The commit 22b980badc0f ("mt76: add functions for parsing rate power limits
from DT") introduced generic support for rates limits in the devicetree.
But the mt7915 supports beamforming and has another table for configuring
the backoff limits. These can be configured in the DT with the paths-*
properties. The path-*-bf are the ones relevant for beamforming and the
ones without -bf suffix for "traditional" path backoff.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Sven Eckelmann (Plasma Cloud) <[email protected]>
Link: https://patch.msgid.link/20251007-backoff-table-support-v3-3-fd6e2684988f@simonwunderlich.de
Signed-off-by: Felix Fietkau <[email protected]>
MediaTek has asked to switch from the ISC license to BSD-3-Clause-Clear,
in order to improve clarity and the legal integrity of the code.
The BSD-3-Clause license includes the "no endorsement" clause, which is
important for protecting the reputation of the original authors and
contributors by preventing unauthorized use of their names for endorsement
purposes.
This clause is absent in the BSD-2-Clause license, which is more permissive
but lacks this specific protection.
This change also cleans up the license of some Kconfig/Makefile files,
which were accidentally marked as GPL.
The GPL 2.0 remains in use on mt76x0, as well as two source files in mt7615
for which the license situation still needs to be clarified.
Signed-off-by: Felix Fietkau <[email protected]>
The definition of MT_RX_SEL (for rdd_rx_sel) is mixed with the
definition of HWRDD idx.
For example, MT_RX_SEL2 is for background HWRDD idx, not an option
of rdd_rx_sel.
Therefore, add mt7915_get_rdd_idx as a helper function to get the
HWRDD idx for each variants.
Additionally, remove some parts of the code inherited from the legacy
chips.
For instance,
1. rdd_state is used for single-band-dual-HWRDD chips (for 80+80),
especially the 76xx series.
2. rdd_rx_sel is also used for single-band-dual-HWRDD chips
rx_sel = 0 => RDD0 for WF0, RDD1 for WF2
rx_sel = 1 => RDD0 for WF1, RDD1 for WF3
Chip Variants | 5G rdd idx(=bandidx)| Background rdd idx
-------------------------------|---------------------|-------------------
MT7915A | 0 | 2
MT7915D | 1 | 2
MT7916 2G + 5G (2T2R+1R) | 1 | 2
MT7916 2G + 5G (3T3R) | 1 | N/A
MT7981 2G + 5G | 1 | N/A
MT7986 2G + 5G (one adie DBDC) | 1 | N/A
MT7986 5G (one adie) | 1 (bandidx=MT_BAND1)| N/A
MT7986 2G + 5G (dual adie) | 1 | N/A
Signed-off-by: StanleyYP Wang <[email protected]>
Reviewed-by: Shayne Chen <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Refactor for making use of mt76_get_power_bound instead of the specific
mt7915_get_power_bound, since we need this for other chipsets as well
when calculating txpower
Signed-off-by: Razvan Grigore <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
-Wflex-array-member-not-at-end was introduced in GCC-14, and we are
getting ready to enable it, globally.
So, in order to avoid ending up with a flexible-array member in the
middle of multiple other structs, we use the `struct_group_tagged()`
helper to create a new tagged `struct mt76_connac2_mcu_rxd_hdr`.
This structure groups together all the members of the flexible
`struct mt76_connac2_mcu_rxd` except the flexible array.
As a result, the array is effectively separated from the rest of the
members without modifying the memory layout of the flexible structure.
We then change the type of the middle struct members currently causing
trouble from `struct mt76_connac2_mcu_rxd` to `struct
mt76_connac2_mcu_rxd_hdr`.
We also want to ensure that when new members need to be added to the
flexible structure, they are always included within the newly created
tagged struct. For this, we use `static_assert()`. This ensures that the
memory layout for both the flexible structure and the new tagged struct
is the same after any changes.
This approach avoids having to implement `struct mt76_connac2_mcu_rxd_hdr`
as a completely separate structure, thus preventing having to maintain
two independent but basically identical structures, closing the door
to potential bugs in the future.
So, with these changes, fix the following warnings:
drivers/net/wireless/mediatek/mt76/mt7915/mcu.h:32:37: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/mediatek/mt76/mt7915/mcu.h:40:37: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/mediatek/mt76/mt7915/mcu.h:49:37: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/mediatek/mt76/mt7915/mcu.h:58:37: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
Signed-off-by: Gustavo A. R. Silva <[email protected]>
Link: https://patch.msgid.link/Zr5KsZugaEXrApQJ@elsanto
Signed-off-by: Felix Fietkau <[email protected]>
The power gain value is related to total TX path, so change the
calculation to use per-phy chainmask.
Signed-off-by: Allen Ye <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Enable RED to limit the number of token used by each band. If single band
uses too many tokens, it would hurt the throughput of the other bands.The
software path can solve this problem by AQL so enable RED for HW path only.
Reviewed-by: Shayne Chen <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This power should override the per bandwidth max power that the
device emits.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add a helper for common boundary check. This is a preliminary patch
to add per bandwidth power control.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This adds support for adjusting the Txpower level while pushing
traffic to an associated station. The allowed range is from 0 to
the maximum power of channel.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The SPR parameter set comprises OBSS PD threshold for SRG and
non SRG and Bitmap of BSS color and partial BSSID. This adds
support to configure fields of SPR element to firmware.
