status->chains was set from the antenna mask, which is derived from the
number of spatial streams, while the chain_signal array is filled from
all RCPI fields. On boards where the number of RX paths exceeds the
stream count, e.g. the 3T3R mt7916/mt7981 variant with 2 streams on the
5 GHz band, the RSSI of the extra chains was never reported.
Use the band local RX path chainmask instead.
Fixes: e57b7901469f ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets")
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
WM firmware can enter a partial failure state where RX is hung.
Detect this condition by monitoring SER_PLE_ERR_1 for MDP_RIOC_HANG_ERR
and trigger L1 SER to restore operation. Use transition detection on the
error bit to fire only once per new occurrence, preventing an infinite
SER loop when the bit remains set across checks.
Signed-off-by: Chad Monroe <[email protected]>
Suggested-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When a firmware watchdog triggers full SER recovery before any VAPs
are up, mac80211 skips drv_reconfig_complete() because open_count is
zero. This leaves the DRIVER queue stop reason set permanently,
blocking all TX when interfaces eventually start.
Signed-off-by: Chad Monroe <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The flow is added to dev->twt_list before sending the agreement to the
firmware, but the error path leaves it linked while flowid_mask is
never set. The flow slot can then be reused and memset while still on
the list, corrupting twt_list, and station removal leaves a dangling
entry behind that mt7915_mac_twt_sched_list_add() later walks.
Fixes: 3782b69d03e7 ("mt76: mt7915: introduce mt7915_mac_add_twt_setup routine")
Signed-off-by: Felix Fietkau <[email protected]>
The per-chain response-frame RSSI values are packed one per byte, but the
4th chain was extracted with GENMASK(31, 14) instead of GENMASK(31, 24).
The wrong mask overlaps chains 1-3 and shifts by 14, producing a garbage
chain-3 value that corrupts ack_signal/avg_ack_signal on 4x4 radios.
Extract the correct byte.
Fixes: a71b648e3527 ("wifi: mt76: mt7915: add ack signal support")
Fixes: ea5d99d07fbf ("wifi: mt76: mt7996: enable ack signal support")
Fixes: 67fc7a304bf5 ("wifi: mt76: mt7921: add ack signal support")
Fixes: c948b5da6bbe ("wifi: mt76: mt7925: add Mediatek Wi-Fi7 driver for mt7925 chips")
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
When performing a full system recovery of the MCU on a dual-phy
platform, band 0 (usually 2.4GHz) stops reading correct noise floor
data.
This is due to noise floor reporting only being configured correctly
for the second device PHY.
Configure the respective registers correctly after restarting the MCU
firmware to fix reported noise-floor values.
Signed-off-by: David Bauer <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
When FIELD_GET returns 0 for the retry count, subtracting 1 causes
an unsigned integer underflow, resulting in tx_retries becoming a
very large value (0xFFFFFFFF for u32).
Fix by checking if count is non-zero before subtracting 1.
Fixes: 943e4fb96e6f ("wifi: mt76: mt7915: report tx retries/failed counts for non-WED path")
Signed-off-by: Ryder Lee <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76_abort_scan routine out of mt76_reset_device() in order to
avoid a possible deadlock since mt76_reset_device routine is running
with mt76 mutex help and mt76_abort_scan_complete() can grab mt76 mutex
in some cases.
Fixes: b36d55610215a ("wifi: mt76: abort scan/roc on hw restart")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Tested-by: Ben Greear <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
The current WED only supports 256 wcid, whereas mt7986 can support up to
512 entries, so firmware provides a rule to get sta_info by DA when wcid
is set to 0x3ff by txd. Also, WED provides a register to overwrite txd
wcid, that is, wcid[9:8] can be overwritten by 0x3 and wcid[7:0] is set
to 0xff by host driver.
However, firmware is unable to get sta_info from DA as DA != RA for
4addr cases, so firmware and wifi host driver both use wcid (256 - 271)
and (768 ~ 783) for sync up to get correct sta_info.
Currently WDS+WED config is completely broken on MT7986/7981 devices if
without this patch.
