Run mt76x0 tssi calibration process if enabled in eeprom data.
Perform calibration procedure every 4s
Signed-off-by: Lorenzo Bianconi <[email protected]>
Use mt76_poll_msec utility routine for CORE_R34 register polling
instead of mt76_poll in order to allow the hw to complete requested
calibration since on slow devices (e.g. mt7620 based boards) calibration
takes longer than 2ms
Fixes: 66a34c66e0cb ("mt76x0: phy: add phy/vco temperature compensation")
Signed-off-by: Lorenzo Bianconi <[email protected]>
MT_BBP(AGC, 8) register has values depend on band in
mt76x0_bbp_switch_tab, so we should not overwrite other fields
than MT_BBP_AGC_GAIN when setting gain.
This can fix performance issues when connecting to 2.4GHz AP.
Fixes: 4636a2544c3b ("mt76x0: phy: align channel gain logic to mt76x2 one")
Acked-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
We use always 1 as band parameter for MCU_CAL_LC, this break 2GHz,
we should use 0 for this band instead.
Patch fixes problems happened sometimes when try to associate with 2GHz
AP and manifest by errors like below:
[14680.920823] wlan0: authenticate with 18:31:bf:c0:51:b0
[14681.109506] wlan0: send auth to 18:31:bf:c0:51:b0 (try 1/3)
[14681.310454] wlan0: send auth to 18:31:bf:c0:51:b0 (try 2/3)
[14681.518469] wlan0: send auth to 18:31:bf:c0:51:b0 (try 3/3)
[14681.726499] wlan0: authentication with 18:31:bf:c0:51:b0 timed out
Fixes: 9aec146d0f6b ("mt76x0: pci: introduce mt76x0_phy_calirate routine")
Signed-off-by: Stanislaw Gruszka <[email protected]>
Introduce dfs support in mt76x0e driver and unlock radar channels
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Update mt76x0_phy_ant_select() to conform vendor driver, most notably
add dual antenna mode support, read configuration from EEPROM and
move ant select out of channel config to init phase. Plus small MT7630E
quirk for MT_CMB_CTRL register which vendor driver dedicated to this
chip do.
This make MT7630E workable with mt76x0e driver and do not cause any
problems on MT7610U for me.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Add submit_urb and rx_urb static tracepoints in mt76-usb module.
Move trace_mac_txstat_fetch in mt76x02_mac_load_tx_status routine
in order to be available to usb drivers. Moreover remove
no longer used mt76x0/trace.{c,h}
Signed-off-by: Lorenzo Bianconi <[email protected]>
Some RF registers need different values for various chips.
For at least mt76x0_rf_central_tab registers, overwriting them later does
not work, as the wrong values can cause the entire system to hang on some
devices with MT7610E
Signed-off-by: Felix Fietkau <[email protected]>
Driver works better for MT7630 without MCU calibration, which
looks like it can hangs the firmware. Vendor driver do not
perform it for MT7630 as well.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Align phy calibration logic between mt76x0u and mt76x0e drivers
This patch improves connection stability with low SNR
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Simplify mt76x0_phy_vco_cal and mt76x0_phy_set_chan_rf_params
routines using mt76x0_rf_wr, mt76x0_rf_set and mt76x0_rf_clear
helper routines. Moreover over get rid of magic numbers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use mt76x0_phy as prefix for routines in mt76x0/phy.c
Moreover use mt76x0_rf_set to enable vco calibration in
mt76x0_phy_vco_cal
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Do not perform phy/vga calibration during channel switch.
Moreover remove mt76x0_agc_save and mt76x0_agc_restore routines
since they are no longer necessary. Furthermore run mt76_set_channel
in order to check if there are pending frames during channel switch
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Update vga tuning algorithm to the one used in mt76x2 driver
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce phy/vco temperature calibration.
Moreover fix configuration of register 67 on bank0
during temperature reading and use mt76_poll utility routine
to poll core34 register.
Furthermore temperature compensation needs to be disabled
if the device supports tssi compensation.
This issue has never been hit since temperature reading is not
actually used by usb code.
Fixes: 10de7a8b4ab9 ("mt76x0: phy files")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Do not run mt76x0_vco_cal and mt76x0_bbp_set_bw routines and
configure MT_TX_SW_CFG0 register for pcie devices in
mt76x0_phy_set_channel function.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add mt76x0_phy_calirate routine in order to perform
phy calibration for mt76x0e devices.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rename mt76x0_phy_calibrate routine in mt76x0_phy_calibration_work
in order to not collide with calibration routine for mt76x0e
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76x02_phy_set_band routine in mt76x02_phy.c since
it is shared between mt76x0 and mt76x2 drivers and remove
duplicated code
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76x02_phy_set_bw routine in mt76x02_phy.c since
it is shared between mt76x0 and mt76x2 drivers and remove
duplicated code
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use mt76x02_dev data structure as reference in mt76x02_eeprom.c
instead of mt76_dev
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use mt76x02_dev data structure as reference in mt76x02_phy.c
instead of mt76_dev
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use mt76x02_dev data structure as reference in mt76x02_mcu.c
instead of mt76_dev
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix typo in bank check in mt76x0_rf_csr_{wr,rr} routines.
