Introduce rx_check callback support for mt7663s driver.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Similar to mt7921 driver, introduce mt7615_mutex_acquire/release in
mt7615_sta_set_decap_offload in order to avoid sending mcu commands
while the device is in low-power state.
Fixes: d4b98c63d7a77 ("mt76: mt7615: add support for rx decapsulation offload")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce rx_check callback support for mt7663u and mt7921u drivers.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The code was accidentally shifting register values down by tid % 32 instead of
(tid * field_size) % 32.
Signed-off-by: Felix Fietkau <[email protected]>
Report phy_indx in tx_info->hw_queue. This is a preliminary patch to add
newer chipset support
Co-developed-by: Bo Jiao <[email protected]>
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Introduce phy_idx to mt76_wcid structure instead of ext_phy.
This is a preliminary patch to add newer chipset support.
Co-developed-by: Bo Jiao <[email protected]>
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Introduce phys array in mt76_dev structure to reference mt76_phy
supported by the chipset. This is a preliminary patch to introduce
newer chipset support.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Introduce phy_idx mt76_rx_status instead of ext_idx. This is a
preliminary patch to add newer chipset support
Co-developed-by: Bo Jiao <[email protected]>
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Move mt76_connac_init_tx_queues and mt76_connac_tx_cleanup routines
in mt76_connac module. This is a preliminary patch to add mt7990
chipset support.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Previously the code used skb_set_queue_mapping for management or non-bufferable
powersave frames that need to be sent to a different hardware queue.
This can confuse AQL, which expects the value to remain the same until the tx
status report.
The only place that currently uses the altered skb queue mapping is the txwi
write function. Change the code to pass the hardware queue id as a function
parameter instead.
Signed-off-by: Felix Fietkau <[email protected]>
For some reason, mt7615 reacts badly to repeatedly enabling/disabling the radar
detector without also switching the channel.
This results in very bad throughput on DFS channels, because
hw->conf.radar_enabled can get toggled a few times after CAC ends.
Fix this by always leaving the DFS detector enabled on DFS channels and instead
suppress unwanted detection events.
Fixes: 2c86f6752046 ("mt76: mt7615: fix/rewrite the dfs state handling logic")
Signed-off-by: Felix Fietkau <[email protected]>
Set EXTRA_INFO_NEW for the first time only to prevent adding the same
starec entry, otherwise the entry might be removed in fw.
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76_connac2_mcu_fill_message routine in shared module in order to
reuse it for mt7921 and mt7915e drivers. This is a preliminary patch to
add mt7990 driver support.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt7615_txp_skb_unmap in shared code and reuse it in mt7915e and
mt7921e driver.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Now we can move mt76_connac_write_hw_txp routine in mt76-connac module
and reuse it in mt7921e and mt7615e driver.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Since now txp structures are in common code we can reuse
mt76_connac_tx_complete_skb routine in mt7921e, mt7915e and mt7615e
drivers.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76_connac_tx_free structure in mt76_connac module since it is
shared by mt7615 and mt7921 drivers.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Since mt7615_txp_ptr is shared between mt7615 and mt7921 move it in
mt76_connac module.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Since mt76_connac_fw_txp struct is shared between mt7615e, mt7915e and
mt7921e, move it in mt76_connac module.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Do not update pm stats if mt7615_mcu_fw_pmctrl returns an error.
Fixes: abe912ae3cd42 ("mt76: mt7663: add awake and doze time accounting")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
According IEEE Std 802.11-2020, its definition is:
Indicates whether the STA is capable of interpreting the Extended NSS BW
Support subfield of the VHT Capabilities Information field.
Some APs, such as Xiaomi AX6000, would check this one for BW settings.
mt76 driver can get max BW capability only if the this field is confgured
properly.
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Ming Yen Hsieh <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
napi_schedule() can call __raise_softirq_irqoff(), which can perform softirq
handling, so it must not be called in a pure process context with BH enabled.
Signed-off-by: Felix Fietkau <[email protected]>
MT7915_MAX_INTERFACES is per-band declaration in MT7915/MT7986/MT7916.
Enlarge vif_mask to 64 bits wide, including the bit operation.
