, set it in mt7915, mt7921, mt7925 and
mt7996 sta-add paths when sta->tdls is true, and override the
HDR_TRANS TLV in mt76_connac_mcu_wtbl_hdr_trans_tlv() (Connac2 -
mt7915 / mt7921 / mt7922), mt7925_mcu_sta_hdr_trans_tlv() (mt7925)
and mt7996_mcu_sta_hdr_trans_tlv() (mt7996) to set ToDS=0, FromDS=0
when the flag is set. The 3-addr non-DS form matches what 802.11z
uses for direct links; the firmware then constructs the frame with
A1=peer rather than A1=BSSID. HW encap offload remains enabled for
AP and any non-TDLS traffic.
Verified on mt7925e + Samsung S938B over a 5 GHz HE 80 MHz channel
with iperf3 -t 30 to the TDLS peer:
before fix: over the TDLS direct link, 7 TDLS Setup action
frames and 3 RTS frames reach the peer; 0 QoS
Data frames make it through (mgmt/control paths
bypass HW encap, the data path does not). iperf3
stalls.
after fix: 2.90 GBytes transferred at 830 Mbit/s sustained,
0 TCP retransmits.
mt7915, mt7921, mt7922 and mt7996 are not regression-tested in this
change for lack of hardware. Their HDR_TRANS handling mirrors the
verified mt7925 change; the firmware behavior is shared across these
chips.
Signed-off-by: ElXreno <[email protected]>
Assisted-by: Claude:claude-opus-4-7 bpftrace tcpdump
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
This patch is based on a BUG as reported by Bongani Hlope at
https://lore.kernel.org/all/[email protected]/
When a channel-switch announcement (CSA) beacon is received,
cfg80211 queues a wiphy work item that eventually calls
mt7921_channel_switch_rx_beacon(). If the station disconnects
(or the channel context is otherwise torn down) between the
time the work is queued and the time it runs, the driver's
dev->new_ctx pointer can already have been cleared to NULL.
mt7921_channel_switch_rx_beacon() then dereferences new_ctx
unconditionally, triggering a NULL pointer dereference at
address 0x0:
BUG: kernel NULL pointer dereference, address: 0000000000000000
RIP: 0010:mt7921_channel_switch_rx_beacon+0x1f/0x100 [mt7921_common]
The same missing guard exists in mt7925_channel_switch_rx_beacon(),
which shares the same code pattern introduced by the same commit.
Add an early-return NULL check for dev->new_ctx in both
mt7921_channel_switch_rx_beacon() and
mt7925_channel_switch_rx_beacon(). When new_ctx is NULL there is
no pending channel switch to process, so returning immediately is
the correct and safe action.
Fixes: 8aa2f59260eb ("wifi: mt76: mt7921: introduce CSA support")
Reported-by: Bongani Hlope <[email protected]>
Oops-Analysis: http://oops.fenrus.org/reports/lkml/[email protected]/report.html
Link: https://lore.kernel.org/all/[email protected]/
Signed-off-by: Arjan van de Ven <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: Felix Fietkau <[email protected]>
Cc: Lorenzo Bianconi <[email protected]>
Cc: Ryder Lee <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Release host link resources when mt7925_mac_sta_add_links() fails after
partial success.
msta->link[] and dev->mt76.wcid[] may already be published, so unwind
the host state to avoid leaving stale links behind.
Signed-off-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Move the msta->link[link_id] publication until after
mt7925_mac_link_sta_add() succeeds.
msta->link[] is RCU-visible, so publishing it before setup completes can
expose a link whose add path later fails. Publish it only after success
to avoid partially initialized link state becoming visible.
Signed-off-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Allocate mt792x_link_sta with kzalloc() and free it with kfree_rcu()
instead of devm-managed memory.
msta->link[] is published via RCU, so the link STA must remain valid
until readers have quiesced after teardown. Manage the object lifetime
with kfree_rcu() to match its RCU-visible publication.
Signed-off-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Move WCID teardown into mt7925_mac_link_sta_remove() to mirror the
dev->mt76.wcid[] publish done during link add.
