The error handling code was added in order to allow tx enqueue to fail after
calling .tx_prepare_skb. Since this can no longer happen, the error handling
code is unused.
Signed-off-by: Felix Fietkau <[email protected]>
mt7921u_disconnect routine is shared between mt7921 and mt7925 so move
it in mt792x-usb module.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt7921_dma_init routine in pci.c and make it static since it is run
just in mt7921_pci_probe(). Get rid of dma.c.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
MT7921_PM_TIMEOUT is shared between mt7925 and mt7921 so move it in
mt792x module.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt7921_load_firmware routine is shared between mt7921 and mt7925 chipset
so move it in mt792x-lib module.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add usb shared code between mt7921 and mt7925 chipset to mt792x-usb module.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move acpi_sar code in mt792x-lib module since it is shared between
mt7921 and mt7925 driver.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move the following runtime-pm pci routines in mt792x-lib since they are
shared between mt7921 and mt7925 chipsets:
- __mt7921e_mcu_drv_pmctrl
- mt7921e_mcu_drv_pmctrl
- mt7921e_mcu_fw_pmctrl
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Moving hif_ops marcos in mt792x.h, we can move shared runtime-pm code
between mt7925 and mt7921 in mt792x-lib module.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rely on irq_map support, move more dma shared code between mt7921 and
mt7925 in mt792x_dma.c
Move the following dma code in mt792x-lib
- mt792x_dma_enable
- mt792x_dma_reset
- mt792x_wpdma_reset
- mt792x_wpdma_reinit_cond
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt792x_irq_map will be use to share the irq code shared between mt7921
and mt7925
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Reduce duplicated code moving mac shared code in mt792x-lib module.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt792x-lib module will contain the shared code between mt7921 and new
MT79 WiFi7 chipset
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Zero-length arrays as fake flexible arrays are deprecated and we are
moving towards adopting C99 flexible-array members instead.
Address the following warnings found with GCC-13 and
-fstrict-flex-arrays=3 enabled:
drivers/net/wireless/mediatek/mt76/mt7921/acpi_sar.c:266:25: warning: array subscript 0 is outside array bounds of ‘struct mt7921_asar_dyn_limit_v2[0]’ [-Warray-bounds=]
drivers/net/wireless/mediatek/mt76/mt7921/acpi_sar.c:263:25: warning: array subscript 0 is outside array bounds of ‘struct mt7921_asar_dyn_limit[0]’ [-Warray-bounds=]
drivers/net/wireless/mediatek/mt76/mt7921/acpi_sar.c:223:28: warning: array subscript <unknown> is outside array bounds of ‘struct mt7921_asar_geo_limit_v2[0]’ [-Warray-bounds=]
drivers/net/wireless/mediatek/mt76/mt7921/acpi_sar.c:220:28: warning: array subscript <unknown> is outside array bounds of ‘struct mt7921_asar_geo_limit[0]’ [-Warray-bounds=]
drivers/net/wireless/mediatek/mt76/mt7921/acpi_sar.c:334:37: warning: array subscript i is outside array bounds of ‘u8[0]’ {aka ‘unsigned char[]’} [-Warray-bounds=]
Notice that the DECLARE_FLEX_ARRAY() helper allows for flexible-array
members in unions.
This helps with the ongoing efforts to tighten the FORTIFY_SOURCE
routines on memcpy() and help us make progress towards globally
enabling -fstrict-flex-arrays=3 [1].
Link: https://github.com/KSPP/linux/issues/21
Link: https://github.com/KSPP/linux/issues/272
Link: https://gcc.gnu.org/pipermail/gcc-patches/2022-October/602902.html [1]
Signed-off-by: Gustavo A. R. Silva <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to introduce WiFi7 chipset support
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to introduce WiFi7 chipset support
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to introduce WiFi7 chipset support
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to introduce WiFi7 chipset support
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to introduce WiFi7 chipset support
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to introduce WiFi7 chipset support
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to introduce WiFi7 chipset support
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to introduce WiFi7 chipset support
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Convert acpisar and clc pointers in mt7921_dev structure to void.
