If efuse mode is used, read all values from fw during eeprom init,
which makes it more convinient to check if rf values in efuse are
properly burned.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
- Remove no-op code for queue lock/unlock, which is no longer needed
- Set a missing DMA flag
- Wait for full completion of error recovery before restarting tx
- Schedule IRQ tasklet to ensure that IRQ mask gets written
Signed-off-by: Felix Fietkau <[email protected]>
Firmware functions (SCS, MU ...) also require read-clear phy counters,
hence firmware prepares a global task to read shared fields out to a
shared pool to avoid concurrency. Switch to event format accordingly.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Get per-rate txpower with mcu command. This is the preparation of
co-driver for the next chipset, which has different tmac power registers
but can share this same command.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
It's much more accurate than .get_tsf + .set_tsf, and switch to use
mt76_rmw to operate tsf registers.
Tested-by: Xing Song <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Thermal cooling device support is added to control the temperature by
throttling the data transmission for the given duration. Throttling is
done by adjusting Tx period by given percentage of time. The thermal
device allows user to configure duty cycle.
Throttling can be disabled by setting the duty cycle to 0. The cooling
device can be found under /sys/class/thermal/cooling_deviceX/.
Corresponding soft link to this device can be found under phy folder
To set duty cycle as 80%,
echo 80 > /sys/class/ieee80211/phy*/cooling_device/cur_state
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This provides userspace with a unified interface, hwmon sysfs, to monitor
temperature in the hardware and can be adapted to system monitoring tools.
For reading temperature, cat /sys/class/ieee80211/phy*/hwmon*/temp1_input
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
There are firmware or hardware issues, which are currently causing tx hangs
when attempting to use these interfaces
Signed-off-by: Felix Fietkau <[email protected]>
Add runtime configuration for bitrate mask. This update firmware rate
control to add a boundary on top of table to limit the rate selection
for each peer, so when user set bitrates vht-mcs-5 1:9, which actually
means nss = 1 mcs = 0~9. This only applies to data frames as for other
mgmt, mcast, bcast still use legacy rates as it is.
Note that driver does not support GI configuration.
Example:
iw dev wlan0 set bitrates vht-mcs-5 1:9 he-mcs-5 2:7
iw dev wlan0 set bitrates legacy-5 6 he-mcs-5 2:0-11
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove obsoleted codes. This is the preparation for .set_bitrate_mask().
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
"idx" needs to be signed for the error handling to work.
Fixes: 495184ac91bb ("mt76: mt7915: add support for applying pre-calibration data")
Signed-off-by: Dan Carpenter <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Instead of attaching the last reported rate to tx packets, use
ieee80211_tx_status_ext to immediately pass the rate to mac80211 after
receiving it from the firmware.
Preparation for implementing full tx status reporting
Signed-off-by: Felix Fietkau <[email protected]>
In order to remove duplicated code, move mt76_token_init in
mt76_alloc_device routine
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Precision %.*s was intended instead of width %*s. The original code
will still print unintended data from beyond the end of skb->data.
Fixes: 665b2c780d63 ("mt76: mt7915: limit firmware log message printk to buffer length")
Signed-off-by: Dan Carpenter <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Do not read rf value from efuse when driver is configured to
use flash mode.
Tested-by: Bruce Chuang <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move token management in mt76 common module since it is shared between
mt7615, mt7915 and mt7921 drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move token_lock, token and token_count data structures in mt76_dev.
This is a preliminary patch to move token management in mt76 common
module since it is shared by mt7615, mt7915 and mt7921 drivers.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add the capability to define a custom rx napi callback for each driver.
This is a preliminary patch to properly support runtime-pm on rx side
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Junlin Yang <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Since driver no longer handler per-rate tx power setting, we need to
read the power values directly from registers.
Tested-by: Evelyn Tsai <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Clean up the flow of per-rate txpower limit setting to get rid of
duplicate work since it has already been handled by firmware, and set
proper max_power based on different channels and regdomains.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Dump mcu command code in hex and related prefix to help debugging
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When the EEPROM data is read from flash, it can contain pre-calibration
data, which can save calibration time.
Note that group_cal can save 30% bootup calibration time, and dpd_cal can
save 75% channel switching time.
Tested-by: Bo Jiao <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
After DMA reset, tx status information for queued frames will never arrive.
Flush the queue to free skbs immediately instead of waiting for a timeout
Signed-off-by: Felix Fietkau <[email protected]>
In mt7915_mac_reset_work(), make sure freeing skbs after mt7915_dma_reset().
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt7915_tx_token_put() should get call before mt76_free_pending_txwi().
Fixes: f285dfb98562 ("mt76: mt7915: reset token when mac_reset happens")
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix ofdm rate index and ldpc setting in rate setting field of tx
descriptor.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rework mt7915_tm_set_tx_len() with mt76_testmode_alloc_skb() to support
larger packet based on a longer tx_time.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add mmio.c in order to use mt76_bus_ops throughout the driver.
It will be also shared with the future APSoC revision.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Frame reception timestamp (low 32-bits) that indicates the value of the
local TSF timer value at the time the first bit of the MAC header in the
received frame (PPDU unit) arriving at the MAC.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Reset wifi subsystem when MCU is already running.
Fixes firmware download failure after soft reboot on systems where the PCIe
reset could not be performed properly.
Signed-off-by: Ryder Lee <[email protected]>
Co-developed-by: Felix Fietkau <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
ieee80211_beacon_get_template() returns NULL when beacon state is disabled.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The same as mt7615. Keep BSS_INFO_BASIC enabled throughout interfaces
life cycle.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When disassociating and clearing the BSSID of a repeater entry used by a client
mode interface, the corresponding MAC address entry can get lost too, causing
the client interface to not be able to associate anymore.
Fix this by also refreshing the MAC address when setting the BSSID
Signed-off-by: Felix Fietkau <[email protected]>
Deleting a key with the previous key index deletes the current key
Rework the code to better keep track of multiple keys and check for the
key index before deleting the current key
Signed-off-by: Felix Fietkau <[email protected]>