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Sujuan Chen <[email protected]>
Signed-off-by: Shengyu Qu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
MediaTek has asked to switch from the ISC license to BSD-3-Clause-Clear,
in order to improve clarity and the legal integrity of the code.
The BSD-3-Clause license includes the "no endorsement" clause, which is
important for protecting the reputation of the original authors and
contributors by preventing unauthorized use of their names for endorsement
purposes.
This clause is absent in the BSD-2-Clause license, which is more permissive
but lacks this specific protection.
This change also cleans up the license of some Kconfig/Makefile files,
which were accidentally marked as GPL.
The GPL 2.0 remains in use on mt76x0, as well as two source files in mt7615
for which the license situation still needs to be clarified.
Signed-off-by: Felix Fietkau <[email protected]>
Since stations are recreated from scratch, all lists that wcids are added
to must be cleared before calling ieee80211_restart_hw.
Set wcid->sta = 0 for each wcid entry in order to ensure that they are
not added again before they are ready.
Signed-off-by: Felix Fietkau <[email protected]>
Several places use rcu_dereference to get a wcid entry without validating
if the index exceeds the array boundary. Fix this by using a helper function,
which handles validation.
Signed-off-by: Felix Fietkau <[email protected]>
The definition of MT_RX_SEL (for rdd_rx_sel) is mixed with the
definition of HWRDD idx.
For example, MT_RX_SEL2 is for background HWRDD idx, not an option
of rdd_rx_sel.
Therefore, add mt7915_get_rdd_idx as a helper function to get the
HWRDD idx for each variants.
Additionally, remove some parts of the code inherited from the legacy
chips.
For instance,
1. rdd_state is used for single-band-dual-HWRDD chips (for 80+80),
especially the 76xx series.
2. rdd_rx_sel is also used for single-band-dual-HWRDD chips
rx_sel = 0 => RDD0 for WF0, RDD1 for WF2
rx_sel = 1 => RDD0 for WF1, RDD1 for WF3
Chip Variants | 5G rdd idx(=bandidx)| Background rdd idx
-------------------------------|---------------------|-------------------
MT7915A | 0 | 2
MT7915D | 1 | 2
MT7916 2G + 5G (2T2R+1R) | 1 | 2
MT7916 2G + 5G (3T3R) | 1 | N/A
MT7981 2G + 5G | 1 | N/A
MT7986 2G + 5G (one adie DBDC) | 1 | N/A
MT7986 5G (one adie) | 1 (bandidx=MT_BAND1)| N/A
MT7986 2G + 5G (dual adie) | 1 | N/A
Signed-off-by: StanleyYP Wang <[email protected]>
Reviewed-by: Shayne Chen <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
mt76 does a lot of:
local_bh_disable();
napi_enable(...napi);
napi_schedule(...napi);
local_bh_enable();
local_bh_disable() is not a real lock, its most likely taken
because napi_schedule() requires that we invoke softirqs at
some point. napi_enable() needs to take a mutex, so move it
from under the BH protection.
Fixes: 413f0271f396 ("net: protect NAPI enablement with netdev_lock()")
Reported-by: Dan Carpenter <[email protected]>
Link: https://lore.kernel.org/[email protected]
Reviewed-by: Eric Dumazet <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
Fixes linked list management issues during restart, where sta entries
can be recreated and reinitialized while still in the poll list, triggering
kernel warnings.
Signed-off-by: Felix Fietkau <[email protected]>
Reset per-phy mac address slot mask in order to avoid leaking entries.
Fixes: 8a55712d124f ("wifi: mt76: mt7915: enable full system reset support")
Signed-off-by: Felix Fietkau <[email protected]>
It seems that the firmware checks the register used for detecting matching
PCIe links in order to figure out if a secondary PCIe link is enabled.
Write the register again just before starting the firmware on hw reset,
in order to fix an issue that left the second band unusable after restart.
Fixes: 9093cfff72e3 ("mt76: mt7915: add support for using a secondary PCIe link for gen1")
Signed-off-by: Felix Fietkau <[email protected]>
Do not trigger full restarts when running into timeouts during SER.