This clears the published WCID before the rest of teardown, so WCID
lookups no longer expose a link that is being removed.
No functional change intended.
Signed-off-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Remove the redundant mt76_wcid_init() call after publishing the WCID in
mt7925_mac_link_sta_add().
WCID is already initialized before publication, so reinitializing it
afterward is unnecessary and makes the setup ordering less clear.
No functional change intended.
Signed-off-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Undo the published WCID state when mt7925_mac_link_sta_add() fails after
WCID setup.
The add path can fail after dev->mt76.wcid[] is published, so the error
path must clear the partial host-side WCID state to avoid leaving stale
entries behind.
No functional change intended.
Signed-off-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Drop the dead pri_link check in mt7925_mac_sta_remove_links() and
perform WCID cleanup unconditionally.
mlink->pri_link is already cleared before the test, making the branch
ineffective. This matches the actual teardown behaviour and simplifies
the remove path.
No functional change intended.
Signed-off-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Drop the mt792x_vif_to_link() lookup in mt7925_mcu_wtbl_update_hdr_trans()
and pass the resolved mconf and mlink from the caller instead. The link
context is already known at the call site, making the lookup redundant.
This keeps the helper lookup-free and makes link ownership explicit.
No functional change intended.
Signed-off-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
mt792x_sta_to_link() uses rcu_dereference_protected() and therefore
expects mt76.mutex to be held. Move the lookup after
mt792x_mutex_acquire() to make the locking explicit and correct.
Signed-off-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Drop the mt792x_sta_to_link() lookup in mt7925_set_link_key() and pass
the resolved mlink from the caller instead. The link context is already
known at the call site, making the lookup redundant.
This keeps the helper lookup-free and makes link ownership explicit.
No functional change intended.
Signed-off-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Drop the mt792x_sta_to_link() lookup in mt7925_mcu_wtbl_update_hdr_trans()
and pass the resolved mlink from the caller instead. The link context is
already known at the call site, making the lookup redundant.
This keeps the helper lookup-free and makes link ownership explicit.
No functional change intended.
Signed-off-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Drop the mt792x_sta_to_link() lookup in mt7925_mac_link_sta_remove()
and pass mlink from mt7925_mac_sta_remove_links() instead. The link is
already resolved there, making the extra lookup redundant.
This keeps the remove helper lookup-free and avoids hidden dependence on
msta->link[link_id] during teardown.
No functional change intended.
Signed-off-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Use mlink->wcid.def_wcid to obtain the primary mlink in
mt7925_mac_link_sta_add() instead of calling mt792x_sta_to_link().
The primary link context is already carried by the WCID, so the extra
lookup is redundant. This makes the add path follow the existing WCID
association directly.
No functional change intended.
Signed-off-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Drop the mt792x_sta_to_link() lookup in mt7925_mcu_sta_update() and
pass the resolved mlink from the caller instead. The link context is
already known at the call site, making the lookup redundant.
This keeps the helper lookup-free and makes WCID selection explicit.
No functional change intended.
Signed-off-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Drop the mt792x_sta_to_link() lookup in mt7925_mcu_bss_basic_tlv() and
pass the resolved WCID indices from the caller instead. The link
context is already known, so the lookup is redundant.
This makes link ownership explicit and keeps the helper lookup-free.
No functional change intended.
Signed-off-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
We are experiencing command timeouts because an upper layer triggers
an unexpected scan while the system/device is in suspend.
The upper layer should not initiate scans until the NIC has fully resumed.
We want to prevent scans during suspend and avoid timeouts without harming
power management or user experience.
Signed-off-by: Michael Lo <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
IEEE80211_CHANCTX_CHANGE_PUNCTURING is a channel context change
flag and should not be checked in the BSS change handler, where
the changed mask represents enum ieee80211_bss_change.
Remove the puncturing handling from the BSS path and rely on
mt7925_change_chanctx() to update puncturing configuration.
