Set mpdu density to 2 usec for non-mt7915 Wi-Fi 6 generation chipsets
to align to the hardware capability which improves the throughput.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The IEEE80211_VHT_CAP_EXT_NSS_BW value already indicates support for half-NSS
160 MHz support, so it is wrong to also advertise full 160 MHz support.
Fixes: c2f73eacee3b ("wifi: mt76: mt7915: add back 160MHz channel width support for MT7915")
Signed-off-by: Felix Fietkau <[email protected]>
Move the following routines in mt76-connac lib since they are shared
between mt7915 and mt7921:
- mt76_connac2_tx_check_aggr
- mt76_connac2_txwi_free
- mt76_connac2_tx_token_put
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
sta_poll_list and sta_poll_lock are used by most of the drivers, so move
them in mt76_dev structure.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Concurrent binding/non-binding skbs could be handled anywhere which leads
to mixed byte counting, so switch to use PPDU TxS reporting regardless Tx
paths when WED is active.
Fixes: 43eaa3689507 ("wifi: mt76: add PPDU based TxS support for WED device")
Co-developed-by: Ryder Lee <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Get missing tx retries/failed counts from txfree done events and report
them via mt7915_sta_statistics().
Co-developed-by: Peter Chiu <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add support for the MediaTek MT7981 SoC which is similar to the MT7986
but with a newer IP cores and only 2x ARM Cortex-A53 instead of 4x.
Unlike MT7986 the MT7981 can only connect a single wireless frontend,
usually MT7976 is used for DBDC.
Signed-off-by: Alexander Couzens <[email protected]>
Signed-off-by: Daniel Golle <[email protected]>
gen_ppe_thresh routine is shared between mt7615, mt7915, mt7921 and
mt7996 so move it in mt76_connac module.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
irq_tasklet struct is used by most of the drivers (e.g. mt7915, mt7921,
mt7615, mt7663 and mt7996) so move it in common code.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
A number of users reported that this support was working fine before
it got removed. Add it back, but leave out the unsupported 80+80 mode.
Fixes: ac922bd60ace ("wifi: mt76: mt7915: remove BW160 and BW80+80 support")
Signed-off-by: Felix Fietkau <[email protected]>
If kernel do not enable CONFIG_HWMON, it may cause thermal
initialization to be done with temperature value 0 and then can not
transmit. This commit fixes it by setting trigger/restore temperature
before checking CONFIG_HWMON.
Fixes: 7d12b38ab6f6 ("wifi: mt76: mt7915: call mt7915_mcu_set_thermal_throttling() only after init_work")
Signed-off-by: Howard Hsu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Drop the lock before returning -EINVAL.
Fixes: ecaccdae7a7e ("wifi: mt76: mt7915: rework mt7915_thermal_temp_store()")
Signed-off-by: Dan Carpenter <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Call mt7915_mcu_set_thermal_protect() through
mt7915_thermal_temp_store() to update firmware trigger/restore temp
directly.
Fixes: 02ee68b95d81 ("mt76: mt7915: add control knobs for thermal throttling")
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Howard Hsu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This patch includes 2 changes:
1. Firmware expects to disable thermal protect first before
reconfiguring.
2. Separate setting thermal_protect and setting thermal_tx_duty into
different functions. These two firmware commands do not need to send
together.
Fixes: 34b877d972be ("mt76: mt7915: add thermal cooling device support")
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Howard Hsu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Enable thermal management by default shall not be executed during mcu
init. This causes thermal configuration being reset to the firmware
default settings.
Fixes: 0063b86c9120 ("mt76: mt7915e: Enable thermal management by default")
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Howard Hsu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce the capability to support per-phy led blinking. This is needed
for devices supporting dbdc.
Tested-by: Frank Wunderlich <[email protected]>
Co-developed-by: Ryder Lee <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move leds struct in mt76_phy in order to have leds associated to phy
(e.g. in dbdc mode) instead of per device.