This issue has never been hit since mt76x0_rf_csr_{wr,rr}
are actually used just by pci code
Fixes: 10de7a8b4ab9 ("mt76x0: phy files")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use mt76_is_usb() to identify RF access method instead of
MT76_STATE_MCU_RUNNING flag and add warning since MCU has
to be initialized before we can access RF registers via MCU.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
PCIe version don't use MCU for RF registers access. We need
to correct RF CSR method to support up to 127 RF registers.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Unify rxwi parsing between mt76x2 and mt76x0. Remove the following
routines:
- mt76x0_phy_get_rssi
- mt76x0_queue_rx_skb
- mt76x0_mac_process_rx
Moreover remove mt76x2/common.c and mt76x0/mac.h since are empty files
Enable CCMP PN sw validation
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Merge mt76x0_dev data structure in mt76x02_dev one and remove
duplicated code. Remove unused definition in mt76x0.h.
Moreover merge mt76x0_caldata and mt76x02_rx_freq_cal data structures.
This is a preliminary patch for rxwi unification.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove hw_atomic_mutex mutex in mt76x0_dev data structure
since mt76x0_phy_set_channel is already protected by mt76_dev
mutex while mt76x0_chip_onoff is used just at device probe or
cleanup
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use shared mt76x02 utility routines for rssi tracking.
Moreover remove no longer used con_mon_lock spinlock
and following variable:
- ap_bssid
- bcn_freq_off
- bcn_phy_mode
- avg_rssi
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76x02_phy_set_rxpath and mt76x02_phy_tx_dac routines in
mt76x02_phy.c since they are shared between mt76x2 and mt76x0 drivers.
Moreover move chainmask variable from mt76x2/mt76x0 to mt76_dev data
structure
Signed-off-by: Lorenzo Bianconi <[email protected]>
Move mt76x0_ant_select routine in __mt76x0_phy_set_channel in order to
configure antenna parameters according to the current wireless channel
Signed-off-by: Lorenzo Bianconi <[email protected]>
Add mt76x0_phy_set_txpower routine in order to configure
base and per rate tx power gain. Moreover take into account
txpower_conf in order to limit the tx power gain according to
the bound provided by mac80211
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In order to unify eeprom parsing between mt76x0 and mt76x2 drivers,
remove eeprom pointer dependency from mt76x0_get_power_info routine.
Remove mt76x0_eeprom_params since it is now an empty structure
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In order to unify eeprom parsing between mt76x0 and mt76x2 drivers,
remove eeprom pointer dependency from mt76x0_set_tx_power_per_rate.
Moreover use mt76_rate_power to store power vs rate calibration data.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove mt76x0_extra_power_over_mac and mt76x0_phy_set_tx_power routines
since they are not actually used and tx power handling will be unified
with mt76x2 driver
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Unify frequency offset parsing with mt76x2 driver using
eeprom utility routines available in mt76x02-lib module
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Unify temperature offset parsing with mt76x2 driver using
eeprom utility routines available in mt76x02-lib module
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Unify rssi_offset parsing with mt76x2 driver using eeprom utility
routines available in mt76x02-lib module
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Unify lna gain parsing with mt76x2 driver using eeprom utility
routines available in mt76x02-lib module
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76x2_ext_pa_enabled utility routine in mt76x02_eeprom.c
and remove duplicated code. This is a preliminary patch to
unify eeprom code between mt76x2 and mt76x0 driver
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mcu_calibrate routine in mt76x02-lib module since it is
shared between USB and PCI code. Moreover remove duplicated
code
Signed-off-by: Lorenzo Bianconi <[email protected]>
Use mcu common helpers instead of usb specific routines.
Add static qualifier to the following functions:
- mt76u_mcu_msg_alloc
- __mt76u_mcu_send_msg
- mt76u_mcu_send_msg
- mt76u_mcu_wr_rp
- mt76u_mcu_rd_rp
- mt76u_wr_rp
- mt76u_rd_rp
This is a preliminary patch to move mt76x02 usb mcu code in
mt76x02-usb module
Acked-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Add USB implementation for read and write reg pair routines.
The actual implementation can use mcu related routines according to
MCU state
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
According to vendor sdk, vco calibration has to be executed
for each channel configuration whereas mcu calibration has to be
performed during channel scanning. This patch fixes the mt76x0
monitor mode issue since in that configuration vco calibration
was never executed
Fixes: 10de7a8b4ab9 ("mt76x0: phy files")
Tested-by: Sid Hayn <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
