ED/CCA Tx blocking checks need to be run every 100 ms in order to avoid
triggering too late and keeping tx blocking on for too long
Signed-off-by: Felix Fietkau <[email protected]>
Add mt76x0_init_txpower in order to initialize max_power per channel
at device bootstrap. Modify mt76x0_get_tx_power_per_rate and
mt76x0_get_power_info signature in order to compute tx power for
non-operating channels
Signed-off-by: Lorenzo Bianconi <[email protected]>
Initialize target_power variable in mt76x0_phy_set_txpower in order to
report target_power in debugfs
Signed-off-by: Lorenzo Bianconi <[email protected]>
Ported from the reference driver. Should fix compliance with ETSI
regulatories on preventing transmission while energy detect values
are above the threshold.
The code has been tested using an ath9k device running tx99 as
noise generator
Signed-off-by: Lorenzo Bianconi <[email protected]>
MODULE_FIRMWARE() is used in usb_mcu.c and provided by linux/module.h,
but this header file is not directly included. This causes problems in
backports with some kernel versions.
Add the missing include.
Signed-off-by: Hauke Mehrtens <[email protected]>
We always wait for CMD_CALIBRATION_OP mcu message, but wait argument is used
for do additional MT_MCU_COM_REG0 register operations, which are needed
for mt76x2e devices and we can use appropriate check instead of wait argument.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Add mt76x02_config_mac_addr_list routine in order to set
the mac address list supported by the driver. Initialize
wiphy->addresses/n_addresses for mt76x0e driver
Signed-off-by: Lorenzo Bianconi <[email protected]>
Assure that after we initialize dev->cal.low_gain to -1 this
will cause update gain calibration. Otherwise this might or
might not happen depending on value of second bit of low_gain
and values read from registers in mt76x02_phy_adjust_vga_gain().
Signed-off-by: Stanislaw Gruszka <[email protected]>
If we are associated and scanning is performed, sw_scan_complete callback
is done after we get back to operating channel, so we do not perform
queue cal work. Fix this queue cal work from sw_scan_complete().
On mt76x0 we have to restore gain in MT_BBP(AGC, 8) register after
scanning, as it was multiple times modified by channel switch code.
So queue cal work without any delay to set AGC gain value.
Similar like in mt76x2 init AGC gain only when set operating channel
and just check before queuing cal work in sw_scan_complete() if
initialization was already done.
Fixes: bbd10586f0df ("mt76x0: phy: do not run calibration during channel switch")
Signed-off-by: Stanislaw Gruszka <[email protected]>
Remove wait argument from mt76x02_mcu_function_select and wait for
response when function is not Q_SELECT, what is the same behaviour
like in vendor driver.
Note this change behaviour for PCIe devices for Q_SELECT function
form wait to no-wait, and for mt76x0u BW_SETTING from no-wait to wait.
But the change is in align with vendor driver.
Signed-off-by: Stanislaw Gruszka <[email protected]>
We almost always use patter like this:
skb = mt76_mcu_msg_alloc(dev, &msg, sizeof(msg));
return mt76_mcu_send_msg(dev, skb, CMD_FUN_SET_OP, wait_resp);
This is not needed, we can allocate skb in mcu_send_msg routine.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Run mt76x0 tssi calibration process if enabled in eeprom data.
Perform calibration procedure every 4s
Signed-off-by: Lorenzo Bianconi <[email protected]>
Use mt76x02_mac_wcid_setup utility routine for wcid init configuration
and remove duplicated code. This patch fixes a mt76x0 AP issue since
hw key table selection was set to pairwise by default
Fixes: dbad2adcb2c7 ("mt76x0: pci: enable AP support")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Use mt76x02_mac_shared_key_setup utility routine for shared key
initialization and remove duplicated code
Signed-off-by: Lorenzo Bianconi <[email protected]>
Use mt76_poll_msec utility routine for CORE_R34 register polling
instead of mt76_poll in order to allow the hw to complete requested
calibration since on slow devices (e.g. mt7620 based boards) calibration
takes longer than 2ms
Fixes: 66a34c66e0cb ("mt76x0: phy: add phy/vco temperature compensation")
Signed-off-by: Lorenzo Bianconi <[email protected]>
MT_BBP(AGC, 8) register has values depend on band in
mt76x0_bbp_switch_tab, so we should not overwrite other fields
than MT_BBP_AGC_GAIN when setting gain.
This can fix performance issues when connecting to 2.4GHz AP.
Fixes: 4636a2544c3b ("mt76x0: phy: align channel gain logic to mt76x2 one")
Acked-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
We use always 1 as band parameter for MCU_CAL_LC, this break 2GHz,
we should use 0 for this band instead.