This is a preliminary patch to add WiFi7 chipset support
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch in order to support new WiFi7 chips.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move the following routines in mt76-connac lib since they are shared
between mt7915 and mt7921:
- mt76_connac2_tx_check_aggr
- mt76_connac2_txwi_free
- mt76_connac2_tx_token_put
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
ampdu_state field is used by most of the drivers, so move it in
mt76_wcid structure.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rely on poll_list field in mt76_wcid structure and get rid of
private copy.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rely on sta_poll_list and sta_poll_lock fields in mt76_dev structure
and get rid of private copies.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
For some cases as below, we may encounter the unpreditable chip stats
in driver probe()
* The system reboot flow do not work properly, such as kernel oops while
rebooting, and then the driver do not go back to default status at
this moment.
* Similar to the flow above. If the device was enabled in BIOS or UEFI,
the system may switch to Linux without driver fully shutdown.
To avoid the problem, force push the device back to default in probe()
* mt7921e_mcu_fw_pmctrl() : return control privilege to chip side.
* mt7921_wfsys_reset() : cleanup chip config before resource init.
Error log
[59007.600714] mt7921e 0000:02:00.0: ASIC revision: 79220010
[59010.889773] mt7921e 0000:02:00.0: Message 00000010 (seq 1) timeout
[59010.889786] mt7921e 0000:02:00.0: Failed to get patch semaphore
[59014.217839] mt7921e 0000:02:00.0: Message 00000010 (seq 2) timeout
[59014.217852] mt7921e 0000:02:00.0: Failed to get patch semaphore
[59017.545880] mt7921e 0000:02:00.0: Message 00000010 (seq 3) timeout
[59017.545893] mt7921e 0000:02:00.0: Failed to get patch semaphore
[59020.874086] mt7921e 0000:02:00.0: Message 00000010 (seq 4) timeout
[59020.874099] mt7921e 0000:02:00.0: Failed to get patch semaphore
[59024.202019] mt7921e 0000:02:00.0: Message 00000010 (seq 5) timeout
[59024.202033] mt7921e 0000:02:00.0: Failed to get patch semaphore
[59027.530082] mt7921e 0000:02:00.0: Message 00000010 (seq 6) timeout
[59027.530096] mt7921e 0000:02:00.0: Failed to get patch semaphore
[59030.857888] mt7921e 0000:02:00.0: Message 00000010 (seq 7) timeout
[59030.857904] mt7921e 0000:02:00.0: Failed to get patch semaphore
[59034.185946] mt7921e 0000:02:00.0: Message 00000010 (seq 8) timeout
[59034.185961] mt7921e 0000:02:00.0: Failed to get patch semaphore
[59037.514249] mt7921e 0000:02:00.0: Message 00000010 (seq 9) timeout
[59037.514262] mt7921e 0000:02:00.0: Failed to get patch semaphore
[59040.842362] mt7921e 0000:02:00.0: Message 00000010 (seq 10) timeout
[59040.842375] mt7921e 0000:02:00.0: Failed to get patch semaphore
[59040.923845] mt7921e 0000:02:00.0: hardware init failed
Fixes: 5c14a5f944b9 ("mt76: mt7921: introduce mt7921e support")
Tested-by: Kai-Heng Feng <[email protected]>
Co-developed-by: Leon Yen <[email protected]>
Signed-off-by: Leon Yen <[email protected]>
Signed-off-by: Quan Zhou <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Tested-by: Juan Martinez <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
MT7921_RESET_TIMEOUT is never used, so get rid of it.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Make mt7921_mac_sta_poll static since it is run just in mac.c
Signed-off-by: Lorenzo Bianconi <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Due to the scan command may only request legacy bands and PSC channel
in 6GHz band, we are unable to scan the APs on non-PSC channel in this
case. Enable WIPHY_FLAG_SPLIT_SCAN_6GHZ to support non-PSC channel
(obtained during scan on legacy bands) in 6GHz scan request.
Fixes: 50ac15a511e3 ("mt76: mt7921: add 6GHz support")
Signed-off-by: Ming Yen Hsieh <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Get missing tx retries/failed counts from txfree done events and report
them via mt7921_sta_statistics().
