Call mt7921_regd_update() instead of mt7921_mcu_set_clc() when setting
the 6GHz power type after connection, so that regulatory limits and SAR
power are also applied.
Fixes: 51ba0e3a15eb ("wifi: mt76: mt7921: add 6GHz power type support for clc")
Signed-off-by: Michael Lo <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Add MT7902 PCIe specific DMA layout overrides for MCU TXQ index, RX ring
size, and MCU_WA usage. Common layout remains the default for other chips.
This is a prerequisite patch before enabling MT7902 PCIe support.
Co-developed-by: Xiong Huang <[email protected]>
Signed-off-by: Xiong Huang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
MT7902 PCIe requires a different wm2_complete_mask value, so introduce a
mutable per-device copy of the default irq_map and override the field
only for this chip. Other devices continue using the shared const
template.
This is a prerequisite patch before enabling MT7902 PCIe support.
Co-developed-by: Xiong Huang <[email protected]>
Signed-off-by: Xiong Huang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Replace explicit napi_disable() calls for RX queues with
mt76_for_each_q_rx() in mt7921e_mac_reset().
This removes hardcoded queue indices and disables all configured
RX queues during reset.
Signed-off-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
roc_abort_sync() can deadlock with roc_work(). roc_work() holds
dev->mt76.mutex, while cancel_work_sync() waits for roc_work()
to finish. If the caller already owns the same mutex, both
sides block and no progress is possible.
This deadlock can occur during station removal when
mt76_sta_state() -> mt76_sta_remove() -> mt7921_mac_sta_remove() ->
mt7921_roc_abort_sync() invokes cancel_work_sync() while
roc_work() is still running and holding dev->mt76.mutex.
This avoids the mutex deadlock and preserves exactly-once
work ownership.
Fixes: 352d966126e6 ("wifi: mt76: mt7921: fix a potential association failure upon resuming")
Co-developed-by: Quan Zhou <[email protected]>
Signed-off-by: Quan Zhou <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
The mt7921_set_roc API may be executed concurrently with mt7921_roc_work,
specifically between the following code paths:
- The check and clear of MT76_STATE_ROC in mt7921_roc_work:
if (!test_and_clear_bit(MT76_STATE_ROC, &phy->mt76->state))
return;
- The execution of ieee80211_iterate_active_interfaces.
This race condition can interrupt the ROC abort flow, resulting in
the ROC process failing to abort as expected.
To address this defect, the modification of MT76_STATE_ROC is now
protected by mt792x_mutex_acquire(phy->dev). This ensures that
changes to the ROC state are properly synchronized, preventing
race conditions and ensuring the ROC abort flow is not interrupted.
Fixes: 034ae28b56f1 ("wifi: mt76: mt7921: introduce remain_on_channel support")
Cc: [email protected]
Signed-off-by: Quan Zhou <[email protected]>
Reviewed-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/2568ece8b557e5dda79391414c834ef3233049b6.1769133724.git.quan.zhou@mediatek.com
Signed-off-by: Felix Fietkau <[email protected]>
Set the MT76_STATE_MCU_RUNNING bit only after mt7921_load_clc()
has successfully completed. Previously, the MCU_RUNNING state
was set before loading CLC, which could cause conflict between
chip mcu_init retry and mac_reset flow, result in chip init fail
and chip abnormal status. By moving the state set after CLC load,
firmware initialization becomes robust and resolves init fail issue.
Signed-off-by: Quan Zhou <[email protected]>
Reviewed-by: [email protected]
Link: https://patch.msgid.link/19ec8e4465142e774f17801025accd0ae2214092.1763465933.git.quan.zhou@mediatek.com
Signed-off-by: Felix Fietkau <[email protected]>
timer_delete[_sync]() replaces del_timer[_sync](). Convert the whole tree
over and remove the historical wrapper inlines.
Conversion was done with coccinelle plus manual fixups where necessary.
Signed-off-by: Thomas Gleixner <[email protected]>
Signed-off-by: Ingo Molnar <[email protected]>
Currently, per-radio attributes are set on per-phy basis, i.e., all the
radios present in a wiphy will take attributes values sent from user. But
each radio in a wiphy can get different values from userspace based on
its requirement.
To extend support to set per-radio attributes, add support to get radio
index from userspace. Add an NL attribute - NL80211_ATTR_WIPHY_RADIO_INDEX,
to get user specified radio index for which attributes should be changed.
