For the moment offload firmware supports just one entry in the scheduled
scan plan and so it runs till it is disabled by the userspace.
Do not mark the hw scheduled scan as disabled in mt7615_scan_work
after receiving a scan result
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce sta pointer to mt7615_mcu_add_bss_info signature in order to
avoid sta lookup in mt7615_mcu_bss_basic_tlv routine
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Enable mac80211 TDLS support by default. Disable TDLS hw filtering for
mt7615 devices
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce support for mt7663u 802.11ac 2x2:2 chipset to mt7615 driver.
Main difference respect to pcie code base is the usb code needs to
configure wtbl from non-atomic context
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Create mt7615-common module in order to collect shared code between usb
and mmio code. Move the following source files in mt7615-common module:
- main.c
- init.c
- mcu.c
- mac.c
- debugfs.c
- eeprom.c
- trace.c
Create the following source files for mmio only source code and move them
in mt7615e module:
- pci_init.c
- dma.c
- pci_mac.c
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
make mac_work per phy instead of per device and fix a possible deadlock
in mt7615_stop since mt7615_mac_work runs holding mt76 mutex
Fixes: fdd2e570764c2 ("mt76: mt7615: add dual-phy support for mac80211 ops")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When the EEPROM data is read from flash, it can contain tx DPD calibration
data. Add support for sending the data to the firmware.
Signed-off-by: Felix Fietkau <[email protected]>
When the EEPROM data is read from flash, it can contain DC offset calibration
data. Add support for sending the data to the firmware.
Signed-off-by: Felix Fietkau <[email protected]>
mac80211/hostapd runs mt7615_set_channel with the same channel
parameters sending multiple rdd commands overwriting the previous ones.
This behaviour is causing tpt issues on dfs channels.
Fix the issue checking new channel freq/width with the running one.
Fixes: 5dabdf71e94e ("mt76: mt7615: add multiple wiphy support to the dfs support code")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce rlm tlv header in bss_info mcu command in order to
inform the mcu about operating channel. Rlm header is necessary only if
the mcu is running low power functionalities (e.g offloaded scan)
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt7615_mcu_set_channel_domain routines in order to instruct
the mcu about supported band/channels. This is a preliminary patch to
add hw scan support to mt7663e driver
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt7615_mcu_set_beacon_offload, mt7615_mcu_set_dev and
mt7615_mcu_set_bss routine in mt7615_mcu_ops data structure.
This is a preliminary patch to support mt7663 firmware
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt7615_mcu_set_sta for fw version 1 and version 2 in mt7615_mcu_ops
data structure. This is a preliminary patch to properly support mt7663e
firmware.
Rework utility routines to rely on skb APIs for msg parsing
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt7615_mcu_set_bmc for fw version 1 and version 2 in
mt7615_mcu_ops data structure. This is a preliminary patch
to properly support mt7663e firmware.
Rework utility routines to rely on skb APIs for msg parsing
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt7615_mcu_ops data structure in order to support multiple
mcu ops API.
Move mt7615_mcu_set_{tx,rx}_ba to mt7615_mcu_ops differentiating between
fw v1 and v2. This is a preliminary patch to properly support mt7663e
firmware.
Rework utility routines to rely on skb APIs for msg parsing
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Overwriting the RMAC_CHFREQ register is not reliable enough, as the firmware
could potentially write it again.
Since there is no PHY index indication in the rx info, we need to use another
way:
If both PHYs are using different channels, find the PHY where chfreq matches
the register value.
The only corner case remaining is when both PHYs are using the same channel.
In that case, the per-packet noise value on the primary PHY will have
information belonging to the chains of the secondary PHY from the previous
received packet of that PHY. The secondary PHY will set noise to 0 for extra
chains.
Signed-off-by: Felix Fietkau <[email protected]>
The second PHY receives no packets unless there is an active vif present.
Set the WANT_MONITOR_VIF flag to deal with that
Signed-off-by: Felix Fietkau <[email protected]>
Setting the tx power by manipulating EEPROM may in some cases not be enough,
since it only covers the base target power and not per-rate offsets.
In other cases, it could limit tx power of rates too much, possibly reducing
throughput or range.
Use firmware support for applying per-rate limit and power offsets for
different values of Nss.
Signed-off-by: Felix Fietkau <[email protected]>
MT7622 does not have a CR4 microcontroller, so it only uses its own N9
firmware.
Co-developed-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
No need to send both MCU_EXT_CMD_SET_RX_PATH and MCU_EXT_CMD_CHANNEL_SWITCH
together to MCU.
Split them out by passing the proper command in the corresponding flow.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add the capability to configure acktimeout for mt7615 driver. Moreover
configure slottime according to the value provided by mac80211
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The MT7615 firmware needs to know the association id at creation time,
which is unavailable during the transition from notexist to none in
.sta_state.
This can cause a number of issues, probably also breaking powersave
support.
Signed-off-by: Felix Fietkau <[email protected]>
Loading the mcu firmware and waiting for it to boot takes a long time,
which adds a significant amount to the system boot time.
Fix this by running the mcu init from a workqueue and waiting for it to
complete before starting the phy or issuing mcu commands via debugfs
Signed-off-by: Felix Fietkau <[email protected]>
Program the RMAC CHFREQ registers to properly indicate the band that the
frames are received on.
Add some sanity checks to the programmed values, because the firmware
programs these registers differently
Signed-off-by: Felix Fietkau <[email protected]>
There are two DFS detectors on the chip. When using 160 MHz channel bandwidth
(not supported in dual-wiphy mode), both are used. Otherwise, one detector is
used per wiphy.
Rework the code to start/stop them separately per phy and to indicate the
radar event on the right phy based on the detector index
Signed-off-by: Felix Fietkau <[email protected]>
Add support for an extra wiphy in mt76_set_channel and mt76_get_survey
This is preparation for supporting multiple wiphys per device to support the
concurrent dual-band feature of MT7615D
Signed-off-by: Felix Fietkau <[email protected]>
This is preparation for supporting multiple wiphys per device to support the
concurrent dual-band feature of MT7615D
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76_get_antenna in mac80211.c in order to be reused by all
drivers. Initialize .get_antenna function pointer for mt76x0, mt7603,
mt7615 and mt76x2u drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
