Commit d2b01fbc32 ("mt76: pass LED define via ccflags-y")
converted the top-level Makefile from the deprecated EXTRA_CFLAGS
to ccflags-y so that -DCONFIG_MT76_LEDS keeps working now that
kbuild no longer honours EXTRA_CFLAGS.
However, ccflags-y (like EXTRA_CFLAGS before it) only applies to
the kbuild makefile it is set in and is not inherited by
subdirectories pulled in via obj-y/obj-m. The mt7603, mt7615 and
mt7915 driver subdirectories each set their own
"EXTRA_CFLAGS += ... -DCONFIG_MT76_LEDS", which is now a silent
no-op. As a result CONFIG_MT76_LEDS is undefined when building
mt7603/init.c, mt7615/init.c, mt7615/pci_init.c and mt7915/init.c,
the IS_ENABLED(CONFIG_MT76_LEDS) blocks are compiled out, and the
mt76-* LED class devices are never registered for these drivers.
Convert these subdirectory Makefiles to ccflags-y as well.
mt7996/Makefile never carried the define at all, even though
mt7996/init.c has the same IS_ENABLED(CONFIG_MT76_LEDS) checks for
its LED callbacks and GPIO mux setup. Add ccflags-y there too so
mt7996 LED support is enabled consistently with the other drivers.
mt76x0, mt76x2, mt7921 and mt7925 contain no CONFIG_MT76_LEDS
references and are left untouched.
Fixes: d2b01fbc32 ("mt76: pass LED define via ccflags-y")
Link: https://github.com/openwrt/mt76/issues/1077
Signed-off-by: Mateus B. Cassiano <[email protected]>
MediaTek has asked to switch from the ISC license to BSD-3-Clause-Clear,
in order to improve clarity and the legal integrity of the code.
The BSD-3-Clause license includes the "no endorsement" clause, which is
important for protecting the reputation of the original authors and
contributors by preventing unauthorized use of their names for endorsement
purposes.
This clause is absent in the BSD-2-Clause license, which is more permissive
but lacks this specific protection.
This change also cleans up the license of some Kconfig/Makefile files,
which were accidentally marked as GPL.
The GPL 2.0 remains in use on mt76x0, as well as two source files in mt7615
for which the license situation still needs to be clarified.
Signed-off-by: Felix Fietkau <[email protected]>
Add support for the MediaTek MT7981 SoC which is similar to the MT7986
but with a newer IP cores and only 2x ARM Cortex-A53 instead of 4x.
Unlike MT7986 the MT7981 can only connect a single wireless frontend,
usually MT7976 is used for DBDC.
Signed-off-by: Alexander Couzens <[email protected]>
Signed-off-by: Daniel Golle <[email protected]>
Host triggered and catastrophic event triggered firmware core dumping
for basic firmware issues triage, including state reporting, task/irq
info, function calltrace and MCU memory dump.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add mmio.c in order to use mt76_bus_ops throughout the driver.
It will be also shared with the future APSoC revision.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Support testmode tx for MT7915A, including tx streams and HE rate
settings.
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add support for the MediaTek latest generation IEEE 802.11ax 4x4
device MT7915E, which supports concurrent dual-band operation at
both 5GHz and 2.4GHz.
Note that this patch just add basic part and will add more HE
capabilities support in the further patches.
The driver supports AP, Station, Mesh and monitor mode.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Chih-Min Chen <[email protected]>
Suggested-by: Shihwei Lin <[email protected]>
Tested-by: Evelyn Tsai <[email protected]>
Acked-by: Yiwei Chung <[email protected]>
Acked-by: YF Luo <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