Fixes: cadebdad959b ("wifi: mt76: mt7925: add EHT preamble puncturing")
Signed-off-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
roc_abort_sync() can deadlock with roc_work(). roc_work() holds
dev->mt76.mutex, while cancel_work_sync() waits for roc_work()
to finish. If the caller already owns the same mutex, both
sides block and no progress is possible.
This deadlock can occur during station removal when
mt76_sta_state() -> mt76_sta_remove() ->
mt7925_mac_sta_remove_link() -> mt7925_mac_link_sta_remove() ->
mt7925_roc_abort_sync() invokes cancel_work_sync() while
roc_work() is still running and holding dev->mt76.mutex.
This avoids the mutex deadlock and preserves exactly-once
work ownership.
Fixes: 45064d19fd3a ("wifi: mt76: mt7925: fix a potential association failure upon resuming")
Co-developed-by: Quan Zhou <[email protected]>
Signed-off-by: Quan Zhou <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
timer_delete[_sync]() replaces del_timer[_sync](). Convert the whole tree
over and remove the historical wrapper inlines.
Conversion was done with coccinelle plus manual fixups where necessary.
Signed-off-by: Thomas Gleixner <[email protected]>
Signed-off-by: Ingo Molnar <[email protected]>
The selection of MLO mode should depend on the capabilities of the STA
rather than those of the peer AP to avoid compatibility issues with
certain APs, such as Xiaomi BE5000 WiFi7 router.
Fixes: 69acd6d910b0c ("wifi: mt76: mt7925: add mt7925_change_vif_links")
Signed-off-by: Leon Yen <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Currently, per-radio attributes are set on per-phy basis, i.e., all the
radios present in a wiphy will take attributes values sent from user. But
each radio in a wiphy can get different values from userspace based on
its requirement.
To extend support to set per-radio attributes, add support to get radio
index from userspace. Add an NL attribute - NL80211_ATTR_WIPHY_RADIO_INDEX,
to get user specified radio index for which attributes should be changed.
Pass this to individual drivers, so that the drivers can use this radio
index to change per-radio attributes when necessary. Currently, per-radio
attributes identified are:
NL80211_ATTR_WIPHY_TX_POWER_LEVEL
NL80211_ATTR_WIPHY_ANTENNA_TX
NL80211_ATTR_WIPHY_ANTENNA_RX
NL80211_ATTR_WIPHY_RETRY_SHORT
NL80211_ATTR_WIPHY_RETRY_LONG
NL80211_ATTR_WIPHY_FRAG_THRESHOLD
NL80211_ATTR_WIPHY_RTS_THRESHOLD
NL80211_ATTR_WIPHY_COVERAGE_CLASS
NL80211_ATTR_TXQ_LIMIT
NL80211_ATTR_TXQ_MEMORY_LIMIT
NL80211_ATTR_TXQ_QUANTUM
By default, the radio index is set to -1. This means the attribute should
be treated as a global configuration. If the user has not specified any
index, then the radio index passed to individual drivers would be -1. This
would indicate that the attribute applies to all radios in that wiphy.
Signed-off-by: Roopni Devanathan <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Johannes Berg <[email protected]>
The implementation amounts to setting the driver flag
IEEE80211_VIF_SUPPORTS_CQM_RSSI, and then providing
mechanisms for continuously updating enough information
to be able to provide notifications to userspace when
RSSI drops below a certain threshold
Signed-off-by: Jack Kao <[email protected]>
Signed-off-by: Ming Yen Hsieh <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
MediaTek has asked to switch from the ISC license to BSD-3-Clause-Clear,
in order to improve clarity and the legal integrity of the code.
The BSD-3-Clause license includes the "no endorsement" clause, which is
important for protecting the reputation of the original authors and
contributors by preventing unauthorized use of their names for endorsement
purposes.
This clause is absent in the BSD-2-Clause license, which is more permissive
but lacks this specific protection.
This change also cleans up the license of some Kconfig/Makefile files,
which were accidentally marked as GPL.
The GPL 2.0 remains in use on mt76x0, as well as two source files in mt7615
for which the license situation still needs to be clarified.
Signed-off-by: Felix Fietkau <[email protected]>
