- initialize and use per-sta wcid entry instead of vif wcid
- set wcid flags for 4addr/offload
- fix 'newly' argument for vif sta entry update
Signed-off-by: Felix Fietkau <[email protected]>
On MT7915, MCU hangs do not trigger watchdog interrupts, so they can only
be detected through MCU message timeouts. Ensure that the hardware gets
restarted when that happens in order to prevent a permanent stuck state.
Signed-off-by: Felix Fietkau <[email protected]>
In some cases MCU messages can get lost. Instead of failing completely,
attempt to recover by re-sending them.
Signed-off-by: Felix Fietkau <[email protected]>
This allows the core code to change the channel. Code deduplication and
preparation for adding scanning code to the core.
Signed-off-by: Felix Fietkau <[email protected]>
Currently, CONNAC2 series do not support encryption for fragmented Tx frames.
Therefore, add dummy function mt7915_set_frag_threshold() to prevent SW
IEEE 802.11 fragmentation.
Signed-off-by: Benjamin Lin <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
of_gpio.h is deprecated and subject to remove.
The driver doesn't use it, simply remove the unused header.
Signed-off-by: Andy Shevchenko <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix the following sparse warnings:
drivers/net/wireless/mediatek/mt76/mt7915/debugfs.c:1133:29: error: too long token expansion
drivers/net/wireless/mediatek/mt76/mt7915/debugfs.c:1133:29: error: too long token expansion
drivers/net/wireless/mediatek/mt76/mt7915/debugfs.c:1133:29: error: too long token expansion
drivers/net/wireless/mediatek/mt76/mt7915/debugfs.c:1133:29: error: too long token expansion
No functional changes, compile tested only.
Fixes: e3296759f347 ("wifi: mt76: mt7915: enable per bandwidth power limit support")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Acked-by: Felix Fietkau <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Link: https://msgid.link/5457b92e41909dd75ab3db7a0e9ec372b917a386.1710858172.git.lorenzo@kernel.org
When pre-calibration data is missing, do not fail the driver probe.
Instead, just print a warning and fall back to regular calibration.
Signed-off-by: Felix Fietkau <[email protected]>
Add pre-calibration for mt7986 and mt7916. It has different data size
with mt7915. Group cal needs 54k and 94k for 2G + 5G and 2G + 6G,
respectively. DPD cal needs 300k.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: StanleyYP Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Send an update to the MCU whenever the settings change
Signed-off-by: MeiChia Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Set correct beamformer capabilities for station vif in HE PHY
capabilities IE.
Signed-off-by: Howard Hsu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Do not report measurements if the airtime counter was cleared since the
last update (possibly by firmware)
Signed-off-by: Henry Yen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The mcu command format are different for mt7915 and mt7986.
Fix the mt7915_mcu_wed_wa_tx_stats to support mt7915 and mt7986.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce wed.c in order to collect mt76 wed common codebase used by
mt7915 and mt7996 drivers.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Sicne the mapping is global, mapped register access needs to be protected
against concurrent access, otherwise a race condition might cause the reads
or writes to go towards the wrong register
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Do not clear the interrupt mask register on MT7915, since that prevents
MCU_CMD interrupts from being reported, thus causing timeouts during the
reset sequence. Defer stopping WED until tx/rx processing activity has
stopped.
Signed-off-by: Felix Fietkau <[email protected]>
Just like MT7916 also MT7981 can handle 3T3R DBDC frontend and should
hence be included in the corresponding conditional expression in the
driver. Add it.
Fixes: 6bad146d162e ("wifi: mt76: mt7915: add support for MT7981")
Signed-off-by: StanleyYP Wang <[email protected]>
Signed-off-by: Daniel Golle <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The offset of the TSSI flag on the EEPROM of MT7981 devices was wrong.
Set the correct offset instead.
Fixes: 6bad146d162e ("wifi: mt76: mt7915: add support for MT7981")
Signed-off-by: StanleyYP Wang <[email protected]>
Signed-off-by: Daniel Golle <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The power gain value is related to total TX path, so change the
calculation to use per-phy chainmask.
Signed-off-by: Allen Ye <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use per-phy structure for maximum txpower value initializing, since each
phy may have a different chainmask, which can impact the calculation of
power gain.
Co-developed-by: Allen Ye <[email protected]>
Signed-off-by: Allen Ye <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt76 assumes mt7915_mmio_wed_init can fail just after wed driver has
been attached running mtk_wed_device_attach().
Fall back to non-wed mode if platform_get_resource fails in
mt7915_mmio_wed_init routines.
Fixes: eebb70976be5 ("wifi: mt76: mt7915: enable wed for mt7986-wmac chipset")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move WED reset code shared between mt7915 and mt7996 in common module.
This is a preliminary patch to introduce WED reset support for mt7996.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mtk_wed_device pointer in mt76_queue structure in order to
configure WED chip.
Get rid of dev parameter in Q_READ and Q_WRITE macros.
Introduce wed parameter to the following routine signatures:
- mt76_init_queue
- mt76_init_tx_queue
This is a preliminary patch to introduce WED support for mt7996 since
mt7996 runs two separate WED chips.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to introduce WED support for mt7996
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to introduce WED support for mt7996
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt76_mmio_wed_offload_enable and mt76_mmio_wed_offload_disable routines
will be reused by mt7996 driver for wed support.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76_mmio_wed_init_rx_buf and mt76_mmio_wed_release_rx_buf routines
in common code.
This is a preliminary patch to introduce WED support for mt7996
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Felix Fietkau