User can disable firmware SR algorithms by turning sr_scene_detect off.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Trigger firmware crash and enable full system recovery through debugfs.
This also renames knob "fw_ser" to a clear-cut name "sys_recovery".
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The MIB INFO command is fetching MIB_BUSY_TIME, MIB_TX_TIME, MIB_RX_TIME and
MIB_OBSS_AIRTIME from the radio and filling out cc_busy, cc_tx, cc_bss_rx
and cc_rx respectively.
busy should be >= tx + rx >= tx + bss_rx but we don’t always quite see this.
Sometimes tx + rx is a bit higher than busy due to inaccurate accounting,
so this patch recalculates numbers to make them more reasonable.
Reported-By: Kevin Schneider <[email protected]>
Tested-by: Kevin Schneider <[email protected]>
Tested-by: Chad Monroe <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In previous, we only allow user to configure tx antenna mask
contiguously (e.g. 0x3, 0xf).
This patch allows user to configure tx antenna mask interleavingly
(e.g. 0x5, 0x8). By setting proper antenna mask and nss, user can
prioritized the signal of different antennas, which helps to test
their performance in normal mode.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Since an in-band discovery frame is offloaded by MCU,
here we enlarge the command size to accommodate the additional content.
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Money Wang <[email protected]>
Signed-off-by: MeiChia Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76_connac2_mcu_fill_message routine in shared module in order to
reuse it for mt7921 and mt7915e drivers. This is a preliminary patch to
add mt7990 driver support.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to add mt7990 chipset support.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
1. get status of system recovery from firmware.
2. add more recovery points.
3. make knob per phy.
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt7915_mcu_rdd_background_enable and
mt7915_mcu_background_chain_ctrl routines to configure rx dfs dedicated chain.
This is a preliminary patch to add zero-wait dfs support performing CAC
detection on rdd2.
Tested-by: Owen Peng <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Without this change, it sends the wrong SMPS mode to firmware
when a station sends an action frame with disabled SMPS.
Fixes: 427b09cd6bfa ("mt76: mt7915: fix SMPS operation fail")
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: MeiChia Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Load the default eeprom data when the content of flash/efuse is invalid.
This could help to eliminate some issues due to incorrect or
insufficient rf values.
Co-developed-by: Bo Jiao <[email protected]>
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
TGn fails sending SM power save mode action frame to the AP to switch
from dynamic SMPS mode to static mode.
Reported-by: Fang Zhao <[email protected]>
Signed-off-by: Fang Zhao <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add debugfs knobs to read MCU utilization, which helps user know
firmware status more easily to narrow down CPU bottleneck issues.
Co-developed-by: Ryder Lee <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
With this patch, driver can support single rate, (HE)GI and HE_LTF
configuration through .set_bitrate_mask().
Tested-by: MeiChia Chiu <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Enable HE UL MU-MIMO in sta_rec_muru, which works on both ap and station
mode.
For sending trigger frames, one of the conditions fw uses is to check if
mib rx airtime meets the threshold.
There's a main control of mib rx airtime report register in fw, so we
need to enable the register by mcu cmd instead of directly writing it,
otherwise it will still be disabled by fw.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rework starec tags to the order which firmware expected. This also fixes
some weird behaviors during generating SPL of HE-MU.
Co-developed-by: Ryder Lee <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
With this patch we can append txbf starec TLVs. This is an intermediate
patch to improve HE MUMIMO performances.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mcu APIs to configure bss coloring and to report bss coloring
collisions. Add support to report coloring countdown in beacon sent by
the device.
Co-developed-by: Ryder Lee <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Switch proper tx arbiter mode during testmode tx to prevent from
entering the flow of normal tx in FW.
Also, testmode SU and MU tx need to use different arbiter mode.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Report tx rate from tx status packets instead of receving periodic mcu
event. This improves flexibility, accuracy and AQL performance, and
simplifies code flow for better readability.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The newer firmware requires host driver to set BA winsize
on both Tx/Rx sessions, so modify it for the long run.
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Sujuan Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:114:10: error: implicit
conversion from enumeration type 'enum mt76_cipher_type' to different
enumeration type 'enum mcu_cipher_type' [-Werror,-Wenum-conversion]
return MT_CIPHER_NONE;
~~~~~~ ^~~~~~~~~~~~~~
drivers/net/wireless/mediatek/mt76/mt7921/mcu.c:114:10: error: implicit
conversion from enumeration type 'enum mt76_cipher_type' to different
enumeration type 'enum mcu_cipher_type' [-Werror,-Wenum-conversion]
return MT_CIPHER_NONE;
~~~~~~ ^~~~~~~~~~~~~~
Fixes: c368362c36d3 ("mt76: fix iv and CCMP header insertion")
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The iv from RXD is only for TKIP_RSC/CCMP_PN/GCMP_PN, and it needs a
check for CCMP header insertion. Move mt76_cipher_type to mt76.h to
reduce duplicated code.
Signed-off-by: Xing Song <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use mt7915_mcu_set_txbf() to reduce global functions. This can be
easily extended to support other TxBF commands in further patches.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
