mt76 runs its own beacon monitor. mt76_beacon_mon_check() counts a miss
for each affiliated link of an MLD, and it stops the count while the phy
is off channel. mt7996 supplies it through mt76_rx_beacon(), but it does
not set CONNECTION_MONITOR. Therefore mac80211 also starts its legacy
monitor.
The legacy monitor knows one interface, not a set of links. It also
counts while the radio serves a different link. After seven beacon
intervals it removes an association that still carries traffic on the
other links.
Set the CONNECTION_MONITOR flag to disable the legacy monitor.
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
When receiving a 4 address non-AMSDU packet, there is no bssid in the
address fields, which breaks powersave handling for 4-address peers.
Set the mcu command to use A1 as bssid when receiving 4 address
non-AMSDU packets on mt7992 and mt7990.
Also skip mt7996_mac_init_band() for invalid bands, so the command is
only sent for bands that actually exist on the device.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Both drivers cancelled dump_work on unregister but left reset_work and
rc_work to be flushed only by destroy_workqueue() in mt76_free_device(),
which runs after the hw is unregistered and the hardware stopped. A
reset_work that fires in that window calls ieee80211_restart_hw() and
re-arms mac_work on an unregistered hw, and rc_work touches station state
being torn down. Cancel both up front, alongside dump_work.
Fixes: e57b7901469f ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets")
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Felix Fietkau <[email protected]>
According to the definition in IEEE Std 802.11be-2024, Table 9-417r:
- If 80 MHz is not supported, bit 1-3 are set to 0.
- If 160 MHz is not supported, bit 2-3 are set to 0.
- If 320 MHz is not supported, bit 3 is set to 0.
Fixes: 348533eb968d ("wifi: mt76: mt7996: add EHT capability init")
Signed-off-by: Shayne Chen <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
mt7996/mt7992 are single-wiphy, multi-band devices. The driver assigns
each band its own MAC address from a per-band EEPROM entry, or derives
it from the primary band's address when that entry is empty, however
only the primary band's is published as perm_addr. The per-band
addresses are not exposed to cfg80211, so consumers usually fall back
to deriving one from perm_addr.
Store each band's address in wiphy->addresses[], indexed by radio, so
cfg80211 exposes the address the hardware actually uses for that radio.
addresses[0] is the primary band and matches perm_addr, as cfg80211
requires.
Link: https://github.com/openwrt/openwrt/issues/23578
Tested-on: Gemtek W1700K (MT7996)
Signed-off-by: Kenneth Kasilag <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Add hardware airtime fairness (ATF) support for mt7996, using the MAC's
weighted DWRR scheduler (VoW) to balance TX airtime between stations, in
the same way as the mt7915 implementation.
This supplements mac80211's software airtime fairness rather than
replacing it: software ATF keeps scheduling the host TX queues, while the
hardware scheduler enforces fairness on the offloaded path where the host
has no airtime accounting, such as when WED is active.
A station's TX airtime weight is taken from mac80211 through the
sta_set_airtime_weight op and applied to the hardware scheduler directly;
the per-AC DWRR quantum levels and the station's BSS group index are
derived on the fly, mapping the weight logarithmically onto the global
hardware quantum table. ATF and WATF are enabled by default and can be
toggled together at runtime through the "vow_atf" debugfs file.
Signed-off-by: Benjamin Lin <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Skip WFSYS reset during bootup for MT7990 chipsets; only reset if L0.5
recovery is triggered.
Without this fix, the following kernel error may occur:
Internal error: synchronous external abort.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
When the mt7996 pci chip is detaching, the mt7996_crash_data is
released in mt7996_coredump_unregister(). However, the work item
dump_work may still be running or pending, leading to UAF bugs
when the already freed crash_data is dereferenced again in
mt7996_mac_dump_work().
The race condition can occur as follows:
CPU 0 (removal path) | CPU 1 (workqueue)
mt7996_pci_remove() | mt7996_sys_recovery_set()
mt7996_unregister_device() | mt7996_reset()
mt7996_coredump_unregister() | queue_work()
vfree(dev->coredump.crash_data) | mt7996_mac_dump_work()
| crash_data-> // UAF
Fix this by ensuring dump_work is properly canceled before
the crash_data is deallocated. Add cancel_work_sync() in
mt7996_unregister_device() to synchronize with any pending
or executing dump work.
Fixes: 878161d5d4a4 ("wifi: mt76: mt7996: enable coredump support")
Signed-off-by: Duoming Zhou <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
MT7992 and MT7990 support up to 19 interfaces per band and 32 in total.
