mt76 does a lot of:
local_bh_disable();
napi_enable(...napi);
napi_schedule(...napi);
local_bh_enable();
local_bh_disable() is not a real lock, its most likely taken
because napi_schedule() requires that we invoke softirqs at
some point. napi_enable() needs to take a mutex, so move it
from under the BH protection.
Fixes: 413f0271f396 ("net: protect NAPI enablement with netdev_lock()")
Reported-by: Dan Carpenter <[email protected]>
Link: https://lore.kernel.org/[email protected]
Reviewed-by: Eric Dumazet <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
When the system suspend or resume, the WiFi driver sends
an hif_ctrl command to the firmware and waits for an event.
Due to changes in the event format reported by the chip, the
current mt7925's driver does not account for these changes,
resulting in command timeout. Add flow to handle hif_ctrl
event to avoid command timeout. We also exented API
mt76_connac_mcu_set_hif_suspend for connac3 this time.
Signed-off-by: Quan Zhou <[email protected]>
Link: https://patch.msgid.link/3a0844ff5162142c4a9f3cf7104f75076ddd3b87.1735910562.git.quan.zhou@mediatek.com
Signed-off-by: Felix Fietkau <[email protected]>
When enter suspend/resume while in a connected state, the upper layer
will trigger disconnection before entering suspend, and at the same time,
it will trigger regd_notifier() and update CLC, causing the CLC event to
not be received due to suspend, resulting in a command timeout.
Therefore, the update of CLC is postponed until resume, to ensure data
consistency and avoid the occurrence of command timeout.
Signed-off-by: Quan Zhou <[email protected]>
Link: https://patch.msgid.link/bab00a2805d0533fd8beaa059222659858a9dcb5.1735910455.git.quan.zhou@mediatek.com
Signed-off-by: Felix Fietkau <[email protected]>
In multi-channel scenarios, the granted channel must be aborted before
suspending. Otherwise, the firmware will be put into a wrong state,
resulting in an association failure after resuming.
With this patch, the granted channel will be aborted before suspending
if necessary.
Cc: [email protected]
Fixes: c948b5da6bbe ("wifi: mt76: mt7925: add Mediatek Wi-Fi7 driver for mt7925 chips")
Signed-off-by: Michael Lo <[email protected]>
Signed-off-by: Ming Yen Hsieh <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Also report auth/disassoc events, in order to give the driver more control over
handling the station state.
Signed-off-by: Felix Fietkau <[email protected]>
From commit a304e1b82808 ("[PATCH] Debug shared irqs"), there is a test
to make sure the shared irq handler should be able to handle the unexpected
event after deregistration. For this case, let's apply MT76_REMOVED flag to
indicate the device was removed and do not run into the resource access
anymore.
Fixes: c948b5da6bbe ("wifi: mt76: mt7925: add Mediatek Wi-Fi7 driver for mt7925 chips")
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
A sub-process of Wifi L0.5 reset will make chip common partition
enter low power, and have chance lead to Bluetooth host-to-chip
command timeout, modify the software flow according to the chip's
design to solve the problem.
Fixes: c948b5da6bbe ("wifi: mt76: mt7925: add Mediatek Wi-Fi7 driver for mt7925 chips")
Signed-off-by: Quan Zhou <[email protected]>
Signed-off-by: Ming Yen Hsieh <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mtk_wed_device pointer in mt76_queue structure in order to
configure WED chip.
Get rid of dev parameter in Q_READ and Q_WRITE macros.
Introduce wed parameter to the following routine signatures:
- mt76_init_queue
- mt76_init_tx_queue
This is a preliminary patch to introduce WED support for mt7996 since
mt7996 runs two separate WED chips.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add mt7925, a new mac80211 driver for the MediaTek Wi-Fi 7 (802.11be) device
Filogic 360, which can support Station, AP, P2P, and monitor modes.
Filogic 360 supports max 4096-QAM/160MHz radio operation at 6 GHz, 5 GHz,
or 2.4 GHz with 2x2 antennas. This chip supports PCIe and USB bus type.
mt7925 supports Wi-Fi 6E and EHT rate with single link only at this moment,
whereas Wi-Fi 7 and its specific features are working in progress. They will be
introduced in further patches.
The driver is build tested by Intel's kernel test robot with both GCC and Clang
with several architecture. Sparse reports no warnings.
There are multiple authors, they are listed in alphabetical order below.
Co-developed-by: Hao Zhang <[email protected]>
Signed-off-by: Hao Zhang <[email protected]>
Co-developed-by: Leon Yen <[email protected]>
Signed-off-by: Leon Yen <[email protected]>
Co-developed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Co-developed-by: Mingyen Hsieh <[email protected]>
Signed-off-by: Mingyen Hsieh <[email protected]>
Co-developed-by: Nelson Yu <[email protected]>
Signed-off-by: Nelson Yu <[email protected]>
Co-developed-by: Quan Zhou <[email protected]>
Signed-off-by: Quan Zhou <[email protected]>
Co-developed-by: Rong Yan <[email protected]>
Signed-off-by: Rong Yan <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
