After flushing software-pending frames to DMA, mt76_has_tx_pending()
only checks DMA ring q->queued. For token-based drivers, q->queued is
decremented at DMA consumption, but firmware may not have transmitted
the frame yet. Waiting for all tokens is not feasible because data
frames may be stuck in firmware powersave/aggregation queues.
Track PSD queue tokens (firmware ALTX) per phy using an atomic counter.
These frames are sent by firmware immediately without PS buffering, so
the counter reliably reaches zero after transmission.
Increment the counter in mt76_token_consume() and decrement it in
mt76_token_release(), only for PSD queue tokens. Include the counter
in mt76_has_tx_pending() so channel switch waits for firmware TX
completion of management and nullfunc frames.
mt7615 (uses mt76_token_get/put) and non-token drivers are unaffected
as they never call mt76_token_consume/release.
Signed-off-by: Felix Fietkau <[email protected]>
Check frame length before accessing the mgmt fields in
mt76_connac2_mac_write_txwi_80211 in order to avoid a possible oob
access.
Fixes: 182071cdd594b ("mt76: connac: move connac2_mac_write_txwi in mt76_connac module")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Unify all per-chip conditionals under the new is_connac2() helper. This
avoids confusion caused by the previous is_mt7921() check, which
implicitly covered multiple connac2 chipsets and no longer reflected its
actual scope. This is a clean-up only change with no functional impact.
Signed-off-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Reset ampdu_state if ieee80211_start_tx_ba_session() fails in
mt76_connac2_tx_check_aggr(), otherwise the driver may incorrectly
assume aggregation is active and skip future BA setup attempts.
Fixes: 163f4d22c118 ("mt76: mt7921: add MAC support")
Signed-off-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Passing a BSS conf pointer to mt76_connac2_mac_tx_rate_val() currently has
two inconsistencies.
When called from mt76_connac2_mac_write_txwi(), BSS conf is got by
dereferencing a vif pointer. A NULL vif isn't accounted for though the
function itself supposes it to be NULL and tries to handle this case in
previous checks. This looks like a cosmetic change since the drivers
calling the function (namely, mt7915 and mt7921) set WANT_MONITOR_VIF flag
so judging by info->control.vif initialization inside ieee80211_tx_*()
routines it can't actually come as NULL here.
The same holds for the BSS conf pointer handling inside
mt76_connac2_mac_tx_rate_val(). It is dereferenced before being checked
for NULL. The function supposes to handle the case so reorder the check
and dereference of the pointer. Again, this looks like a syntax issue
only.
Found by Linux Verification Center (linuxtesting.org) with SVACE static
analysis tool.
Co-developed-by: Matvey Kovalev <[email protected]>
Signed-off-by: Matvey Kovalev <[email protected]>
Signed-off-by: Fedor Pchelkin <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
MediaTek has asked to switch from the ISC license to BSD-3-Clause-Clear,
in order to improve clarity and the legal integrity of the code.
The BSD-3-Clause license includes the "no endorsement" clause, which is
important for protecting the reputation of the original authors and
contributors by preventing unauthorized use of their names for endorsement
purposes.
This clause is absent in the BSD-2-Clause license, which is more permissive
but lacks this specific protection.
This change also cleans up the license of some Kconfig/Makefile files,
which were accidentally marked as GPL.
The GPL 2.0 remains in use on mt76x0, as well as two source files in mt7615
for which the license situation still needs to be clarified.
Signed-off-by: Felix Fietkau <[email protected]>
Several places use rcu_dereference to get a wcid entry without validating
if the index exceeds the array boundary. Fix this by using a helper function,
which handles validation.
Signed-off-by: Felix Fietkau <[email protected]>
Fixes linked list management issues during restart, where sta entries
can be recreated and reinitialized while still in the poll list, triggering
kernel warnings.
Signed-off-by: Felix Fietkau <[email protected]>
Rework connac helpers related to rate and phymode.
This is a preliminary patch to add MLO support for mt7996 chipsets.
Co-developed-by: Bo Jiao <[email protected]>
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add fragmentation index into TXD.DW2 to support IEEE 802.11 fragmentation.
Signed-off-by: Benjamin Lin <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The PPDU TxS does not include the error bit so it cannot use to report
status to mac80211.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When using fixed rate, HW uses txd DW9 to store tx arrivial time if VTA
is set. It would overwrite the msdu_id in txd and lead to token pending
if amsdu is enable.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mtk_wed_device pointer in mt76_queue structure in order to
configure WED chip.
Get rid of dev parameter in Q_READ and Q_WRITE macros.
Introduce wed parameter to the following routine signatures:
- mt76_init_queue
- mt76_init_tx_queue
This is a preliminary patch to introduce WED support for mt7996 since
mt7996 runs two separate WED chips.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The variable band should be determined by the ieee80211_chanctx_conf when
the driver is a kind of chanctx one e.g mt7921 and mt7922 driver so we
added the extension to mt76_connac2_mac_tx_rate_val by distinguishing if
it can support chanctx to fix the incorrect rate pickup.
Fixes: 41ac53c899bd ("wifi: mt76: mt7921: introduce chanctx support")
Signed-off-by: Sean Wang <[email protected]>
Reviewed-by: David Ruth <[email protected]>
Tested-by: David Ruth <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce is_mt7925() helper for new chipset. mt7925 runs the same
firmware download and mmio map flow as mt7921.
This is a preliminary patch to support mt7925 driver.
Co-developed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The error handling code was added in order to allow tx enqueue to fail after
calling .tx_prepare_skb. Since this can no longer happen, the error handling
code is unused.
