This allows the core code to change the channel. Code deduplication and
preparation for adding scanning code to the core.
Signed-off-by: Felix Fietkau <[email protected]>
tx_rate can't be greater than 3 in mt76x0_phy_get_target_power routine
for cck rates. Get rid of dead code.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Run mt76x02_set_ethtool_fwver utility routine in mt76x0u_load_firmware()
in order to report firmware version through ethtool
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
After 'commit ba45841ca5eb ("wifi: mt76: mt76x02: simplify struct
mt76x02_rate_power")', mt76x02 relies on ht[0-7] rate_power data for
vht mcs{0,7}, while it uses vth[0-1] rate_power for vht mcs {8,9}.
Fix a possible out-of-bound access in mt76x0_phy_get_target_power routine.
Fixes: ba45841ca5eb ("wifi: mt76: mt76x02: simplify struct mt76x02_rate_power")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
- remove stbc, because mt76x0 doesn't support it and mt76x2 uses the same
values as HT/VHT
- reduce vht array to 2 elements, because VHT MCS0-7 are the same as HT
Signed-off-by: Felix Fietkau <[email protected]>
Introduce __mt76u_init unitility routine and move mt7615 usb bus ops
into mt7615 module in order to allow specifying driver specific
parameter.
This is a preliminary patch to add usb support to mt7921 driver.
Tested-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add SAR spec support to mt76x02 driver to allow configuring SAR power
limitations on the frequency ranges from the userland.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Appears to have incorrectly offset 0x120 + 0x12 instead of 12 decimal,
leading to bogus power values being used.
Signed-off-by: Richard Huynh <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
napi_schedule() can call __raise_softirq_irqoff(), which can perform softirq
handling, so it must not be called in a pure process context with BH enabled.
Signed-off-by: Felix Fietkau <[email protected]>
BIT(0) in MT_EE_NIC_CONF_1 is use to notify the driver if the radio RF
switch is controlled through a gpio. Use dev_debug instead of dev_err
to log this info.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mac_work delayed_work and mac_work_count in mt76_phy since it is
used by all drivers. This is a preliminary patch to create a common mcu
library used by mt7615 and mt7921 drivers
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to properly support mt7915 dbdc
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to move properly support mt7915 dbdc
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Run mt76_free_device instead of ieee80211_free_hw if device probing
fails in order to remove the already allocated mt76 workqueue
Fixes: a86f1d01f5ce5 ("mt76: move mt76 workqueue in common code")
Fixes: f1d962369d568 ("mt76: mt7915: implement HE per-rate tx power support")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Taking the same approach as initvals_phy.h.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/mediatek/mt76/mt76x0/initvals.h:218:35: warning: ‘mt76x0_dcoc_tab’ defined but not used [-Wunused-const-variable=]
218 | static const struct mt76_reg_pair mt76x0_dcoc_tab[] = {
| ^~~~~~~~~~~~~~~
drivers/net/wireless/mediatek/mt76/mt76x0/initvals.h:86:35: warning: ‘mt76x0_bbp_init_tab’ defined but not used [-Wunused-const-variable=]
86 | static const struct mt76_reg_pair mt76x0_bbp_init_tab[] = {
| ^~~~~~~~~~~~~~~~~~~
drivers/net/wireless/mediatek/mt76/mt76x0/initvals.h:48:35: warning: ‘mt76x0_mac_reg_table’ defined but not used [-Wunused-const-variable=]
48 | static const struct mt76_reg_pair mt76x0_mac_reg_table[] = {
| ^~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/mediatek/mt76/mt76x0/initvals.h:14:35: warning: ‘common_mac_reg_table’ defined but not used [-Wunused-const-variable=]
14 | static const struct mt76_reg_pair common_mac_reg_table[] = {
| ^~~~~~~~~~~~~~~~~~~~
Cc: Felix Fietkau <[email protected]>
Cc: Lorenzo Bianconi <[email protected]>
Cc: Ryder Lee <[email protected]>
Cc: Kalle Valo <[email protected]>
Cc: "David S. Miller" <[email protected]>
Cc: Jakub Kicinski <[email protected]>
Cc: Matthias Brugger <[email protected]>
Cc: Stanislaw Gruszka <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Signed-off-by: Lee Jones <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76 workqueue from usb to common code in order to be reused adding
low-power support for mt7663 chipset
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add mt7610 PCI id found on D-Link DWR-960 to pci_device_id table.
Run-tested on D-Link DWR-960 with no-name half-size mPCIE card
with mt7610e.
Signed-off-by: Pawel Dembicki <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/mediatek/mt76/mt76x0/phy.c: In function mt76x0_phy_rf_init:
drivers/net/wireless/mediatek/mt76/mt76x0/phy.c:1158:5: warning: variable val set but not used [-Wunused-but-set-variable]
Fixes: 10de7a8b4ab9 ("mt76x0: phy files")
Signed-off-by: Chen Wandun <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
If a MCU timeout occurs before a hw restart completes, another hw restart
is scheduled, and the station state gets corrupted.
To speed up dealing with that, do not issue any MCU commands after the first
timeout, and defer handling timeouts until the reset has completed.
Also ignore errors in MCU commands during start/config to avoid making user
space fail on this condition. If it happens, another restart is scheduled
quickly, and that usually recovers the hardware properly.
Signed-off-by: Felix Fietkau <[email protected]>
Introduce extended utility routines to read/write data o usb bus. New
devices (e.g. mt7663u) will rely on both upper and lower part of the
register address. Add ext parameter to mt76u_init signature in order to
reuse the code adding mt7663u support.
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mcu buffer allocation in mt76x2u/mt76x0u drivers since newer
chipsets (e.g. mt7663u) does not rely on synchronous mcu communication
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Starting from 'commit ee8040139ab1 ("mt76: do not overwrite
max_tx_fragments if it has been set")' we can avoid overwriting
max_tx_fragments for mt76x02u devices
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Current implementation always use default eeprom mac address to
configure device registers even if it is updated using
mt76_eeprom_override. Fix it initializing macaddr filed of mt76_dev data
structure with eeprom mac address and running mt76_eeprom_override
before mt76x02_mac_setaddr
Fixes: d1bc9bf2072c ("mt76: mt76x0: eeprom: add support for MAC address from OF")
Tested-by: Kevin Schmidt <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
[backported from upstream commit 693d060536abca7b16d2fb8e66aa56be2a2443a2]
Signed-off-by: David Bauer <[email protected]>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 655 file(s).
Signed-off-by: Thomas Gleixner <[email protected]>
Reviewed-by: Allison Randal <[email protected]>
Reviewed-by: Kate Stewart <[email protected]>
Reviewed-by: Richard Fontana <[email protected]>
Cc: [email protected]
Link: https://lkml.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
Add support for an extra wiphy in mt76_set_channel and mt76_get_survey
This is preparation for supporting multiple wiphys per device to support the
concurrent dual-band feature of MT7615D
Signed-off-by: Felix Fietkau <[email protected]>
This is preparation for supporting multiple wiphys per device to support the
concurrent dual-band feature of MT7615D
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76_get_antenna in mac80211.c in order to be reused by all
drivers. Initialize .get_antenna function pointer for mt76x0, mt7603,
mt7615 and mt76x2u drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