Pass this to individual drivers, so that the drivers can use this radio
index to change per-radio attributes when necessary. Currently, per-radio
attributes identified are:
NL80211_ATTR_WIPHY_TX_POWER_LEVEL
NL80211_ATTR_WIPHY_ANTENNA_TX
NL80211_ATTR_WIPHY_ANTENNA_RX
NL80211_ATTR_WIPHY_RETRY_SHORT
NL80211_ATTR_WIPHY_RETRY_LONG
NL80211_ATTR_WIPHY_FRAG_THRESHOLD
NL80211_ATTR_WIPHY_RTS_THRESHOLD
NL80211_ATTR_WIPHY_COVERAGE_CLASS
NL80211_ATTR_TXQ_LIMIT
NL80211_ATTR_TXQ_MEMORY_LIMIT
NL80211_ATTR_TXQ_QUANTUM
By default, the radio index is set to -1. This means the attribute should
be treated as a global configuration. If the user has not specified any
index, then the radio index passed to individual drivers would be -1. This
would indicate that the attribute applies to all radios in that wiphy.
Signed-off-by: Roopni Devanathan <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Johannes Berg <[email protected]>
The buf_len is used to limit the iterations for retrieving the country
power setting and may underflow under certain conditions due to changes
in the power table in CLC.
This underflow leads to an almost infinite loop or an invalid power
setting resulting in driver initialization failure.
Cc: [email protected]
Fixes: fa6ad88e023d ("wifi: mt76: mt7921: fix country count limitation for CLC")
Signed-off-by: Leon Yen <[email protected]>
Signed-off-by: Ming Yen Hsieh <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
MediaTek has asked to switch from the ISC license to BSD-3-Clause-Clear,
in order to improve clarity and the legal integrity of the code.
The BSD-3-Clause license includes the "no endorsement" clause, which is
important for protecting the reputation of the original authors and
contributors by preventing unauthorized use of their names for endorsement
purposes.
This clause is absent in the BSD-2-Clause license, which is more permissive
but lacks this specific protection.
This change also cleans up the license of some Kconfig/Makefile files,
which were accidentally marked as GPL.
The GPL 2.0 remains in use on mt76x0, as well as two source files in mt7615
for which the license situation still needs to be clarified.
Signed-off-by: Felix Fietkau <[email protected]>
mt76_eeprom_override has of_get_mac_address, which can return
-EPROBE_DEFER if the nvmem driver gets loaded after mt76 for some
reason.
Make sure this gets passed to probe so that nvmem mac overrides always
work.
Signed-off-by: Rosen Penev <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Embedding net_device into structures prohibits the usage of flexible
arrays in the net_device structure. For more details, see the discussion
at [1].
Un-embed the net_devices from struct mt76_dev by converting them
into pointers, and allocating them dynamically. Use the leverage
alloc_netdev_dummy() to allocate the net_device object at
mt76_dma_init().
The free of the device occurs at mt76_dma_cleanup().
Link: https://lore.kernel.org/all/[email protected]/ [1]
Reviewed-by: Simon Horman <[email protected]>
Signed-off-by: Breno Leitao <[email protected]>
Acked-by: Kalle Valo <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
Any station configured with an AID over 20 causes a firmware crash.
This situation occurred in our testing using an AP interface on 7922
hardware, with a modified hostapd, sourced from Mediatek's OpenWRT
feeds.
In stock hostapd, station AIDs begin counting at 1, and this
configuration is prevented with an upper limit on associated stations.
However, the modified hostapd began allocation at 65, which caused the
firmware to crash. This fix does not allow these AIDs to work, but will
prevent the firmware crash.
This crash was only seen on IFTYPE_AP interfaces, and the fix does not
appear to have an effect on IFTYPE_STATION behavior.
Fixes: 5c14a5f944b9 ("mt76: mt7921: introduce mt7921e support")
Signed-off-by: Rory Little <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Enable 160MHz beamformee support on mt7922 by updating HE capability
element configuration. Previously, only 160MHz channel width was set,
but beamformee for 160MHz was not properly advertised. This patch
adds BEAMFORMEE_MAX_STS_ABOVE_80MHZ_4 capability to allow devices
to utilize 160MHz BW for beamforming.
Tested by connecting to 160MHz-bandwidth beamforming AP and verified
HE capability.
Signed-off-by: Quan Zhou <[email protected]>
Link: https://patch.msgid.link/ae637afaffed387018fdc43709470ef65898ff0b.1756383627.git.quan.zhou@mediatek.com
Signed-off-by: Felix Fietkau <[email protected]>
When station mode, don't disconnect when we get
channel switch from AP to DFS channel. Most APs
send CSA request after pass background CAC. In other
case we should disconnect after detect beacon miss.
Without patch when we get CSA to DFS channel get:
"kernel: wlo1: preparing for channel switch failed, disconnecting"
Signed-off-by: Janusz Dziedzic <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Several places use rcu_dereference to get a wcid entry without validating
if the index exceeds the array boundary. Fix this by using a helper function,
which handles validation.
