Replace dbdc_support and tbtc_support with mt7996_band_valid() to
support mt7996 variants with band0/band2 dual-band support.
This changes reduces ambiguity when checking supported bands on different
variants or new chipsets, as well as during the init configurations on
DMA TX/RX queues or irq masks.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The internal struct and union inside mt7996_mcu_all_sta_info_event is
marked as being aligned, which conflicts with it being unaligned
within that structure:
drivers/net/wireless/mediatek/mt76/mt7996/mcu.h:165:2: error: field within 'struct mt7996_mcu_all_sta_info_event' is less aligned than 'union mt7996_mcu_all_sta_info_event::(anonymous at ../drivers/net/wireless/mediatek/mt76/mt7996/mcu.h:165:2)' and is usually due to 'struct mt7996_mcu_all_sta_info_event' being packed, which can lead to unaligned accesses [-Werror,-Wunaligned-access]
Mark all three as being packed as well to ensure byte packing for
the entire thing.
Fixes: adde3eed4a75 ("wifi: mt76: mt7996: Add mcu commands for getting sta tx statistic")
Signed-off-by: Arnd Bergmann <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Implement beacon protection feature for mt7996 chipsets, and also do
some cleanup on the set key routine.
Co-developed-by: Rudra Shahi <[email protected]>
Signed-off-by: Rudra Shahi <[email protected]>
Signed-off-by: Allen Ye <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add sta_rec_ht_uni struct to pass HT ampdu params to firmware. For VHT,
HE, and EHT mode, firmware will get the ampdu params by parsing the
corresponding capability.
Co-developed-by: Shayne Chen <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
During runtime, the GI value in the WTBL is not updated in real-time. To
obtain the latest results for the TX GI, switch to use an MCU command.
Signed-off-by: Benjamin Lin <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use per-phy structure for maximum txpower value initializing, since each
phy may have a different chainmask, which can impact the calculation of
power gain.
Co-developed-by: Allen Ye <[email protected]>
Signed-off-by: Allen Ye <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
For UBPR and FILS frames, the BSS_CHANGED_BEACON flag will also be set,
which causes those frames to use the beacon rate in TX descriptors.
Adjust the statement to fix this issue.
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: MeiChia Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use the new fixed rate command format to let the fixed field function
work normally.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Make mt7996_mcu_set_fixed_field() non-static in order to handle
IEEE80211_RC_SMPS_CHANGED in mt7996_mac_sta_rc_work().
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Always set the fixed_bw bitfield for fixed rate frames to keep it being
sent with specific bandwidth. Without this change, the bw of fixed rate
frames will still be decided by hardware.
Reported-by: Chank Chen <[email protected]>
Signed-off-by: Howard Hsu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Refactor and update dma prefetch parts and also split band 1 traffic to
PCIe 1 to enhance throughput.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
For connac3 chipsets, setting of spe_idx is moved from TX descriptor to
the fixed rate table. This patch implements the setting to support
duplicate TX mode for beacon.
Signed-off-by: StanleyYP Wang <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This patch adds support for thermal sensor device, including the
following features:
- Support to read current chip temperature.
- Support to set/get the trigger/restore temperature for thermal service.
- Support to read current chip tx cycle.
Signed-off-by: Howard Hsu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Implement thermal protection commands and support Linux cooling device
control for mt7996 chipsets.
Signed-off-by: Howard Hsu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add support to correctly configure the rx chainmask of variants that
have additional auxiliary RX path. e.g., 4T5R.
The auxiliary RX path is transparent to driver, but driver needs to
correctly configure it in the set channel fw command.