Immediately abort MCU commands when firmware requests DMA restart.
Signed-off-by: Felix Fietkau <[email protected]>
- use reconfig_complete to restart mac_work / queues
- reset full wtbl after firmware init
- clear wcid and vif mask to avoid leak
Signed-off-by: Felix Fietkau <[email protected]>
When ieee80211_restart_hw is called, all interfaces and stations are
recreated. This can lead to corruption in the sta poll list, since
existing entries were not removed before their private data is reset.
Signed-off-by: Felix Fietkau <[email protected]>
Do not report measurements if the airtime counter was cleared since the
last update (possibly by firmware)
Signed-off-by: Henry Yen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Do not clear the interrupt mask register on MT7915, since that prevents
MCU_CMD interrupts from being reported, thus causing timeouts during the
reset sequence. Defer stopping WED until tx/rx processing activity has
stopped.
Signed-off-by: Felix Fietkau <[email protected]>
Use per-phy structure for maximum txpower value initializing, since each
phy may have a different chainmask, which can impact the calculation of
power gain.
Co-developed-by: Allen Ye <[email protected]>
Signed-off-by: Allen Ye <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The error handling code was added in order to allow tx enqueue to fail after
calling .tx_prepare_skb. Since this can no longer happen, the error handling
code is unused.
Signed-off-by: Felix Fietkau <[email protected]>
Move the following routines in mt76-connac lib since they are shared
between mt7915 and mt7921:
- mt76_connac2_tx_check_aggr
- mt76_connac2_txwi_free
- mt76_connac2_tx_token_put
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
ampdu_state field is used by most of the drivers, so move it in
mt76_wcid structure.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
poll_list field is used by most of the drivers, so move it in mt76_wcid
structure.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
sta_poll_list and sta_poll_lock are used by most of the drivers, so move
them in mt76_dev structure.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Stop WFDMA transaction to avoid potential unexpected issue while doing
system recovery.
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The stats are clear-on-read, which makes it very difficult for tools
to adequately deal with wrapped stats and with keeping good totals.
So, accumulate these values when they are read from the firmware/radio
and present totals to user-space.
Signed-off-by: Ben Greear <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mib_stats structure is shared by mostly all chipsets. Move it to shared
code.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Get missing tx retries/failed counts from txfree done events and report
them via mt7915_sta_statistics().
Co-developed-by: Peter Chiu <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add support for the MediaTek MT7981 SoC which is similar to the MT7986
but with a newer IP cores and only 2x ARM Cortex-A53 instead of 4x.
Unlike MT7986 the MT7981 can only connect a single wireless frontend,
usually MT7976 is used for DBDC.
Signed-off-by: Alexander Couzens <[email protected]>
Signed-off-by: Daniel Golle <[email protected]>
sta_ps callback is just an empty stub for most of the drivers,
so get rid of them.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
irq_tasklet struct is used by most of the drivers (e.g. mt7915, mt7921,
mt7615, mt7663 and mt7996) so move it in common code.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The previous commit forgot to remove a leftover check.
Fixes: 43eaa3689507 ("wifi: mt76: add PPDU based TxS support for WED device")
Reported-By: Sujuan Chen <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This patch does not change any logic, just improve code readability.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The commit dc44c45c8cd0 added band_idx into mt76_phy, so switching to
rely on that.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The commit 006b9d4ad5bf introduced phy->band_idx to accommodate the
band definition change for mt7986 so that the band_idx of main_phy
can be 0 or 1. Accordingly, the source of band_idx 1 has switched to
"phy != &dev->phy" or "dev->phy.band_idx = 1".
We still use ext_phy to represent band 1 somewhere in driver, so fix it.
Also, band_idx sounds more reasonable than dbdc_idx, so change it.
Fixes: 006b9d4ad5bf ("mt76: mt7915: introduce band_idx in mt7915_phy")
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
It should use dev->mt76.mmio.irqmask instead.
Fixes: 337acff38223 ("wifi: mt76: mt7915: enable full system reset support")
Signed-off-by: Ryder Lee <[email protected]>
Felix Fietkau