Signed-off-by: Felix Fietkau <[email protected]>
The decap offload configuration should only be applied after the STA has
been successfully initialized. Attempting to configure it earlier can lead
to corruption of the MAC configuration in the chip's hardware state.
Add an early check for `msta->deflink.wcid.sta` to ensure the station peer
is properly initialized before proceeding with decapsulation offload
configuration.
Cc: [email protected]
Fixes: 24299fc869f7 ("mt76: mt7921: enable rx header traslation offload")
Signed-off-by: Deren Wu <[email protected]>
Link: https://patch.msgid.link/f23a72ba7a3c1ad38ba9e13bb54ef21d6ef44ffb.1748149855.git.deren.wu@mediatek.com
Signed-off-by: Felix Fietkau <[email protected]>
Some countries have strict RF restrictions where changing the regulatory
domain dynamically based on the connected AP is not acceptable.
This patch disables Beacon country IE hinting when a valid country code
is set from usersland (e.g., by system using iw or CRDA).
Signed-off-by: Leon Yen <[email protected]>
Signed-off-by: Ming Yen Hsieh <[email protected]>
Tested-by: David Ruth <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
mt76 does a lot of:
local_bh_disable();
napi_enable(...napi);
napi_schedule(...napi);
local_bh_enable();
local_bh_disable() is not a real lock, its most likely taken
because napi_schedule() requires that we invoke softirqs at
some point. napi_enable() needs to take a mutex, so move it
from under the BH protection.
Fixes: 413f0271f396 ("net: protect NAPI enablement with netdev_lock()")
Reported-by: Dan Carpenter <[email protected]>
Link: https://lore.kernel.org/[email protected]
Reviewed-by: Eric Dumazet <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
This bug was noticed by me and confirmed by many more people using this
chipset with openwrt: https://github.com/openwrt/mt76/issues/783
It seems that for this particular chipset the mt76_phy->txpower_cur is
never set, like in the case of other chipsets like mt7603, mt7615, etc.
The driver is correctly calculating the TX power adjustment based on the
number of antennas. However, the base TX power (phy->txpower_cur) is not
being properly initialized or set to a meaningful value. It's starting
at 0, so the final result is just the antenna gain compensation divided
by 2.
Signed-off-by: Razvan Grigore <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
When the system suspend or resume, the WiFi driver sends
an hif_ctrl command to the firmware and waits for an event.
Due to changes in the event format reported by the chip, the
current mt7925's driver does not account for these changes,
resulting in command timeout. Add flow to handle hif_ctrl
event to avoid command timeout. We also exented API
mt76_connac_mcu_set_hif_suspend for connac3 this time.
Signed-off-by: Quan Zhou <[email protected]>
Link: https://patch.msgid.link/3a0844ff5162142c4a9f3cf7104f75076ddd3b87.1735910562.git.quan.zhou@mediatek.com
Signed-off-by: Felix Fietkau <[email protected]>
Add CSA (Channel Switch Announcement) related implementation
in collaboration with mac80211 to deal with dynamic channel
switching.
Signed-off-by: Leon Yen <[email protected]>
Signed-off-by: Ming Yen Hsieh <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This commit extends the `mt76_connac_mcu_uni_add_dev` function to include
support for Multi-Link Operation (MLO). Additionally, backward
compatibility for MT7921 is preserved, enabling seamless integration with
existing setups.
Fixes: 86c051f2c418 ("wifi: mt76: mt7925: enabling MLO when the firmware supports it")
Signed-off-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Fixes linked list management issues during restart, where sta entries
can be recreated and reinitialized while still in the poll list, triggering
kernel warnings.
Signed-off-by: Felix Fietkau <[email protected]>
The maximum command quota of the firmware may be exceeded because the
command to retrieve the quota setting has not been taken into account.
This patch considers not only the quota usage of the command retrieving
quota settings but also limits the total quota usage.
Signed-off-by: Leon Yen <[email protected]>
Signed-off-by: Ming Yen Hsieh <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
The check should start from 5845 to 5925, which includes
channels 169, 173, and 177.
Fixes: 09382d8f8641 ("wifi: mt76: mt7921: update the channel usage when the regd domain changed")
Signed-off-by: Ming Yen Hsieh <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Also report auth/disassoc events, in order to give the driver more control over
handling the station state.
Signed-off-by: Felix Fietkau <[email protected]>
This allows the core code to change the channel. Code deduplication and
preparation for adding scanning code to the core.
Signed-off-by: Felix Fietkau <[email protected]>