Fixes: 8df63a4bbe3d ("wifi: mt76: mt7996: adjust interface num and wtbl size for mt7992")
Signed-off-by: Shayne Chen <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Introduce Airoha NPU support to MT7996 driver. NPU is used to enable
traffic forward offloading between the MT76 NIC and the Airoha ethernet one
available on the Airoha EN7581 SoC using Netfilter Flowtable APIs.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
MediaTek has asked to switch from the ISC license to BSD-3-Clause-Clear,
in order to improve clarity and the legal integrity of the code.
The BSD-3-Clause license includes the "no endorsement" clause, which is
important for protecting the reputation of the original authors and
contributors by preventing unauthorized use of their names for endorsement
purposes.
This clause is absent in the BSD-2-Clause license, which is more permissive
but lacks this specific protection.
This change also cleans up the license of some Kconfig/Makefile files,
which were accidentally marked as GPL.
The GPL 2.0 remains in use on mt76x0, as well as two source files in mt7615
for which the license situation still needs to be clarified.
Signed-off-by: Felix Fietkau <[email protected]>
mt76_eeprom_override has of_get_mac_address, which can return
-EPROBE_DEFER if the nvmem driver gets loaded after mt76 for some
reason.
Make sure this gets passed to probe so that nvmem mac overrides always
work.
Signed-off-by: Rosen Penev <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Set MT_WF_RFCR_DROP_OTHER_UC by default and disable this flag in
mt7996_set_monitor only if monitor mode is enabled.
Without this patch, the MT_WF_RFCR_DROP_OTHER_UC would not be set so the
driver would receive lots of packets meant for other devices.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce rx_rro_ind_process and rx_rro_add_msdu_page callbacks and the
related logic in the MT7996 driver. This is a preliminary patch to
decouple RRO logic from WED support and reuse RRO when WED module is not
available.
Signed-off-by: Rex Lu <[email protected]>
Co-developed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
One variant of MT7992 has 5 TX paths, so extend the power delta function
to support it. Also, rename nss_delta to path_delta since the value is
based on the number of TX paths rather tha the number of spatial streams.
(path delta [0.5 dBm] = 10 * log(path number) [dBm] * 2)
Co-developed-by: StanleyYP Wang <[email protected]>
Signed-off-by: StanleyYP Wang <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Set the max AMPDU length in the EHT MAC CAP. Without this patch, the
peer station cannot obtain the correct capability, which prevents
achieving peak throughput on the 2 GHz band.
Fixes: 1816ad9381e0 ("wifi: mt76: mt7996: add max mpdu len capability")
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Fix the beamformee SS field for the mt7996, mt7992 and mt7990 chipsets.
For the mt7992, this value shall be set to 0x4, while the others shall
be set to 0x3.
Fixes: 5b20557593d4 ("wifi: mt76: connac: adjust phy capabilities based on band constraints")
Signed-off-by: Howard Hsu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
devm_kasprintf() can return a NULL pointer on failure,but this
returned value in mt7996_thermal_init() is not checked.
Add NULL check in mt7996_thermal_init(), to handle kernel NULL
pointer dereference error.
Fixes: 69d54ce7491d ("wifi: mt76: mt7996: switch to single multi-radio wiphy")
Signed-off-by: Charles Han <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
The chipset name (i.e., brand name) used by the driver may cause confusion
with the PCI device ID when adding support for new chipsets.
| Chipset name | PCI device id |
|--------------|----------------|
| 7996 | 0x7990, 0x7991 |
| 7992 | 0x7992, 0x799a |
| 7990 | 0x7993, 0x799b |
To prevent confusion, replace the code that directly uses the device ID
with macros. This is a preliminary patch to support mt7990 chipset.
Co-developed-by: Peter Chiu <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Set HE SU PPDU And HE MU PPDU With 4x HE-LTF And 0.8 us GI within HE PHY
Capabilities element as 1 since hardware can support.
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Howard Hsu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
This commit includes two changes. First, enable "EHT MU PPDU With 4x
EHT-LTF And 0.8us GI" in EHT Phy capabilities element since hardware
can support. Second, fix the value of "Maximum number of supported
EHT LTFs" in the same element, where the previous setting of 3 in
Bit 3-4 was incorrect.
Fixes: 348533eb968d ("wifi: mt76: mt7996: add EHT capability init")
Signed-off-by: Howard Hsu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Set max mpdu len to 11454 according to hardware capability.
Without this patch, the max ampdu length would be 3895 and count not get
expected performance.
Fixes: 348533eb968d ("wifi: mt76: mt7996: add EHT capability init")
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
