Run mt76_free_device instead of ieee80211_free_hw if device probing
fails in order to remove the already allocated mt76 workqueue
Fixes: a86f1d01f5ce5 ("mt76: move mt76 workqueue in common code")
Fixes: f1d962369d568 ("mt76: mt7915: implement HE per-rate tx power support")
Signed-off-by: Lorenzo Bianconi <[email protected]>
If THIS_MODULE is not set, the module would be removed while debugfs is
being used.
It eventually makes kernel panic.
Fixes: e57b7901469f ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets")
Signed-off-by: Taehee Yoo <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
If THIS_MODULE is not set, the module would be removed while debugfs is
being used.
It eventually makes kernel panic.
Fixes: ec9742a8f38e ("mt76: mt7915: add .sta_add_debugfs support")
Signed-off-by: Taehee Yoo <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When per-packet rate reporting is enabled, the hardware can get stuck under
some conditions. It self-recovers quickly, but in practice this leads to
reduced performance.
In order to avoid running into this issue, disable per-packet rate reporting
by default and query the rx rate from firmware instead, unless monitor mode
is enabled.
Signed-off-by: Felix Fietkau <[email protected]>
The firmware/hardware supports only 16 entries. Trying to use more can lead
to timeouts on some firmware versions
Signed-off-by: Felix Fietkau <[email protected]>
Read per-stream measurements every 100 ms and build a simple moving average.
Tested-by: Shayne Chen <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In the MT7915 info, the fields for the WLAN index / queue overlap with the
token id, and the MT_TX_FREE_PAIR bit indicates, which one is present.
If MT_TX_FREE_PAIR is set, skip processing the token index, since the data
will not be valid.
This fixes accidentally freeing tokens which are still in use by the
hardware with a wrong station pointer.
Signed-off-by: Felix Fietkau <[email protected]>
When looking for a MAC address slot, start by using main BSSID slots 1-3,
afterwards use 16 repeater mode BSSID slots, then start using the slots
usually used for AP mode.
This search order should prevent unnecessary conflicts with AP mode interfaces
on the same PHY
Signed-off-by: Felix Fietkau <[email protected]>
Convert cpu_to_le16(le16_to_cpu(E1) + E2) to use le16_add_cpu().
Signed-off-by: Liu Shixin <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Release mcu message memory in case of failure in mt7915_mcu_add_beacon
routine
Fixes: e57b7901469fc ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Avoid firmware falling into spectrum mode since that will set
unexpected PSE/PLE thresholds which lead to Tx hang.
This mode should be cleaned before firmware download stage.
Signed-off-by: Chih-Min Chen <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Since the switch to using AQL by default, mtxq->retry_q is never filled anymore
Remove it to get rid of a few more unnecessary cycles in the tx path
Signed-off-by: Felix Fietkau <[email protected]>
Compared to mac80211 ACs, MT7915 queue numbers are in reverse order
There is no need for the defensive WARN_ON_ONCE, so we can simplify
the function to avoid the array lookup
Signed-off-by: Felix Fietkau <[email protected]>
Now that AQL works well on all mt76 drivers, completely replace the arbitrary
burst sizing and number of bursts logic for tx scheduling.
For the short period of time in which AQL does not work well yet, limit each
stations to 16 in-flight packets that have no estimated tx time.
This should avoid filling the queue if a station connects and queues up a
large number of packets before rate control information is available, especially
with hardware rate control
Signed-off-by: Felix Fietkau <[email protected]>
On 7615 and newer, DMA completion only triggers unmap, but not free of queued
skbs, since pointers to packets are queued internally.
Because of that, there is no need to process the main data queue immediately
on DMA completion.
To improve performance, mask out the DMA data queue completion interrupt and
process the queue only when we receive a txfree event.
This brings the number of interrupts under load down to a small fraction.
Signed-off-by: Felix Fietkau <[email protected]>
The previous scheduling round may have been limited by AQL.
More frames might be available after the tx free run.
Signed-off-by: Felix Fietkau <[email protected]>
Since DMA completion does not imply tx completion, it makes more sense to
poll for airtime from mt7915_mac_tx_free.
Reduce the runtime of the function by moving all items from dev->sta_poll_list
to a local list once and process any stations that were added afterwards
on the next run
Signed-off-by: Felix Fietkau <[email protected]>
- change the WTBL LMAC access function to set the mapping window only once
- use ac * 2 as offset, since each AC has separate words for rx and tx
Signed-off-by: Felix Fietkau <[email protected]>
Using dev_kfree_skb for tx skbs breaks AQL. This worked until now only
by accident, because a mac80211 issue breaks AQL on drivers with firmware
rate control that report the rate via ieee80211_tx_status_ext as struct
rate_info.
Signed-off-by: Felix Fietkau <[email protected]>