Co-developed-by: StanleyYP Wang <[email protected]>
Signed-off-by: StanleyYP Wang <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce the capability to reset mt7996 chipset if requested by wed
driver.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Similar to MT7915, enable Wireless Ethernet Ditpatcher for MT7996
to offload traffic received from the WLAN nic and transmitted on the
LAN one
Co-developed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Co-developed-by: Sujuan Chen <[email protected]>
Signed-off-by: Sujuan Chen <[email protected]>
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to introduce WED rx support for mt7996
driver.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Similar to MT7915, enable Wireless Ethernet Ditpatcher for MT7996
to offload traffic received from the LAN nic and transmitted on the
WLAN one
Co-developed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sujuan Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mtk_wed_device pointer in mt76_queue structure in order to
configure WED chip.
Get rid of dev parameter in Q_READ and Q_WRITE macros.
Introduce wed parameter to the following routine signatures:
- mt76_init_queue
- mt76_init_tx_queue
This is a preliminary patch to introduce WED support for mt7996 since
mt7996 runs two separate WED chips.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix the uninitialized variable warning in mt7996_mac_tx_free.
Fixes: 2461599f835e: "wifi: mt76: mt7996: get tx_retries and tx_failed from txfree"
Signed-off-by: Yi-Chia Hsieh <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove periodic MPDU TXS request. Get TID and FrameType from SKB
instead of TXWI, which is empty for Data Frame after MPDU TXS request
is removed, hence prohibiting the establishment of TX BA session.
Signed-off-by: Benjamin Lin <[email protected]>
Signed-off-by: Yi-Chia Hsieh <[email protected]>
Signed-off-by: Money Wang <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Evelyn Tsai <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Enable PPDU TxS by default. This makes the driver able to get Tx rate
information from TxS. The driver will also refresh BA session timer
on receive of PPDU TxS when WED is on.
Signed-off-by: Yi-Chia Hsieh <[email protected]>
Signed-off-by: Money Wang <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Evelyn Tsai <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Per peer Tx/Rx statistic can only be obtained by querying WM when WED is
on. This patch switches to periodic event reporting in the case of WED
being enabled.
Signed-off-by: Yi-Chia Hsieh <[email protected]>
Signed-off-by: Money Wang <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Evelyn Tsai <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Do not report cca and csa finish to upper layer on station type vif to
prevent warnings caused by setting beacon.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use the correct ieee80211_conf of each band for IEEE80211_CONF_MONITOR
comparison.
Fixes: 24e69f6bc3ca ("mt76: fix monitor rx FCS error in DFS channel")
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When the set_chan_info command is set with CH_SWITCH_NORMAL reason,
even if the action is UNI_CHANNEL_RX_PATH, it'll still generate some
unexpected tones, which might confuse DFS CAC tests that there are some
tone leakages. To get rid of these kinds of false alarms, always bypass
DPD calibration when IEEE80211_CONF_IDLE is set.
Reviewed-by: Evelyn Tsai <[email protected]>
Signed-off-by: StanleyYP Wang <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add CAP3_RX_CTRL_FRAME_TO_MULTIBSS check when setting sta_muru_tlv,
which is used to get stations's capability of receiving control frames
when running OFDMA with MBSSIDs.
