For AP and Client mode, the hardware can pass received packets as 802.3 frames
that can be passed to the network stack as-is.
Signed-off-by: Felix Fietkau <[email protected]>
Enable hw rx-amsdu de-aggregation support available in 7915 devices.
This is a preliminary patch to enable rx checksum offload
Signed-off-by: Lorenzo Bianconi <[email protected]>
With this patch, TxBF can be run on both bands simultaneously.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add ht/vht implicit Tx beamforming support and enable it via debugfs.
Tested-by: Shayne Chen <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move chainmask from driver phy to mt76_phy since it is used by all
drivers. This is a preliminary patch to create a common mcu library used
by mt7615 and mt7921 drivers
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mac_work delayed_work and mac_work_count in mt76_phy since it is
used by all drivers. This is a preliminary patch to create a common mcu
library used by mt7615 and mt7921 drivers
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Reset buffering token in mt7915_mac_reset_work() to avoid possible leakege,
which leads to Tx stop after mac reset.
Tested-by: Bo Jiao <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt7915 automatically detects dbdc feature so drop debugfs knob.
Move if_comb, mt7915_rates, if_limits structs and mt7915_regd_notifier(),
mt7915_init_wiphy() routines at the begging of init.c in order to make
mt7915_register_ext_phy routine static
Co-developed-by: Shayne Chen <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Co-developed-by: Ryder Lee <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt7915 dbdc support. If dbdc is available, mt7915 primary phy
will work on 2.4GHz band, while secondary one on 5GHz band.
Co-developed-by: Shayne Chen <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Co-developed-by: Ryder Lee <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to introduce dbdc support to mt7915 devices
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to move properly support mt7915 dbdc
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Support testmode tx for MT7915A, including tx streams and HE rate
settings.
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When per-packet rate reporting is enabled, the hardware can get stuck under
some conditions. It self-recovers quickly, but in practice this leads to
reduced performance.
In order to avoid running into this issue, disable per-packet rate reporting
by default and query the rx rate from firmware instead, unless monitor mode
is enabled.
Signed-off-by: Felix Fietkau <[email protected]>
When looking for a MAC address slot, start by using main BSSID slots 1-3,
afterwards use 16 repeater mode BSSID slots, then start using the slots
usually used for AP mode.
This search order should prevent unnecessary conflicts with AP mode interfaces
on the same PHY
Signed-off-by: Felix Fietkau <[email protected]>
Avoid firmware falling into spectrum mode since that will set
unexpected PSE/PLE thresholds which lead to Tx hang.
This mode should be cleaned before firmware download stage.
Signed-off-by: Chih-Min Chen <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Using dev_kfree_skb for tx skbs breaks AQL. This worked until now only
by accident, because a mac80211 issue breaks AQL on drivers with firmware
rate control that report the rate via ieee80211_tx_status_ext as struct
rate_info.
Signed-off-by: Felix Fietkau <[email protected]>
Queueing a per-sta work item from the tx free path can become very expensive
under load. This work is only supposed to pull rate control stats every
second and deal with rate control changes.
Additionally, the rate control update code was wrong, because it was
confusing bit masks and bit numbers in test_bit.
Fix this by introducing a dedicated device work item for rate control
updates, and by polling station stats from the phy mac work.
Stations requiring polling or rate control updates are added to lists
protected by dev->sta_poll_lock.
Signed-off-by: Felix Fietkau <[email protected]>
Clean up the flow of per-rate txpower limit setting to get rid of
dulplicate work since it has already been handled by firmware, and set
proper max_power based on different channels and regdomains.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix a NULL pointer dereference in mt7915_register_ext_phy since phy
data structure is allocated by mt76_alloc_phy routine
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
make mac_work per phy instead of per device and fix a possible deadlock
in mt7915_stop since mt7915_mac_work runs holding mt76 mutex
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Enable TxBF modules and trigger sounding process to support Tx beamformer.
Signed-off-by: Ryder Lee <[email protected]>
Tested-by: Evelyn Tsai <[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
The capabilities for the HE interfaces are generated from the capabilities
reported by the firmware.
This should move to common file once we got other HE devices support.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add support for the MediaTek latest generation IEEE 802.11ax 4x4
device MT7915E, which supports concurrent dual-band operation at
both 5GHz and 2.4GHz.
Note that this patch just add basic part and will add more HE
capabilities support in the further patches.
The driver supports AP, Station, Mesh and monitor mode.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Chih-Min Chen <[email protected]>
Suggested-by: Shihwei Lin <[email protected]>
Tested-by: Evelyn Tsai <[email protected]>
Acked-by: Yiwei Chung <[email protected]>
Acked-by: YF Luo <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
