If the device is reset, suspended or unregistered within that window,
the pending work can still run and access vif/bss data that may already
be freed, or send MCU commands while the firmware is not available.
Add cancel_delayed_work_sync(&dev->mlo_pm_work) in all relevant teardown
and suspend paths:
- mt7925_mac_reset_work() (chip reset recovery)
- mt7925e_unregister_device() (PCIe unbind)
- mt7925_pci_suspend() (PCIe bus suspend)
- mt7925_suspend() (mac80211 suspend)
- mt7925u_suspend() (USB bus / runtime suspend)
This ensures the work is stopped before the device state becomes
invalid.
Assisted-by: kimi-cli:kimi-k2.7 code
Assisted-by: atomcode:glm-5.2 #Reported-by
Fixes: 276a568832577 ("wifi: mt76: mt7925: update the power-saving flow")
Cc: [email protected]
Signed-off-by: Wentao Guan <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Skip mt7925 reset handling once the bus is marked hung.
A hung bus cannot be recovered by issuing another device reset. Continuing
the reset path may only send more failing MCU or register accesses and
delay teardown. Return early from reset work and the USB reset path so the
failed device can be torn down quickly.
Signed-off-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Add per-device USB reset work and a control-path access check helper
for mt7921u and mt7925u.
This prepares common infrastructure for transport-level recovery while
keeping the reset state per-device for correct lifetime handling.
No functional change intended.
Signed-off-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Add the MT7927 USB device ID and normalize the raw 0x6639 CHIPID to
MT7927 so the shared mt7925u code can use the proper chip-specific paths.
Restore the required band setup after USB MAC reset before restarting
the device.
Signed-off-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Driver core holds a reference to the USB interface and its parent USB
device while the interface is bound to a driver and there is no need to
take additional references unless the structures are needed after
disconnect.
Drop the redundant device reference to reduce cargo culting, make it
easier to spot drivers where an extra reference is needed, and reduce
the risk of memory leaks when drivers fail to release it.
Signed-off-by: Johan Hovold <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
MediaTek has asked to switch from the ISC license to BSD-3-Clause-Clear,
in order to improve clarity and the legal integrity of the code.
The BSD-3-Clause license includes the "no endorsement" clause, which is
important for protecting the reputation of the original authors and
contributors by preventing unauthorized use of their names for endorsement
purposes.
This clause is absent in the BSD-2-Clause license, which is more permissive
but lacks this specific protection.
This change also cleans up the license of some Kconfig/Makefile files,
which were accidentally marked as GPL.
The GPL 2.0 remains in use on mt76x0, as well as two source files in mt7615
for which the license situation still needs to be clarified.
Signed-off-by: Felix Fietkau <[email protected]>
When the system suspend or resume, the WiFi driver sends
an hif_ctrl command to the firmware and waits for an event.
Due to changes in the event format reported by the chip, the
current mt7925's driver does not account for these changes,
resulting in command timeout. Add flow to handle hif_ctrl
event to avoid command timeout. We also exented API
mt76_connac_mcu_set_hif_suspend for connac3 this time.
Signed-off-by: Quan Zhou <[email protected]>
Link: https://patch.msgid.link/3a0844ff5162142c4a9f3cf7104f75076ddd3b87.1735910562.git.quan.zhou@mediatek.com
Signed-off-by: Felix Fietkau <[email protected]>
Also report auth/disassoc events, in order to give the driver more control over
handling the station state.
Signed-off-by: Felix Fietkau <[email protected]>
Move the following shared usb routines in mt792x module:
- mt792xu_stop
- mt792x_stop
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Since mt7921_skb_add_usb_sdio_hdr is shared between mt7925 and mt7921
drivers, move it in mt792x module.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add mt7925, a new mac80211 driver for the MediaTek Wi-Fi 7 (802.11be) device
Filogic 360, which can support Station, AP, P2P, and monitor modes.
Filogic 360 supports max 4096-QAM/160MHz radio operation at 6 GHz, 5 GHz,
or 2.4 GHz with 2x2 antennas. This chip supports PCIe and USB bus type.
mt7925 supports Wi-Fi 6E and EHT rate with single link only at this moment,
whereas Wi-Fi 7 and its specific features are working in progress. They will be
introduced in further patches.
The driver is build tested by Intel's kernel test robot with both GCC and Clang
with several architecture. Sparse reports no warnings.
There are multiple authors, they are listed in alphabetical order below.
Co-developed-by: Hao Zhang <[email protected]>
Signed-off-by: Hao Zhang <[email protected]>
Co-developed-by: Leon Yen <[email protected]>
Signed-off-by: Leon Yen <[email protected]>
Co-developed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Co-developed-by: Mingyen Hsieh <[email protected]>
Signed-off-by: Mingyen Hsieh <[email protected]>
Co-developed-by: Nelson Yu <[email protected]>
Signed-off-by: Nelson Yu <[email protected]>
Co-developed-by: Quan Zhou <[email protected]>
Signed-off-by: Quan Zhou <[email protected]>
Co-developed-by: Rong Yan <[email protected]>
Signed-off-by: Rong Yan <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