Signed-off-by: Allen Ye <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When compiling with clang 16.0.6 and CONFIG_FORTIFY_SOURCE=y, I've
noticed the following (somewhat confusing due to absence of an actual
source code location):
In file included from drivers/net/wireless/mediatek/mt76/mt792x_core.c:4:
In file included from ./include/linux/module.h:13:
In file included from ./include/linux/stat.h:19:
In file included from ./include/linux/time.h:60:
In file included from ./include/linux/time32.h:13:
In file included from ./include/linux/timex.h:67:
In file included from ./arch/x86/include/asm/timex.h:5:
In file included from ./arch/x86/include/asm/processor.h:23:
In file included from ./arch/x86/include/asm/msr.h:11:
In file included from ./arch/x86/include/asm/cpumask.h:5:
In file included from ./include/linux/cpumask.h:12:
In file included from ./include/linux/bitmap.h:11:
In file included from ./include/linux/string.h:254:
./include/linux/fortify-string.h:592:4: warning: call to '__read_overflow2_field'
declared with 'warning' attribute: detected read beyond size of field (2nd
parameter); maybe use struct_group()? [-Wattribute-warning]
__read_overflow2_field(q_size_field, size);
In file included from drivers/net/wireless/mediatek/mt76/mt7915/main.c:4:
In file included from ./include/linux/etherdevice.h:20:
In file included from ./include/linux/if_ether.h:19:
In file included from ./include/linux/skbuff.h:15:
In file included from ./include/linux/time.h:60:
In file included from ./include/linux/time32.h:13:
In file included from ./include/linux/timex.h:67:
In file included from ./arch/x86/include/asm/timex.h:5:
In file included from ./arch/x86/include/asm/processor.h:23:
In file included from ./arch/x86/include/asm/msr.h:11:
In file included from ./arch/x86/include/asm/cpumask.h:5:
In file included from ./include/linux/cpumask.h:12:
In file included from ./include/linux/bitmap.h:11:
In file included from ./include/linux/string.h:254:
./include/linux/fortify-string.h:592:4: warning: call to '__read_overflow2_field'
declared with 'warning' attribute: detected read beyond size of field (2nd
parameter); maybe use struct_group()? [-Wattribute-warning]
__read_overflow2_field(q_size_field, size);
In file included from drivers/net/wireless/mediatek/mt76/mt7996/main.c:6:
In file included from drivers/net/wireless/mediatek/mt76/mt7996/mt7996.h:9:
In file included from ./include/linux/interrupt.h:8:
In file included from ./include/linux/cpumask.h:12:
In file included from ./include/linux/bitmap.h:11:
In file included from ./include/linux/string.h:254:
./include/linux/fortify-string.h:592:4: warning: call to '__read_overflow2_field'
declared with 'warning' attribute: detected read beyond size of field (2nd
parameter); maybe use struct_group()? [-Wattribute-warning]
__read_overflow2_field(q_size_field, size);
The compiler actually complains on 'mt7915_get_et_strings()',
'mt792x_get_et_strings()' and 'mt7996_get_et_strings()' due to the same
reason: fortification logic inteprets call to 'memcpy()' as an attempt
to copy the whole array from its first member and so issues an overread
warning. These warnings may be silenced by passing an address of the whole
array and not the first member to 'memcpy()'.
Signed-off-by: Dmitry Antipov <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Extend settings of LED registers to support per-band configuration.
Signed-off-by: Jen-Hao Cheng <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add support to configure parameters at runtime, such as mcs, gi, and
he_ltf. Note that EHT mode does not support this feature yet.
Co-developed-by: MeiChia Chiu <[email protected]>
Signed-off-by: MeiChia Chiu <[email protected]>
Signed-off-by: Howard Hsu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Only send commands that disable vif when removing interface, this
reduces some unnecessary bss_info and sta_rec commands, especially for
station interface.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
RX vector reports channel bandwidth 320-1 and 320-2 with different
values. Fix it to correctly report rx rate when using CBW320-2.
Fixes: 80f5a31d2856 ("wifi: mt76: mt7996: add support for EHT rate report")
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
According to P802.11be_D3.2 Table 9-404m, the minimum value of
Beamformee SS field shall be 3. Fix the values to follow the spec.
Fixes: 348533eb968d ("wifi: mt76: mt7996: add EHT capability init")
Signed-off-by: Howard Hsu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The bf_num field represents how many bands can support beamform, so set
the value to 3, and bf_bitmap represents the bitmap of bf_num.
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Howard Hsu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Set correct wcid in txp to let the SDO hw module look into the correct
wtbl, otherwise the tx descriptor may be wrongly fiiled. This patch also
fixed the issue that driver could not correctly report sta statistics,
especially in WDS mode, which misled AQL.
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Co-developed-by: Michael-CY Lee <[email protected]>
Signed-off-by: Michael-CY Lee <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The error handling code was added in order to allow tx enqueue to fail after
calling .tx_prepare_skb. Since this can no longer happen, the error handling
code is unused.
Signed-off-by: Felix Fietkau <[email protected]>
