Introduce mtk_wed_device pointer in mt76_queue structure in order to
configure WED chip.
Get rid of dev parameter in Q_READ and Q_WRITE macros.
Introduce wed parameter to the following routine signatures:
- mt76_init_queue
- mt76_init_tx_queue
This is a preliminary patch to introduce WED support for mt7996 since
mt7996 runs two separate WED chips.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Enable PPDU TxS by default. This makes the driver able to get Tx rate
information from TxS. The driver will also refresh BA session timer
on receive of PPDU TxS when WED is on.
Signed-off-by: Yi-Chia Hsieh <[email protected]>
Signed-off-by: Money Wang <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Evelyn Tsai <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Extend settings of LED registers to support per-band configuration.
Signed-off-by: Jen-Hao Cheng <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
According to P802.11be_D3.2 Table 9-404m, the minimum value of
Beamformee SS field shall be 3. Fix the values to follow the spec.
Fixes: 348533eb968d ("wifi: mt76: mt7996: add EHT capability init")
Signed-off-by: Howard Hsu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rely on sta_poll_list and sta_poll_lock fields in mt76_dev structure
and get rid of private copies.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Set SUPPORTS_VHT_EXT_NSS_BW to let the max BW capability correctly be
parsed by different devices.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The Group ID Management frame is an Action frame of category VHT.
It is transmitted by the AP to assign or change the user position
of a STA for one or more group IDs.
Also, sniffer can use a given group id to monitor STA that belongs
to that group.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
gen_ppe_thresh routine is shared between mt7615, mt7915, mt7921 and
mt7996 so move it in mt76_connac module.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
irq_tasklet struct is used by most of the drivers (e.g. mt7915, mt7921,
mt7615, mt7663 and mt7996) so move it in common code.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The connac3 removes fixed rate fields to reduce txd size and introduces
global rate tables (64 entries) for rate setting. Driver needs to fill
the corresponding idx in MT_TXD6_TX_RATE while tx, and push mt76_rate
into predifined table at bootup stage so that mvif->basic_rates_idx
can immediately switch out once setting changes.
spe_idx is also needed for fixed rate frames, and will be updated by
future patches.
Note that all table entries are shared across driver and firmware
(i.e.TxBF), hence adding MT7996_BASIC_RATES_TBL to reflect mapping
status.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Host triggered and catastrophic event triggered firmware core dumping
for basic firmware issues triage, including state reporting, function
calltrace and MCU memory dump.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add mt7996_reset() and refactor mt7996_mac_reset_work() to support
full system recovery.
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Init mpdu density based on the hardware capability to prevent rx drop.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rework and extract common code of capability init for the preparation of
adding EHT capability.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add helpers to get the maximum wtbl size and interface num based
on hw caps.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use the sts variable when setting vht beamform sts cap.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move leds struct in mt76_phy in order to have leds associated to phy
(e.g. in dbdc mode) instead of per device.
Tested-by: Frank Wunderlich <[email protected]>
Co-developed-by: Ryder Lee <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This reports signal strength of ACK packets from the peer as measured
at each interface.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