Patch fixes problems happened sometimes when try to associate with 2GHz
AP and manifest by errors like below:
[14680.920823] wlan0: authenticate with 18:31:bf:c0:51:b0
[14681.109506] wlan0: send auth to 18:31:bf:c0:51:b0 (try 1/3)
[14681.310454] wlan0: send auth to 18:31:bf:c0:51:b0 (try 2/3)
[14681.518469] wlan0: send auth to 18:31:bf:c0:51:b0 (try 3/3)
[14681.726499] wlan0: authentication with 18:31:bf:c0:51:b0 timed out
Fixes: 9aec146d0f6b ("mt76x0: pci: introduce mt76x0_phy_calirate routine")
Signed-off-by: Stanislaw Gruszka <[email protected]>
Introduce dfs support in mt76x0e driver and unlock radar channels
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Unify drv_bss_info_changed mac80211 callback and remove duplicated
code in mt76x0 and mt76x2 drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76x02_set_rts_threshold and mt76x02_mac_set_tx_protection
routines in mt76x02-lib module and remove duplicated code in mt76x0
and mt76x2 drivers. Remove pci_mac.c and mt76x0/mac.c since now are
empty files
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76x02_set_tx_ackto and mt76x02_set_coverage_class routines
in mt76x02-lib module in order to be reused by mt76x0 driver.
This is a preliminary patch to unify drv_bss_info_changed mac80211
callback between mt76x0 and mt76x2 drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add missing mac80211 callbacks to mt76x0e_ops data structure
and add mt76x02_beacon utility routines in mt76x0_bss_info_changed
in order to enable/disable beacon transmission
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add mt76x02_init_beacon_config utility routine in mt76x02-lib
module in order to be reused by mt76x0 driver configuring
BSSID registers and remove duplicated code
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76x02_sta_ps utility routine in mt76x02_util.c
in order to be reused by mt76x0 driver adding AP support
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76x02_get_txpower utility routine in mt76x02-lib module
in order to be reused by mt76x0 and mt76x2u drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76x02_sw_scan and mt76x02_sw_scan_complete utility routines
in mt76x02_util.c in order to be reused by mt76x0 and mt76x2u drivers
and remove duplicated code
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Enable/disable pre_tbtt_tasklet in mt76x0 driver in order
to add AP support
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76x02_init_device routine in mt76x02_util.c in order to be
reused by mt76x0 driver and remove duplicated code. Move interface
combo definition supported by the driver in mt76x02_init_device routine
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76x02_mac_set_short_preamble routine in mt76x02-lib module
since it is shared between mt76x0 and mt76x2 drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Unify firmware version used on mt76x0e and mt76x0u drivers.
Fallback to mt7610u fw if mt7610e one is not available
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove no longer used mt76x0_mac_set_ampdu_factor routine
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Simplify mt76x0_init_mac_registers routine using mt76_set, mt76_clear
and mt76_rmw utility routines
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Update mt76x0_phy_ant_select() to conform vendor driver, most notably
add dual antenna mode support, read configuration from EEPROM and
move ant select out of channel config to init phase. Plus small MT7630E
quirk for MT_CMB_CTRL register which vendor driver dedicated to this
chip do.
This make MT7630E workable with mt76x0e driver and do not cause any
problems on MT7610U for me.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Add submit_urb and rx_urb static tracepoints in mt76-usb module.
Move trace_mac_txstat_fetch in mt76x02_mac_load_tx_status routine
in order to be available to usb drivers. Moreover remove
no longer used mt76x0/trace.{c,h}
Signed-off-by: Lorenzo Bianconi <[email protected]>
Some RF registers need different values for various chips.
For at least mt76x0_rf_central_tab registers, overwriting them later does
not work, as the wrong values can cause the entire system to hang on some
devices with MT7610E
Signed-off-by: Felix Fietkau <[email protected]>
Driver works better for MT7630 without MCU calibration, which
looks like it can hangs the firmware. Vendor driver do not
perform it for MT7630 as well.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Align phy calibration logic between mt76x0u and mt76x0e drivers
This patch improves connection stability with low SNR
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use mt76x02_mac_work utility routine as stats workqueue handler
and remove duplicated code. Moreover run mac stuck check in
mt76x02_mac_work for client interfaces.
Remove no longer used avg_ampdu_len and mt76x02_mac_stats data
structure in mt76x02_dev
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use mt76x02 debugfs implementation and remove duplicated code
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76x02_mac_work routine in mt76x02_mac.c in order to be reused by
mt76x0 driver to read device statistics
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
