Move mt76x2_rate definition in mt76x02-lib module and rename it in
mt76x02_rates in order to be reused in mt76x0 driver.
Moreover remove unused mt76_rate definition
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Stanislaw Gruszka <[email protected]>
Use common sta_rate_tbl_update on mt76x0 and mt76x2.
mt76x0 do not have support TPC (transmision power control) implmented,
msta->wcid.max_txpwr_adj is only set for mt76x2.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Move rxfilter and mutex to common structure. Create mt76x02-lib.ko
for mt76x0 and mt76x2 common functions and create new unified
mt76x02_configure_filter() function there.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Create new mt76x02_mac.h for common mac functions of mt76x0 and mt76x2
and unity wait_for_mac for both drivers.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Move init related code shared between mt76x2 and mt76x2u in
mt76x2-common module
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Move mac related code shared between mt76x2 and mt76x2u in
mt76x2-common module
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Move wiphy interface_modes definition in mt76x2_init in order to
reuse mt76_register_device routine supporting mt76x2u based chipsets
since mt76x2u currently supports just sta mode
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Add mt76x2_init_device routine in order to reuse common pcie/usb mac80211
initialization code supporting mt76x2u based device
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
In order to reuse them supporting mt76x2u based devices, move
mt76x2_wait_for_mac, wait_for_wpdma and mt76x2_channel_silent in
mt76x2.h
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
It is no longer necessary for client mode operation, vif index entries
8-16 are no longer used
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use 11M as tx rate for CCK protection control frames
Fixes: 7bc04215a66b ("mt76: add driver code for MT76x2e")
Signed-off-by: Lorenzo Bianconi <[email protected]>
usleep_range can cause excessive latency on channel change if waiting
for the MAC to stop fails. It will be forced to stop by the code
following that loop anyway.
Signed-off-by: Felix Fietkau <[email protected]>
According to 802.11-2007 17.3.8.6 (slot time), the slot time should
be increased by 3 us * coverage class. Taking into account coverage
class in slot time configuration allows to increase by an order of
magnitude the throughput on a 4Km link in a noisy environment
Tested-by: Luca Bisti <[email protected]>
Tested-by: Gaetano Catalli <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
For encryption to work properly, the BSS index needs to be initialized
for the WCID entry used for the interface.
Signed-off-by: Felix Fietkau <[email protected]>
Add a usleep_range in mt76x2_mac_stop routine in order to add
a polling delay checking values of MT_MAC_STATUS and IBI_R12 registers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Add static qualifier to mt76x2_mac_reset routine and remove the
prototype from mt76x2_mac.h since it is used just in mt76x2_init.c
Signed-off-by: Lorenzo Bianconi <[email protected]>
Initialize available_antennas related info in wiphy data structure
according to antenna_mask field; antenna_mask info is initialized
in device specific code and will be used in mac80211 {set,get}_antenna
callbacks
Signed-off-by: Lorenzo Bianconi <[email protected]>
With software A-MPDU reordering in place, frames that notify mac80211 of
powersave changes are reordered as well, which can cause connection
stalls. Fix this by implementing powersave state processing in the
driver.
Signed-off-by: Felix Fietkau <[email protected]>
There is a possible race in mt76x2_stop_hardware() since pre_tbtt and
dfs tasklets could run during driver cleanup. Fix it disabling all
pending tasklets during device removal
Signed-off-by: Lorenzo Bianconi <[email protected]>
Apparently hardware does not perform CCMP PN validation in hardware, so
we need to take care of this in the driver.
Signed-off-by: Felix Fietkau <[email protected]>
Add mt76x2_dfs_set_domain routine in order to properly reconfigure
pattern detector when DFS domain has been changed
Signed-off-by: Lorenzo Bianconi <[email protected]>
mt76x2_mac_start writes dev->rxfilter to the hardware. It also happens
during init, before dev->rxfilter is filled with the initval register
value, leading to issues like promisc mode being enabled
unconditionally.
Fix this by reading the default value into dev->rxfilter earlier
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
It is no longer necessary for client mode operation, vif index entries
8-16 are no longer used
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The hardware has a separate set of registers to configure a
per-interface MAC address.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
add hw DFS pattern detector support for mt76x2 based devices
DFS region supported:
- FCC
- ETSI
- JAPAN_W53
- JAPAN_W56
Signed-off-by: Lorenzo Bianconi <[email protected]>