Tested-by: Frank Wunderlich <[email protected]>
Co-developed-by: Ryder Lee <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The commit dc44c45c8cd0 added band_idx into mt76_phy, so switching to
rely on that.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This adds support for adjusting the Txpower level while pushing
traffic to an associated station. The allowed range is from 0 to
the maximum power of channel.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The hardware simply does not support this in DBDC mode. Remove it from
the HE capabilities.
Signed-off-by: Nicolas Cavallari <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Do not hardcode beamformee 4 space-time streams support, because
DBDC can only support up to 2.
Fixes: 00b2e16e0063 ("mt76: mt7915: add TxBF capabilities")
Signed-off-by: Nicolas Cavallari <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Host triggered and catastrophic event triggered firmware core dumping
for basic firmware issues triage, including state reporting, task/irq
info, function calltrace and MCU memory dump.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add mt7915_reset() and refactor mt7915_mac_reset_work() to support
full system recovery.
Co-developed-by: Ryder Lee <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This reports signal strength of ACK packets from the peer as measured
at each interface.
Tested-by: Shurong Wen <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The MIB INFO command is fetching MIB_BUSY_TIME, MIB_TX_TIME, MIB_RX_TIME and
MIB_OBSS_AIRTIME from the radio and filling out cc_busy, cc_tx, cc_bss_rx
and cc_rx respectively.
busy should be >= tx + rx >= tx + bss_rx but we don’t always quite see this.
Sometimes tx + rx is a bit higher than busy due to inaccurate accounting,
so this patch recalculates numbers to make them more reasonable.
Reported-By: Kevin Schneider <[email protected]>
Tested-by: Kevin Schneider <[email protected]>
Tested-by: Chad Monroe <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
A variant of mt7916 supports up to 3 tx/rx paths but with only
2 spatial streams. An example usage of the 3rd path is to server as
an auxiliary for beamforming.
In order to deal with this case, this patch reworks some parts to
correctly use paths or streams.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce phys array in mt76_dev structure to reference mt76_phy
supported by the chipset. This is a preliminary patch to introduce
newer chipset support.
Signed-off-by: Lorenzo Bianconi <[email protected]>
After initially establishing a connection, it can produce multi-second latency
spikes and tx hangs when pushing traffic.
It should work better for MT7916 and MT7986, so leave it enabled there
Signed-off-by: Felix Fietkau <[email protected]>
According IEEE Std 802.11-2020, its definition is:
Indicates whether the STA is capable of interpreting the Extended NSS BW
Support subfield of the VHT Capabilities Information field.
Some APs, such as Xiaomi AX6000, would check this one for BW settings.
mt76 driver can get max BW capability only if the this field is confgured
properly.
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Ming Yen Hsieh <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This patch disables RX_TRANS_SHORT to make MDP to do header translation
when payload less than 8 bytes, hence the (QoS) null data can be encapsulated
to 802.3 format. However, WDS requires (QoS) null data in 802.11 format
to created vlan AP interfaces.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: lian.chen <[email protected]>
Signed-off-by: Sujuan Chen <[email protected]>
Signed-off-by: Bo Jiao <[email protected]>
Don't populate the read-only array ppet16_ppet8_ru3_ru0 on the stack but
instead make it static const. Also makes the object code a little smaller.
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
Signed-off-by: Colin Ian King <[email protected]>
Soft reboot might not clear certain condition, so always call
mt7915_wfsys_reset() during init.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Clean up and fix error paths in mt7915_register_device
Initialize second DBDC tx queue in mt7915_dma_init
Signed-off-by: Felix Fietkau <[email protected]>
Various spelling mistakes in comments.
Detected with the help of Coccinelle.
Signed-off-by: Julia Lawall <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This patch fixes performance issue of beamforming tx on
bandwidth 160MHz.
Fixes: 99ad32a4ca3a ("mt76: mt7915: add support for MT7986")
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