Signed-off-by: Felix Fietkau <[email protected]>
Move the following routines in mt76-connac lib since they are shared
between mt7915 and mt7921:
- mt76_connac2_tx_check_aggr
- mt76_connac2_txwi_free
- mt76_connac2_tx_token_put
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
txs may be dropped if the frame is aggregated in AMSDU. When the problem
shows up, some SKBs would be hold in driver to cause network stopped
temporarily. Even if the problem can be recovered by txs timeout handling,
mt7921 still need to disable txs in AMSDU to avoid this issue.
Cc: [email protected]
Fixes: 163f4d22c118 ("mt76: mt7921: add MAC support")
Reviewed-by: Shayne Chen <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Concurrent binding/non-binding skbs could be handled anywhere which leads
to mixed byte counting, so switch to use PPDU TxS reporting regardless Tx
paths when WED is active.
Fixes: 43eaa3689507 ("wifi: mt76: add PPDU based TxS support for WED device")
Co-developed-by: Ryder Lee <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
PPDU TxS can only report MPDU count whereas mac80211 requires MSDU scale
(NL80211_STA_INFO_TX_PACKETS), so switch to get MSDU counts from WA
statistic.
Note that mt7915 WA firmware only counts tx_packet for WED path, so driver
needs to take care of host path additionally.
Fixes: 43eaa3689507 ("wifi: mt76: add PPDU based TxS support for WED device")
Co-developed-by: Ryder Lee <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Get missing tx retries/failed counts from txfree done events and report
them via mt7915_sta_statistics().
Co-developed-by: Peter Chiu <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
gen_ppe_thresh routine is shared between mt7615, mt7915, mt7921 and
mt7996 so move it in mt76_connac module.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Take nss calculation into account since this function always wrongly
returns 0.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The vif->bss_conf.mcast_rate should be applied to multicast data frame
only.
Fixes: 182071cdd594 ("mt76: connac: move connac2_mac_write_txwi in mt76_connac module")
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
There's no keep-alive packet being received by mac80211 stack when WED
is enabled, which leads to tx BA session timeout. This patch calls
ieee80211_refresh_tx_agg_session_timer() to refresh timer according
to tx status reporting.
Signed-off-by: Ryder Lee <[email protected]>
Rely on connac library for radiotap parsing and drop the following routines:
- mt7996_mac_decode_he_radiotap
- mt7996_mac_decode_he_mu_radiotap
- mt7996_mac_decode_he_radiotap_ru
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In order to fix a possible NULL pointer dereference in
mt7996_mac_write_txwi() of vif pointer, export
mt76_connac2_mac_tx_rate_val utility routine and reuse it
in mt7996 driver.
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The default case for frame_contorl is invalid. We should always
assign addr3 of this frame properly.
Coverity error message:
if (ieee80211_has_a4(hdr.frame_control))
(19) Event uninit_use_in_call: Using uninitialized value "hdr".
Field "hdr.addr3" is uninitialized when calling "memcpy".
memcpy(skb_push(skb, sizeof(hdr)), &hdr, sizeof(hdr));
else
memcpy(skb_push(skb, sizeof(hdr) - 6), &hdr, sizeof(hdr) - 6);
Fixes: 0880d40871d1 ("mt76: connac: move mt76_connac2_reverse_frag0_hdr_trans in mt76-connac module")
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The hardware reports the number of transmitting antennas not the actual
number of spatial streams
Co-developed-by: Peter Chiu <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Evelyn Tsai <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add mt76_connac_spe_idx() for antenna mask to spatial extension
index conversion. This is used to support flexible control of
tx antenna.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Given that there's no data coming from network stack for binding flows,
hence driver counts and reports station's statistics directly through
NL80211_STA_INFO_* based on active PPDU based TxS for offloading data.
Apart from that, WA firmware and its offloading engine (SDO) have hardcoded
"2" as PID, so we introduce MT_PACKET_ID_WED to differentiate WED reporting.
Note that PPDU format TxS is mutually exclusive with MT_TXD5_TX_STATUS_HOST.
Co-developed-by: Yi-Chia Hsieh <[email protected]>
Signed-off-by: Yi-Chia Hsieh <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Report phy_indx in tx_info->hw_queue. This is a preliminary patch to add
newer chipset support
Co-developed-by: Bo Jiao <[email protected]>
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Introduce phy_idx to mt76_wcid structure instead of ext_phy.
This is a preliminary patch to add newer chipset support.
Co-developed-by: Bo Jiao <[email protected]>
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Introduce phys array in mt76_dev structure to reference mt76_phy
supported by the chipset. This is a preliminary patch to introduce
newer chipset support.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Move mt76_connac_init_tx_queues and mt76_connac_tx_cleanup routines
in mt76_connac module. This is a preliminary patch to add mt7990
chipset support.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Previously the code used skb_set_queue_mapping for management or non-bufferable
powersave frames that need to be sent to a different hardware queue.
This can confuse AQL, which expects the value to remain the same until the tx
status report.
The only place that currently uses the altered skb queue mapping is the txwi
write function. Change the code to pass the hardware queue id as a function
parameter instead.
Signed-off-by: Felix Fietkau <[email protected]>
Move mt7615_txp_skb_unmap in shared code and reuse it in mt7915e and
mt7921e driver.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Now we can move mt76_connac_write_hw_txp routine in mt76-connac module
and reuse it in mt7921e and mt7615e driver.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Since now txp structures are in common code we can reuse
mt76_connac_tx_complete_skb routine in mt7921e, mt7915e and mt7615e
drivers.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rely on mt76_connac2_mac_fill_rx_rate routine in mt7921 driver.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt76_connac2_reverse_frag0_hdr_trans routine is shared between mt7921
and mt7915e drivers.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
HE radiotap parsing code is shared between connac2 devices.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
