Since we don't clean that tx queue from the tx tasklet, we need to do it
after the firmware upload is done. This patch also adds a cleanup step during
the upload, to help reclaim memory faster.
Fixes unprocessed queued frames eating up memory long after the firmware
upload has already completed
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt7615_mcu_rdd_send_pattern routine to trigger a radar pattern
detection. Moreover move debugfs related routines in a dedicated source
file.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add Channel Switch Announcement support to mt7615 driver updating beacon
template with CSA IE received from mac80211
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Delay channel calibration after Channel Availability Check. Add some
code cleanup to mt7615_mcu_set_channel
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add hw radar detection support to mt7615 driver in order to
unlock dfs channels on 5GHz band
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt7615_regd_notifier callback. This is a preliminary patch to
add radar detection support to mt7615 driver
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Simplify mt7615_set_channel signature removing cfg80211_chan_def
parameter since it is not actually used
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This makes sure that the driver update peer's bssid when state
transition occurs.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix wrong settings that will drop packets due to hardware's RX table
searching flow.
Fixes: f072c7ba21 ("mt76: mt7615: enable support for mesh")
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When TSSI calibration is disabled (which it means the device has been
equipped with an external power amplifier) we need to refer to
different eeprom fields in order to properly configure tx power
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Set per-channel target power as the minimum between the regulatory
tx power and the value configured in the eeprom
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move conn_type configuration directly in mt7615_mcu_set_sta_rec and
remove sta_rec_convert_vif_type since it is actually used just in
mt7615_mcu_set_sta_rec
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Do not check key pointer in mt7615_mcu_set_wtbl_key since if set_key_cmd
is SET_KEY, key will be always not NULL. This patch will address a false
positive reported by Coverity-Scan
Addresses-Coverity-ID: 1445463 ("Dereference after null check")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove tim_len in mt7615_mcu_set_bcn since it is not actually used
and ieee80211_beacon_get_tim checks if tim_length is NULL
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix wrong WCID assignment and add RKV (RX Key of this entry is valid)
flag to check if peer uses the same configuration with previous
handshaking.
If the configuration is mismatch, WTBL indicates a “cipher mismatch”
to stop SEC decryption to prevent the packet from damage.
Suggested-by: YF Luo <[email protected]>
Suggested-by: Yiwei Chung <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fixes gcc '-Wunused-but-set-variable' warnings:
drivers/net/wireless/mediatek/mt76/mt7603/mac.c: In function mt7603_fill_txs:
drivers/net/wireless/mediatek/mt76/mt7603/mac.c:969:5: warning: variable pid set but not used [-Wunused-but-set-variable]
drivers/net/wireless/mediatek/mt76/mt7603/mac.c:961:7: warning: variable final_mpdu set but not used [-Wunused-but-set-variable]
drivers/net/wireless/mediatek/mt76/mt7615/mac.c: In function mt7615_fill_txs:
drivers/net/wireless/mediatek/mt76/mt7615/mac.c:555:5: warning: variable pid set but not used [-Wunused-but-set-variable]
drivers/net/wireless/mediatek/mt76/mt7615/mac.c:552:19: warning: variable final_mpdu set but not used [-Wunused-but-set-variable]
They are never used, so can be removed.
Signed-off-by: YueHaibing <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt7603_get_rate in mac80211.c and rename it to mt76_get_rate
since it is shared between mt7603 and mt7615 drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Since all the routines in mt7615_config grub mt76.mutex moves
mutex_lock/mutex_unlock at the beginning/end of mt7615_config
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Initialize get_txpower mac80211 callback to mt76_get_txpower
in order to report the configured tx power to mac80211
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt7615_mcu_set_tx_power routine in order to cap tx power
according to the value configured by the user
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Select supported band according to the value read from
eeprom mtd/otp partition
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Calibration data are often available on a specific mtd partition on
embedded devices. Take into account eeprom calibration data if
available.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt7615_insert_ccmp_hdr in mac80211.c and rename it in
mt76_insert_ccmp_hdr since it is shared between mt7603 and mt7615
drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Stop mcu engine and then dma one in mt7615_unregister_device
in order to avoid a mcu hang in mt7615_unregister_device
Signed-off-by: Lorenzo Bianconi <[email protected]>
Make mt7615_rx_poll_complete static since it is used just in pci.c
to initialize rx_poll_complete function pointer
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Run __mt76_mcu_send_msg instead of __mt7615_mcu_msg_send and remove
duplicated code.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use common function wrapper in mt7615_mcu_exit since the code is shared
with m7603 driver
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use __mt76_mcu_send_msg wrapper instead of mt7615_mcu_msg_send.
This is a preliminary patch for mt7615-mt7603 mcu code unification
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use mt76 common signature for mt7615_mcu_msg_send. Move skb allocation
in mt7615_mcu_msg_send and remove duplicated code. Remove
__mt7615_mcu_set_wtbl and __mt7615_mcu_set_sta_rec since now are used
just to send mcu msgs. This is a preliminary patch for mt7615-mt7603 mcu
code unification
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove function pointers in mt7615_mcu_set_bss_info and run function
directly. Moreover remove __mt7615_mcu_set_bss_info since it is run just
by mt7615_mcu_set_bss_info and remove duplicated istructions
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Unify mt7615_mcu_set_dev_info and __mt7615_mcu_set_dev_info since the
latter is run just by mt7615_mcu_set_dev_info
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove skb_ret parameter from mt7615_mcu_msg_send signature since it is
actually used just by mt7615_mcu_patch_sem_ctrl. This is a prelimanry
patch to use mt76 common mcu API
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove dest parameter from mt7615_mcu_msg_send/__mt7615_mcu_msg_send
routine signature since it can is always set to MCU_S2D_H2N
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove query parameter from mt7615_mcu_msg_send routine signature since
it can be obtained from cmd value
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use proper mcu message size in mt7615_mcu_add_wtbl and do not
allocate a huge buffer. Moreover use stack memory instead of heap one
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use proper mcu message size in mt7615_mcu_add_wtbl_bmc and do not
allocate a huge buffer. Moreover use stack memory instead of heap one
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove bss_info_convert_vif_type routine since it is run just in
mt7615_mcu_set_bss_info and the switch over vif->type is already there.
Simplify mt7615_mcu_set_bss_info routine
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Do not loop over cmd payload in __mt7615_mcu_set_sta_rec since it is
already done in before running __mt7615_mcu_set_sta_rec (e.g.
mt7615_mcu_set_sta_rec)
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Do not loop over cmd payload in __mt7615_mcu_set_wtbl since it is
already done in before running __mt7615_mcu_set_wtbl (e.g.
mt7615_mcu_set_wtbl_key)
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix sparse warning:
drivers/net/wireless/mediatek/mt76/mt7615/pci.c:37:13:
warning: symbol 'mt7615_irq_handler' was not declared. Should it be static?
Signed-off-by: YueHaibing <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
