After initially establishing a connection, it can produce multi-second latency
spikes and tx hangs when pushing traffic.
It should work better for MT7916 and MT7986, so leave it enabled there
Signed-off-by: Felix Fietkau <[email protected]>
According IEEE Std 802.11-2020, its definition is:
Indicates whether the STA is capable of interpreting the Extended NSS BW
Support subfield of the VHT Capabilities Information field.
Some APs, such as Xiaomi AX6000, would check this one for BW settings.
mt76 driver can get max BW capability only if the this field is confgured
properly.
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Ming Yen Hsieh <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This patch disables RX_TRANS_SHORT to make MDP to do header translation
when payload less than 8 bytes, hence the (QoS) null data can be encapsulated
to 802.3 format. However, WDS requires (QoS) null data in 802.11 format
to created vlan AP interfaces.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: lian.chen <[email protected]>
Signed-off-by: Sujuan Chen <[email protected]>
Signed-off-by: Bo Jiao <[email protected]>
Don't populate the read-only array ppet16_ppet8_ru3_ru0 on the stack but
instead make it static const. Also makes the object code a little smaller.
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
Signed-off-by: Colin Ian King <[email protected]>
Soft reboot might not clear certain condition, so always call
mt7915_wfsys_reset() during init.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Clean up and fix error paths in mt7915_register_device
Initialize second DBDC tx queue in mt7915_dma_init
Signed-off-by: Felix Fietkau <[email protected]>
Various spelling mistakes in comments.
Detected with the help of Coccinelle.
Signed-off-by: Julia Lawall <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This patch fixes performance issue of beamforming tx on
bandwidth 160MHz.
Fixes: 99ad32a4ca3a ("mt76: mt7915: add support for MT7986")
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
By default, mt7915e does not enable thermal management until the default
thermal zone does not reach a trip point. If the rest of the system
have better cooling than the wireless hardware, then it is possible that
the wireless chip can overheat while the rest of the system is fine.
Signed-off-by: Nicolas Cavallari <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The firmware-controlled actual throttle state was previously available
by reading the cooling_device, but this confused the thermal subsystem.
Add a hwmon attribute to get it instead.
Signed-off-by: Nicolas Cavallari <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt7915e registers a cooling_device with wrong semantics:
1. cooling_device expect that higher states values should cool more, but
mt7915e did the opposite... with the exception of state == 0, which
should "disable thermal management", but does not seem to have any
effect since the previous state is kept.
The result is that when the thermal zone heats up a bit and bumps the
cooling_device state from 0 to 1 to cool a bit, the performance is
destroyed, and when going back from 1 to 0, the performance stays bad.
2. Reading the cooling_device state does not always return the last
written state, but can return the actual hardware throttle state,
which is different.
This is a problem because the mt7915 firmware actually implement the
equivalent of a thermal zone with trip points. Setting the cooling
device state actually changes the throttles at each trip point, so the
following could occur if the first issue is fixed:
- thermal subsystem set state to 100% power (state=0)
- mt7915e driver set trip throttles to [100%, 50%, 25%, 12%]
- hardware heats up and decides to switch to 50% power
- thermal subsystem see that power is 50% (state=50), decide to increase
it to 60% (state=40) because the rest of the system is cool.
- mt7915e driver set trip throttle to [60%, 30%, 15%, 7%]
- hardware thus switches to 30% power
[race to the bottom continues...]
This patch corrects the semantics of the cooling_device to the one that
the thermal subsystem expect it.
Signed-off-by: Nicolas Cavallari <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
fix logic error and remove the unused member 'adie' of mt7915_dev.
Fixes: 91eeaef2523f ("mt76: mt7915: add support for MT7986")
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Client mode on DFS channels was broken, because the old code was activating
the DFS detector on radar channels while leaving it in CAC state.
This was caused by making the decision based on the channel radar flag,
instead of hw->conf.radar_enabled.
In order to properly deal with the various corner cases, rip out the state
handling code and replace it with something that's much easier to reason
about.
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt7915_mcu_rdd_background_enable and
mt7915_mcu_background_chain_ctrl routines to configure rx dfs dedicated chain.
This is a preliminary patch to add zero-wait dfs support performing CAC
detection on rdd2.
Tested-by: Owen Peng <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
fix code defect, variable 'val' is used without initialization
in mt7915_wfsys_reset().
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The RXQ of mt7916 are separated to MT_RXQ_MAIN_WA and MT_RXQ_MCU_WA,
so, add initialization and preftech setting for the queue MT_RXQ_MAIN_WA.
This is an intermediate patch to add mt7916 support.
Co-developed-by: Sujuan Chen <[email protected]>
Signed-off-by: Sujuan Chen <[email protected]>
Co-developed-by: Ryder Lee <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Update max rx len of some hw modules, which aligns out vendor SDK.
In normal modes, we exchange MPDU 7991 cap with peers; however, this
won't play a part in sniffer mode.
To prevent packets which exceed the max MPDU size from entering specific
rx path in hw, we need to set a proper limit to filter them out.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix missing HE phy cap related to vif and starec setting.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Enable HE UL MU-MIMO in sta_rec_muru, which works on both ap and station
mode.
For sending trigger frames, one of the conditions fw uses is to check if
mib rx airtime meets the threshold.
There's a main control of mib rx airtime report register in fw, so we
need to enable the register by mcu cmd instead of directly writing it,
otherwise it will still be disabled by fw.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce a dedicated mt76 debugfs sub-dir for ext-phy in dbdc mode.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce individual TWT support to mt7915 in AP mode.
Implement the two following mac80211 callbacks:
- add_twt_setup
- twt_teardown_request
Tested-by: Peter Chiu <[email protected]>
Tested-by: Evelyn Tsai <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Without this change, garbage is seen in the hwmon name and sensors output
for mt7915 is garbled. It appears that the hwmon logic does not make a
copy of the incoming string, but instead just copies a char* and expects
it to never go away.
Fixes: d6938251bb5b ("mt76: mt7915: add thermal sensor device support")
Signed-off-by: Ben Greear <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The user is allowed to change beacon tx rate (HT/VHT/HE) from hostapd.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Initialize brightness_set and blink_set callbacks to enable LED support.
The base 0x7c000000 is MCU space so driver can't touch it, and should
map the LED base to 0x18000000 host's view.
Signed-off-by: MeiChia Chiu <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Money Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mcu APIs to configure bss coloring and to report bss coloring
collisions. Add support to report coloring countdown in beacon sent by
the device.
Co-developed-by: Ryder Lee <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
At 160, this chip can only do 2x2 NSS. Fix the features
accordingly, verified it shows up properly in iw phy foo info
now.
Signed-off-by: Ben Greear <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
With this patch, users can set the trigger/restore temperature for
thermal service according to their use cases.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