Signed-off-by: Deren Wu <[email protected]>
Reviewed-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Get rid of MT_MIB_RTS_COUNT_MASK marco duplication in mt7921/regs.h
Signed-off-by: Lorenzo Bianconi <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt7921_usb_sdio_tx_prepare_skb() calls mt7921_usb_sdio_write_txwi() and
mt7921_skb_add_usb_sdio_hdr(), both of which blindly assume that
adequate headroom will be available in the passed skb. This assumption
typically is satisfied when the skb was allocated in the net core for
transmission via the mt7921 netdev (although even that is only an
optimization and is not strictly guaranteed), but the assumption is
sometimes not satisfied when the skb originated in the receive path of
another netdev and was passed through to the mt7921, such as by the
bridge layer. Blindly prepending bytes to an skb is always wrong.
This commit introduces a call to skb_cow_head() before the call to
mt7921_usb_sdio_write_txwi() in mt7921_usb_sdio_tx_prepare_skb() to
ensure that at least MT_SDIO_TXD_SIZE + MT_SDIO_HDR_SIZE bytes can be
pushed onto the skb.
Without this fix, I can trivially cause kernel panics by bridging an
MT7921AU-based USB 802.11ax interface with an Ethernet interface on an
Intel Atom-based x86 system using its onboard RTL8169 PCI Ethernet
adapter and also on an ARM-based Raspberry Pi 1 using its onboard
SMSC9512 USB Ethernet adapter. Note that the panics do not occur in
every system configuration, as they occur only if the receiving netdev
leaves less headroom in its received skbs than the mt7921 needs for its
SDIO headers.
Here is an example stack trace of this panic on Raspberry Pi OS Lite
2023-02-21 running kernel 6.1.24+ [1]:
skb_panic from skb_push+0x44/0x48
skb_push from mt7921_usb_sdio_tx_prepare_skb+0xd4/0x190 [mt7921_common]
mt7921_usb_sdio_tx_prepare_skb [mt7921_common] from mt76u_tx_queue_skb+0x94/0x1d0 [mt76_usb]
mt76u_tx_queue_skb [mt76_usb] from __mt76_tx_queue_skb+0x4c/0xc8 [mt76]
__mt76_tx_queue_skb [mt76] from mt76_txq_schedule.part.0+0x13c/0x398 [mt76]
mt76_txq_schedule.part.0 [mt76] from mt76_txq_schedule_all+0x24/0x30 [mt76]
mt76_txq_schedule_all [mt76] from mt7921_tx_worker+0x58/0xf4 [mt7921_common]
mt7921_tx_worker [mt7921_common] from __mt76_worker_fn+0x9c/0xec [mt76]
__mt76_worker_fn [mt76] from kthread+0xbc/0xe0
kthread from ret_from_fork+0x14/0x34
After this fix, bridging the mt7921 interface works fine on both of my
previously problematic systems.
[1] https://github.com/raspberrypi/firmware/tree/5c276f55a4b21345cd4d6200a504ee991851ff7a
Link: https://github.com/openwrt/openwrt/issues/11796
Signed-off-by: Matt Whitlock <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Issue: Though the Netgear AXE3000 (A8000) is based on the mt7921
chipset because of the unique USB VID:PID combination this device
does not initialize/register. Thus making it not plug and play.
Fix: Adds support for the Netgear AXE3000 (A8000) based on the Mediatek
mt7921au chipset. The method of action is adding the USD VID/PID
pair to the mt7921u_device_table[] array.
Notes: A retail sample of the Netgear AXE3000 (A8000) yeilds the following
from lsusb D 0846:9060 NetGear, Inc. Wireless_Device. This pair
0846:9060 VID:PID has been reported by other users on Github.
Signed-off-by: Reese Russell <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In system warm reboot scene, due to the polling timeout(now 1000us)
is too short to wait dma idle in time, it may make driver probe fail
with error code -ETIMEDOUT. Meanwhile, we also found the dma may take
around 70ms to enter idle state. Change the polling idle timeout to
100ms to avoid the probabilistic probe fail.
Tested pass with 5000 times warm reboot on x86 platform.
[4.477496] pci 0000:01:00.0: attach allowed to drvr mt7921e [internal device]
[4.478306] mt7921e 0000:01:00.0: ASIC revision: 79610010
[4.480063] mt7921e: probe of 0000:01:00.0 failed with error -110
Fixes: 0a1059d0f060 ("mt76: mt7921: move mt7921_dma_reset in dma.c")
Signed-off-by: Quan Zhou <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move some mac shared definitions between mt7996, mt7921 and mt7915 in
mt76_connac2_mac.h.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
eeprom.h is mostly empty for mt7921, so get rid of it.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