Reviewed-by: Shayne Chen <[email protected]>
Signed-off-by: Evelyn Tsai <[email protected]>
Signed-off-by: Bo Jiao <[email protected]>
When setup monitor mode in DFS channel, mt76 send CH_SWITCH_DFS to
fw for channel config. This would cause rx performance bad while
monitoring frames. Settings CH_SWITCH_NORMAL in monitor mode would
get the same performance as normal channels.
Reviewed-by: Shayne Chen <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce __mt76u_init unitility routine and move mt7615 usb bus ops
into mt7615 module in order to allow specifying driver specific
parameter.
This is a preliminary patch to add usb support to mt7921 driver.
Tested-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Switch to use le32/16_get_bits() to simplfy codes and specify
the size explicitly to avoid potential issues.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The original single LDPC cap bit cannot be used to
differentiate LDPC cap in each PHY mode.
This modification split the single bit into 3 bits,
ht_ldpc, vht_ldpc, and he_ldpc.
Reviewed-by: Ryder Lee <[email protected]>
Suggested-by: Money Wang <[email protected]>
Signed-off-by: MeiChia Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt7663u_mcu_power_on utility routine since the code is shared
between mt7663u_mcu_init() and mt7663u_probe().
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Check return value of mt7615_mcu_restart routine in mt7663u_mcu_init().
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When operating on a mix of DFS and non-DFS channels, the driver only checks
the CAC status of the control channel. This causes beacons/tx to fail if the
control channel is on a non-DFS channel.
Fix this by calling cfg80211_reg_can_beacon to determine the DFS status of
all affected channels
Signed-off-by: Felix Fietkau <[email protected]>
The following error is see from the compiler:
mt7615/debugfs.c: In function ‘mt7615_ext_mac_addr_read’:
mt7615/debugfs.c:465:1: warning: the frame size of 1072 bytes is
larger than 1024 bytes [-Wframe-larger-than=]
The issue is due to allocating a buffer as string storage.
Fix by converting to a dynamical allocation of the buffer.
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add SAR spec support to mt7615 driver to allow configuring SAR power
limitations on the frequency ranges from the userland.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Instead of just taking the maximum per-chain signal strength values,
add an approximation for the sum of the combined signal.
This should more accurately reflect the real signal strength, especially
if the per-chain signal strength values are close to each other
Signed-off-by: Felix Fietkau <[email protected]>
Do not always copy ethernet header in mt{7615,7915,7921}_reverse_frag0_hdr_trans
and use a pointer instead.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
We don't have to create a separate sdio.xmit_buf buffer for each queue.
Instead, we just need to create one, reuse it across all queues to reduce
memory consumption further.
And then we should take it into account the actual the host and the device
MMC capability to determine what the appropriate xmit_buf_size can be.
Both MT7921S and MT7663 can support up to Tx FIFO size of 0x3fe00 which
means the device can receive 511 blocks of block size 512 in a row from
the host. So if the driver aggregates the frames as many as possible the
the device can support, we can merge multiple MMC requests into a single
one to get rid of the overhead of the handling and synchronizing in those
unnecessary MMC requests and reduce the SDIO lock contention with the
Bluetooth concurrent traffic and finally to have the higher bus
utilization with less idle cycle.
With the patch, it is helpful for WiFi to have steady throughput
performance especially while running Bluetooth concurrently.
Co-developed-by: Deren Wu <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The radar detctor is used for dfs channel. So it will start after switching
to dfs channel and will stop after leaving. The TX will be blocked if radar
detctor isn't stopped in non-dfs channel.
This patch resets the dfs state to indicate the radar detector needs to be
stopped.
Signed-off-by: Xing Song <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Check sta_rates pointer value in mt7615_sta_rate_tbl_update routine
since minstrel_ht_update_rates can fail allocating rates array.
Fixes: 04b8e65922f63 ("mt76: add mac80211 driver for MT7615 PCIe-based chipsets")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix a possible race in mt7615_pm_power_save_work() if rx/tx napi
schedules ps_work and we are currently accessing device register
on a different cpu.
Fixes: db928f1ab9789 ("mt76: mt7663: rely on mt76_connac_pm_ref/mt76_connac_pm_unref in tx/rx napi")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Similar to mt7915 driver, process txfree and txstatus without allocating
skbs in order to reduce pressure on the memory allocator
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In some cases, the WA firmware needs to know if encryption is used, in order
to set the protection bit of packets
Signed-off-by: Felix Fietkau <[email protected]>
